# This file allows user to override the factory # defaults for the WLAN Driver ############################################# # Power related configurations ############################################# # Phy Mode (auto, b, g, n, etc) # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only # 7 = 11b only 8 = 11ac only. gDot11Mode=0 ############################################# # STA related general configurations ############################################# # UAPSD service interval for VO,VI, BE, BK traffic InfraUapsdVoSrvIntv=0 InfraUapsdViSrvIntv=0 InfraUapsdBeSrvIntv=0 InfraUapsdBkSrvIntv=0 # Flag to allow STA send AddTspec even when ACM is Off gAddTSWhenACMIsOff=1 ############################################# # SAP related configurations ############################################# #Enable OBSS protection gEnableApOBSSProt=1 # RTS threshold RTSThreshold=1048576 # 802.11d support g11dSupportEnabled=0 # DFS Master Capability gEnableDFSMasterCap=0 gNeighborLookupThreshold=76 # Legacy (non-ESE, non-802.11r) Fast Roaming Support # To enable, set FastRoamEnabled=1 # To disable, set FastRoamEnabled=0 FastRoamEnabled=1 # Check if the AP to which we are roaming is better than current AP in # terms of RSSI. Checking is disabled if set to Zero.Otherwise it will # use this value as to how better the RSSI of the new/roamable AP should # be for roaming RoamRssiDiff=3 #Channel Bonding gChannelBondingMode24GHz=0 gChannelBondingMode5GHz=1 # Enable DFS channel roam # 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE gAllowDFSChannelRoam=1 # chain mask related params # # Set txchainmask and rxchainmask # These parameters are used only if gEnable2x2 is 0 # Valid values are 1,2 # Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0. # Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1. gSetTxChainmask1x1=1 gSetRxChainmask1x1=1 # MCC to SCC Switch mode: # 0-Disable # 1-Enable # 2-Force SCC if same band, with SAP restart # 3-Force SCC if same band, without SAP restart by sending (E)CSA # 4-Force SCC if same band (or) use SAP mandatory channel for DBS, # without SAP restart by sending (E)CSA gWlanMccToSccSwitchMode = 3 #Allow STA+SAP SCC on DFS channel with master mode support disabled. g_sta_sap_scc_on_dfs_chan = 0 # 1=enable tx STBC; 0=disable gEnableTXSTBC=1 # 1=enable rx LDPC; 0=disable gEnableRXLDPC=1 #Enable/Disable Tx beamformee in SAP mode gEnableTxBFeeSAP=1 # Enable Tx beamforming in VHT20MHz # Valid values are 0,1. If commented out, the default value is 0. # 0=disable, 1=enable gEnableTxBFin20MHz=1 # 802.11K support gRrmEnable=1 #Enable Power Save offload gEnablePowerSaveOffload=2 # Maximum Receive AMPDU size (VHT only. Valid values: # 0->8k 1->16k 2->32k 3->64k 4->128k) gVhtAmpduLenExponent=7 # Maximum MPDU length (VHT only. Valid values: # 0->3895 octets, 1->7991 octets, 2->11454 octets) gVhtMpduLen=2 # Report actual link speed (not max or scaled) gReportMaxLinkSpeed=0 ############################################# # P2P related configurations ############################################# #Enable or Disable p2p device address administered isP2pDeviceAddrAdministrated=0 #Mac address provisioning enable_mac_provision=1 #Enable VHT on 2.4Ghz gEnableVhtFor24GHzBand=1 ############################################# # Offload related configurations ############################################# # controlling the following offload patterns # through ini parameter. Default value is 1 # to disable set it to zero. ssdp = 0 # Setup multicast pattern for mDNS 224.0.0.251, # SSDP 239.255.255.250 and LLMNR 224.0.0.252 ssdp=0 # Regulatory Setting; 0=STRICT; 1=CUSTOM gRegulatoryChangeCountry=1 # Disable/Enable GreenAP # 0 to