diff options
Diffstat (limited to 'nfc/libnfc-hal-st.conf')
-rw-r--r-- | nfc/libnfc-hal-st.conf | 148 |
1 files changed, 148 insertions, 0 deletions
diff --git a/nfc/libnfc-hal-st.conf b/nfc/libnfc-hal-st.conf new file mode 100644 index 0000000..47153d9 --- /dev/null +++ b/nfc/libnfc-hal-st.conf @@ -0,0 +1,148 @@ +########################### Start of libnf-hal-st_aosp.conf ########################### + +############################################################################### +############################################################################### +# ST HAL trace log level +STNFC_HAL_LOGLEVEL=1 +NFC_DEBUG_ENABLED=0 + +############################################################################### +# Vendor specific mode to enable FW (RF & SWP) traces. +STNFC_FW_DEBUG_ENABLED=0 + +############################################################################### +# File used for NFA storage +NFA_STORAGE="/data/nfc" + +############################################################################### +# Keep the nfa storage file. +PRESERVE_STORAGE=1 + +############################################################################### +# In Switch OFF mode (phone switched-off), specify the desired CE mode to +# the controller. +# 0: No card-emulation; DEFAULT +# 1: Switch-off card-emulation enabled +CE_ON_SWITCH_OFF_STATE=1 + +############################################################################### +# Vendor specific mode to support the USB charging mode if VPSIO=1 in switch off. +STNFC_USB_CHARGING_MODE=1 + +############################################################################### +# Vendor Specific Proprietary Protocol & Discovery Configuration +# Set to 0xFF if unsupported +# byte[0] NCI_PROTOCOL_18092_ACTIVE +# byte[1] NCI_PROTOCOL_B_PRIME +# byte[2] NCI_PROTOCOL_DUAL +# byte[3] NCI_PROTOCOL_15693 +# byte[4] NCI_PROTOCOL_KOVIO +# byte[5] NCI_PROTOCOL_MIFARE +# byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO +# byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME +# byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME +NFA_PROPRIETARY_CFG={05:FF:FF:06:8A:90:77:FF:FF} + +############################################################################### +# Choose the presence-check algorithm for type-4 tag. If not defined, +# the default value is 1. +# 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm +# 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block +# 2 NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate +# 3 NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0 +# 4 NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3 +# 5 NFA_RW_PRES_CHK_ISO_DEP_NAK; presence check command ISO-DEP NAK as per NCI2.0 +PRESENCE_CHECK_ALGORITHM=5 + +############################################################################### +# Name of the NCI HAL module to use +# If unset, falls back to nfc_nci.bcm2079x +NCI_HAL_MODULE="nfc_nci.st21nfc" + +############################################################################### +# White list to be set at startup. +DEVICE_HOST_WHITE_LIST={02:C0} + +############################################################################### +# BAIL OUT value for P2P +# Implements algorithm for NFC-DEP protocol priority over ISO-DEP protocol. +POLL_BAIL_OUT_MODE=1 + +############################################################################### +# Extended APDU length for ISO_DEP +ISO_DEP_MAX_TRANSCEIVE=0xFEFF + +############################################################################### +# Configure the NFC Extras to open and use a static pipe. If the value is +# not set or set to 0, then the default is use a dynamic pipe based on a +# destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value +# for each EE (ESE/SIM) +OFF_HOST_ESE_PIPE_ID=0x5E +OFF_HOST_SIM_PIPE_ID=0x3E + +############################################################################### +#Set the default Felica T3T System Code OffHost route Location : +#This settings will be used when application does not set this parameter +# host 0x00 +# eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE) +# UICC 0x81 (UICC_1), 0x85 (UICC_2) +DEFAULT_SYS_CODE_ROUTE=0x86 + +############################################################################### +#Set the Felica T3T System Code supported power state: +DEFAULT_SYS_CODE_PWR_STATE=0x3B + +############################################################################### +# Path and Files used for FW update binaries storage +STNFC_FW_PATH_STORAGE="/vendor/firmware" +STNFC_FW_BIN_NAME="/st54j_fw.bin" +STNFC_FW_CONF_NAME="/st54j_conf.bin" + +############################################################################### +# Default off-host route for Felica. +# This settings will be used when application does not set this parameter +# host 0x00 +# eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE) +# UICC 0x81 (UICC_1), 0x85 (UICC_2) +DEFAULT_NFCF_ROUTE=0x86 + +############################################################################### +# Configure the default off-host route. +# used for technology A and B routing +# eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE) +# UICC 0x81 (UICC_1), 0x85 (UICC_2) +DEFAULT_OFFHOST_ROUTE=0x81 + +############################################################################### +# Configure the default AID route. +# host 0x00 +# eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE) +# UICC 0x81 (UICC_1), 0x85 (UICC_2) +DEFAULT_ROUTE=0x00 + +############################################################################### +# Configure the NFCEEIDs of offhost UICC. +# UICC 0x81 (UICC_1), 0x85 (UICC_2) +OFFHOST_ROUTE_UICC={81} + +############################################################################### +# Configure the NFCEEIDs of offhost eSEs. +# eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE) +OFFHOST_ROUTE_ESE={86} + +############################################################################### +# Configure the list of NFCEE for the ISO-DEP routing. +# host 0x00 +# eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE) +# UICC 0x81 (UICC_1), 0x85 (UICC_2) +DEFAULT_ISODEP_ROUTE=0x81 + +############################################################################### +# Core configuration settings +CORE_CONF_PROP={ 20, 02, 0a, 03, + a1, 01, 1e, + a2, 01, 19, + 80, 01, 01 +} + + |