disable, 1 to enable, default: 1 gEnableGreenAp=0 #Enable/Disable LPASS support # 0 to disable, 1 to enable gEnableLpassSupport=1 # Whether userspace country code setting shld have priority gCountryCodePriority=1 # Enable or Disable Multi-user MIMO # 1=Enable (default), 0=Disable gEnableMuBformee=1 # Inactivity time (in ms) to end TX Service Period while in IBSS power save mode gIbssTxSpEndInactivityTime=10 ############################################# # TDLS related configurations ############################################# # Enable support for TDLS # 0 - disable # 1 - enable gEnableTDLSSupport=1 # Enable support for Implicit Trigger of TDLS. That is, wlan driver shall # initiate TDLS Discovery towards a peer whenever setup criteria (throughput # and RSSI) is met and then will initiate teardown when teardown criteria # (idle packet count and RSSI) is met. # 0 - disable # 1 - enable gEnableTDLSImplicitTrigger=1 # Enable support for TDLS off-channel operation # 0 - disable # 1 - enable # TDLS off-channel operation will be invoked when there is only one # TDLS connection. gEnableTDLSOffChannel=0 # Tx/Rx Packet threshold for initiating TDLS. # This ini is used to configure the number of Tx/Rx packets during the period of # gTDLSTxStatsPeriod when exceeded, a TDLS Discovery request is triggered. gTDLSTxPacketThreshold=10 # Number of idle packet. # This ini is used to configure the number of Tx/Rx packet, below which # within last gTDLSTxStatsPeriod period is considered as idle condition. gTDLSIdlePacketThreshold=1 # VHT Tx/Rx MCS values # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gVhtRxMCS=2 gVhtTxMCS=2 # VHT Tx/Rx MCS values for 2x2 # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gEnable2x2=1 gVhtRxMCS2x2=2 gVhtTxMCS2x2=2 #IPA config is a bit mask and following are the configurations. #bit0 IPA Enable #bit1 IPA PRE Filter enable #bit2 IPv6 enable #bit3 IPA Resource Manager (RM) enable #bit4 IPA Clock scaling enable #bit5 IPA uC ENABLE #bit6 IPA uC STA ENABLE #bit8 IPA Real Time Debugging gIPAConfig=0x7d # Enable Rx handling options # Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium) # Rx_thread + NAPI = 5 rx_mode=5 # Enable(Tx) fastpath for data traffic. # 1 - enable(default) 0 - disable gEnableFastPath=1 # Enable TCP Segmentation Offload # 1 - enable 0 - disable TSOEnable=1 # Enable Generic Receive Offload # LRO and GRO are exclusive to each other # LRO support is deprecated on latest 4.9(SDM845) kernel # 1 - enable(default) 0 - disable GROEnable=1 # Enable HT MPDU Density # 4 for 2 micro sec ght_mpdu_density=4 # Enable flow steering to enable multiple CEs for Rx flows. # Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs. # Parallel Rx paths. # 1 - enable 0 - disable(default) gEnableFlowSteering=1 # Time in microseconds after which a NAPI poll must yield ce_service_max_yield_time=500 #Maximum number of HTT messages to be processed per NAPI poll ce_service_max_rx_ind_flush=1 # Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND maxMSDUsPerRxInd=8 ################ Datapath feature set End ################ ################ NAN feature set start ################### # Enable NAN discovery (NAN 1.0) # 1 - enable 0 - disable(default) gEnableNanSupport=1 ################ NAN feature set end ##################### hostscan_adaptive_dwell_mode=1 # Create another interface during driver load gEnableConcurrentSTA=wlan1 #Enable/Disable dual MAC feature # 0 - enable DBS # 1 - disable DBS # 2 - disable DBS for connection but keep DBS for scan # 3 - disable DBS for connection but keep DBS scan with async # scan policy disabled # 4 - enable DBS for connection as well as for scan with async # scan policy disabled # 5 - enable DBS for connection but disable dbs for scan. # 6 - enable DBS for connection but disable simultaneous scan from # upper layer (DBS scan remains enabled in FW). gDualMacFeatureDisable=6 #Enable/Disable latency mode # 0 disable # 1 enable wlm_latency_enable=1 # Enable/Disable NUD Tracking within driver gEnableNUDTracking=0 # Configure hardware filter for DTIM mode # The hardware filter is only effective in DTIM mode. # Use this configuration to blanket drop broadcast/multicast packets at the hardware level # without waking up the firmware # # Takes a bitmap of frame types to drop # # 0 = disable feature # 1 = drop all broadcast frames, except ARP (default) # 2 = drop all multicast frames, except ICMPv6 # 3 = drop all broadcast and multicast frames, except ARP and ICMPv6 gHwFilterMode=0 # Enables SNR Monitoring # This ini is used to set default snr monitor gEnableSNRMonitoring=1 # Control to enable TCP limit output byte # This ini is used to enable dynamic configuration of TCP limit output bytes # tcp_limit_output_bytes param. # Enabling this will let driver post message to cnss-daemon, # accordingly cnss-daemon will modify the tcp_limit_output_bytes. gTcpLimitOutputEnable=0 # Enable Target Wake Time support. # This ini is used to enable or disable TWT support. enable_twt=0 # For NLO/PNO, enable MAWC based scan # Enable/Disable the Motion Aided Wireless Connectivity based NLO using this parameter mawc_nlo_enabled=0 # Force 1x1 when connecting to certain peer # This INI when enabled will force 1x1 connection with certain peer. gForce1x1Exception=0 # Enable/disable oce feature for STA # This ini is used to enable/disable oce feature for STA oce_sta_enable=1 # Enable/disable oce feature for SAP # This ini is used to enable/disable oce feature for SAP oce_sap_enable=0 #Enable/disable FILS discovery for SAP oce_enable_fils_discovery_sap=0 # Set probe request rate # This ini is used to set probe request rate to 5.5Mbps as per OCE requirement in 2.4G band oce_enable_probe_req_rate=0 #Enable/disable probe request deferral as per OCE spec oce_enable_probe_req_deferral=0 # HE caps Weightage to calculate best candidate # This ini is used to increase/decrease HE caps weightage in best candidate selection. # If AP supports HE caps, AP will get additional weightage with this param. # Weightage will be given only if dot11mode is HE capable. he_caps_weightage=0 # PCL Weightage to calculate best candidate # This ini is used to increase/decrease PCL weightage in best candidate selection. # If some APs are in PCL list, those AP will get addition weightage. pcl_weightage=10 # Enable/disable esp feature # This ini is used to enable/disable ESP(Estimated service parameters) IE parsing and decides # whether firmware will include this in its scoring algo. enable_esp_for_roam=0 # Bitmask to enable 11k offload to FW. # This ini is used to set which of the 11k features is offloaded to FW # Currently Neighbor Report Request is supported for offload and is enabled by default. # B0: Offload 11k neighbor report requests # B1-B31: Reserved 11k_offload_enable_bitmask=0 # Set channel selection logic for different concurrency combinations to DBS or inter band MCC. # Default is DBS for STA+STA and STA+P2P. # 0 - inter-band MCC # 1 - DBS # # BIT 0: STA+STA # BIT 1: STA+P2P # BIT 2-31: Reserved channel_select_logic_conc=0 # Configure BTM # Bit 0: Enable/Disable the BTM offload. Set this to 1 will enable and 0 will disable BTM offload. # BIT 2, 1: Action on non matching candidate with cache. If a BTM request is received from AP # then the candidate AP's may/may-not be present in the firmware scan cache. # Based on below config firmware will decide whether to forward BTM frame to host or # consume with firmware and proceed with Roaming to candidate AP. # # 00 scan and consume # 01 no scan and forward to host # 10, 11 reserved # BIT 5, 4, 3: Roaming handoff decisions on multiple candidates match # 000 match if exact BSSIDs are found # 001 match if at least one top priority BSSID only # 010, 011, 100, 101, 110, 111 reserved # BIT 6: Set this to 1 will send BTM query frame and 0 not sent. # BIT 7-31: Reserved btm_offload_config=1473 btm_disassoc_timer_threshold=10000 minimum_btm_candidate_score=0 roam_candidate_validity_timer=0 #Timer waiting for interface up from the upper layer gInterfaceChangeWait=2000 # Set external ACS Policy to Mandatory acs_policy=1 # Set Modulated Dtim gEnableModulatedDTIM=2 # Enable NAN datapath genable_nan_datapath=1 # Set MaxLIModulate Dtim gMaxLIModulatedDTIM=6 # Used for ignore peer infrormation gIgnorePeerErpInfo=1 # DBS Scan Selection gdbs_scan_selection=5,4,1,16,4,1 # 0 - Disallow STA+SAP SCC on LTE coex channel # 1 - Allow STA+SAP SCC on LTE coex channel g_sta_sap_scc_on_lte_coex_chan=1 # Tx Chain Mask for CCK gCckChainMaskEnable=1 # Tx Chain Mask for 1SS gTxChainMask1ss=0 # TPC power gSelfGenFrmPwr=3 # Enable LFR3 subnet detection gLFRSubnetDetectionEnable=0 #Enable APF in Active mode gActiveUcBpfMode=2 # Control MC/BC active APF mode gActiveMcBcBpfMode=1 # Enable or disable Probe Req Information Element whitelist. When enabled, IEs corresponding to bits # set in bitmaps are allowed in probe request, all others removed while device is unassociated # with an AP # 1=Enable, 0=Disable (default) g_enable_probereq_whitelist_ies=1 # ie bitmap examples: = [] # g_probe_req_ie_bitmap_0=0x80000009 #[0, 3, 31] # g_probe_req_ie_bitmap_0=0x00000000 #[] (default) # g_probe_req_ie_bitmap_1=0x80000009 #[32, 35, 63] g_probe_req_ie_bitmap_0=0x0000000B g_probe_req_ie_bitmap_1=0x00040000 # g_probe_req_ie_bitmap_2=0x00000000 # g_probe_req_ie_bitmap_3=0x00000000 # g_probe_req_ie_bitmap_4=0x00000000 # g_probe_req_ie_bitmap_5=0x00000000 g_probe_req_ie_bitmap_6=0x20000000 # g_probe_req_ie_bitmap_7=0x00000000 # Used to specify vendor specific OUIs gProbeReqOUIs=0050F208 # enable 11d in world mode enable_11d_in_world_mode=1 # WLM flags setting for low level wlm_latency_flags_low=0xc08 #Enable/Disable chain selection optimization for one chain dtim #Min: 0 #MAX: 30 gEnableDTIMSelectionDiversity=3 # Enable/Disable rtt sta mac randomization enable_rtt_mac_randomization=1 # Set max time for active 2G channel scan active_max_channel_time_2g=40 # To config roaming scan policy roaming_scan_policy=1 # Config DPTRACE gDptraceConfig=1,6,2,126 # Enable/Disable peer unmap confirmation support in Host gEnablePeerUnmapConfSupport=1 # Enable/Disable separate wifi aware interface nan_separate_iface_support=1 # Config Thermal mitigation gThrottleDutyCycleLevel0=0 gThrottleDutyCycleLevel1=0 gThrottleDutyCycleLevel2=10 gThrottleDutyCycleLevel3=30 gThrottleDutyCycleLevel4=50 gThrottleDutyCycleLevel5=70 # Enable/Disable conversion from SARV1 to SARV2 gEnableSARV1toSARV2=1 #This ini is used to enable/disable ESE feature EseEnabled=1 # Configure max number of ndi host supports ndi_max_support=2 # Use wake lock during user scan wake_lock_in_user_scan=1 # To address an interop issue with a particular AP # Used to specify action OUIs to reconnect when assoc timeout gActionOUIReconnAssocTimeout=00E04C 00 01 # Limit to send request to the firmware at most once in a second nb_commands_interval=1 # This ini is used to enable/disable the HW assist feature in FW g_disable_hw_assist=1 END # Note: Configuration parser would not read anything past the END marker