diff options
author | Thierry Strudel <tstrudel@google.com> | 2015-05-07 23:25:21 -0700 |
---|---|---|
committer | Thierry Strudel <tstrudel@google.com> | 2015-05-20 10:09:56 -0700 |
commit | f9621af82db2b5add2abb34e167352a50589d88f (patch) | |
tree | c80f363be7fa7cee69190f6c06cf12f1fd7320a1 /nfc | |
parent | f062618ee311518e7de43d2d87cf82c88ff6a40e (diff) | |
download | bullhead-f9621af82db2b5add2abb34e167352a50589d88f.tar.gz |
bullhead: enable NFC HAL for NXP pn548
Change-Id: Id64b41a4e7808bd92aaa34b3fa446e76a6613b0d
Diffstat (limited to 'nfc')
-rw-r--r-- | nfc/libnfc-brcm.conf | 385 | ||||
-rw-r--r-- | nfc/libnfc-nxp.conf | 265 |
2 files changed, 650 insertions, 0 deletions
diff --git a/nfc/libnfc-brcm.conf b/nfc/libnfc-brcm.conf new file mode 100644 index 0000000..66159e8 --- /dev/null +++ b/nfc/libnfc-brcm.conf @@ -0,0 +1,385 @@ +###################### Start of libnfc-brcm.conf ####################### + +############################################################################### +# Application options +APPL_TRACE_LEVEL=0xFF +PROTOCOL_TRACE_LEVEL=0xFFFFFFFF + +############################################################################### +# performance measurement +# Change this setting to control how often USERIAL log the performance (throughput) +# data on read/write/poll +# defailt is to log performance dara for every 100 read or write +#REPORT_PERFORMANCE_MEASURE=100 + +############################################################################### +# File used for NFA storage +NFA_STORAGE="/data/nfc" + +############################################################################### +# Snooze Mode Settings +# +# By default snooze mode is enabled. Set SNOOZE_MODE_CFG byte[0] to 0 +# to disable. +# +# If SNOOZE_MODE_CFG is not provided, the default settings are used: +# They are as follows: +# 8 Sleep Mode (0=Disabled 1=UART 8=SPI/I2C) +# 0 Idle Threshold Host +# 0 Idle Threshold HC +# 0 NFC Wake active mode (0=ActiveLow 1=ActiveHigh) +# 1 Host Wake active mode (0=ActiveLow 1=ActiveHigh) +# +#SNOOZE_MODE_CFG={08:00:00:00:01} + +############################################################################### +# Insert a delay in milliseconds after NFC_WAKE and before write to NFCC +#NFC_WAKE_DELAY=20 + +############################################################################### +# Various Delay settings (in ms) used in USERIAL +# POWER_ON_DELAY +# Delay after turning on chip, before writing to transport (default 300) +# PRE_POWER_OFF_DELAY +# Delay after deasserting NFC-Wake before turn off chip (default 0) +# POST_POWER_OFF_DELAY +# Delay after turning off chip, before USERIAL_close returns (default 0) +# +#POWER_ON_DELAY=300 +#PRE_POWER_OFF_DELAY=0 +#POST_POWER_OFF_DELAY=0 + +############################################################################### +# Maximum time (ms) to wait for RESET NTF after setting REG_PU to high +# The default is 1000. +#NFCC_ENABLE_TIMEOUT=0 + +############################################################################### +# LPTD mode configuration +# byte[0] is the length of the remaining bytes in this value +# if set to 0, LPTD params will NOT be sent to NFCC (i.e. disabled). +# byte[1] is the param id it should be set to B9. +# byte[2] is the length of the LPTD parameters +# byte[3] indicates if LPTD is enabled +# if set to 0, LPTD will be disabled (parameters will still be sent). +# byte[4-n] are the LPTD parameters. +# By default, LPTD is enabled and default settings are used. +# See nfc_hal_dm_cfg.c for defaults +#LPTD_CFG={23:B9:21:01:02:FF:FF:04:A0:0F:40:00:80:02:02:10:00:00:00:31:0C:30:00:00:00:00:00:00:00:00:00:00:00:00:00:00} + +############################################################################### +# Startup Configuration (100 bytes maximum) +# +# For the 0xCA parameter, byte[9] (marked by 'AA') is for UICC0, and byte[10] (marked by BB) is +# for UICC1. The values are defined as: +# 0 : UICCx only supports ISO_DEP in low power mode. +# 2 : UICCx only supports Mifare in low power mode. +# 3 : UICCx supports both ISO_DEP and Mifare in low power mode. +# +# AA BB +#NFA_DM_START_UP_CFG={1F:CB:01:01:A5:01:01:CA:14:00:00:00:00:06:E8:03:00:00:00:00:00:00:00:00:00:00:00:00:00:80:01:01} + +############################################################################### +# Startup Vendor Specific Configuration (100 bytes maximum); +# byte[0] TLV total len = 0x5 +# byte[1] NCI_MTS_CMD|NCI_GID_PROP = 0x2f +# byte[2] NCI_MSG_FRAME_LOG = 0x9 +# byte[3] 2 +# byte[4] 0=turn off RF frame logging; 1=turn on +# byte[5] 0=turn off SWP frame logging; 1=turn on +# NFA_DM_START_UP_VSC_CFG={05:2F:09:02:01:01} + +############################################################################### +# Antenna Configuration - This data is used when setting 0xC8 config item +# at startup (before discovery is started). If not used, no value is sent. +# +# The settings for this value are documented here: +# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/ +# Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx +# This document is maintained by Paul Forshaw. +# +# The values marked as ?? should be tweaked per antenna or customer/app: +# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04} +# array[0] = 0x20 is length of the payload from array[1] to the end +# array[1] = 0xC8 is PREINIT_DSP_CFG +#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04} + +############################################################################### +# Configure crystal frequency when internal LPO can't detect the frequency. +#XTAL_FREQUENCY=0 +############################################################################### +# Configure the default Destination Gate used by HCI (the default is 4, which +# is the ETSI loopback gate. +NFA_HCI_DEFAULT_DEST_GATE=0xF0 + +############################################################################### +# Configure the single default SE to use. The default is to use the first +# SE that is detected by the stack. This value might be used when the phone +# supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use +# one of them (e.g. 0xF4). +#ACTIVE_SE=0xF3 + +############################################################################### +# Configure the default NfcA/IsoDep techology and protocol route. Can be +# either a secure element (e.g. 0xF4) or the host (0x00) +#DEFAULT_ISODEP_ROUTE=0x00 + +############################################################################### +# Configure the NFC Extras to open and use a static pipe. If the value is +# not set or set to 0, then the default is use a dynamic pipe based on a +# destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value +# for each UICC (where F3="UICC0" and F4="UICC1") +#NFA_HCI_STATIC_PIPE_ID_F3=0x70 +#NFA_HCI_STATIC_PIPE_ID_01=0x19 +NFA_HCI_STATIC_PIPE_ID_C0=0x19 +############################################################################### +# When disconnecting from Oberthur secure element, perform a warm-reset of +# the secure element to deselect the applet. +# The default hex value of the command is 0x3. If this variable is undefined, +# then this feature is not used. +#OBERTHUR_WARM_RESET_COMMAND=0x03 + +############################################################################### +# Force UICC to only listen to the following technology(s). +# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. +# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | NFA_TECHNOLOGY_MASK_F +UICC_LISTEN_TECH_MASK=0x07 + +############################################################################### +# Force HOST listen feature enable or disable. +# 0: Disable +# 1: Enable +HOST_LISTEN_ENABLE=0x01 + +############################################################################### +# Enabling/Disabling Forward functionality +# Disable 0x00 +# Enable 0x01 +NXP_FWD_FUNCTIONALITY_ENABLE=0x01 + +############################################################################### +# Allow UICC to be powered off if there is no traffic. +# Timeout is in ms. If set to 0, then UICC will not be powered off. +#UICC_IDLE_TIMEOUT=30000 +UICC_IDLE_TIMEOUT=0 + +############################################################################### +# AID for Empty Select command +# If specified, this AID will be substituted when an Empty SELECT command is +# detected. The first byte is the length of the AID. Maximum length is 16. +AID_FOR_EMPTY_SELECT={08:A0:00:00:01:51:00:00:00} +############################################################################### +# Maximum Number of Credits to be allowed by the NFCC +# This value overrides what the NFCC specifices allowing the host to have +# the control to work-around transport limitations. If this value does +# not exist or is set to 0, the NFCC will provide the number of credits. +MAX_RF_DATA_CREDITS=1 + +############################################################################### +# This setting allows you to disable registering the T4t Virtual SE that causes +# the NFCC to send PPSE requests to the DH. +# The default setting is enabled (i.e. T4t Virtual SE is registered). +#REGISTER_VIRTUAL_SE=1 + +############################################################################### +# When screen is turned off, specify the desired power state of the controller. +# 0: power-off-sleep state; DEFAULT +# 1: full-power state +# 2: screen-off card-emulation (CE4/CE3/CE1 modes are used) +SCREEN_OFF_POWER_STATE=1 + +############################################################################### +# Firmware patch file +# If the value is not set then patch download is disabled. +#FW_PATCH="/vendor/firmware/bcm2079x_firmware.ncd" + +############################################################################### +# Firmware pre-patch file (sent before the above patch file) +# If the value is not set then pre-patch is not used. +#FW_PRE_PATCH="/vendor/firmware/bcm2079x_pre_firmware.ncd" + +############################################################################### +# Firmware patch format +# 1 = HCD +# 2 = NCD (default) +#NFA_CONFIG_FORMAT=2 + +############################################################################### +# SPD Debug mode +# If set to 1, any failure of downloading a patch will trigger a hard-stop +#SPD_DEBUG=0 + +############################################################################### +# SPD Max Retry Count +# The number of attempts to download a patch before giving up (defualt is 3). +# Note, this resets after a power-cycle. +#SPD_MAX_RETRY_COUNT=3 + +############################################################################### +# transport driver +# +# TRANSPORT_DRIVER=<driver> +# +# where <driver> can be, for example: +# "/dev/ttyS" (UART) +# "/dev/bcmi2cnfc" (I2C) +# "hwtun" (HW Tunnel) +# "/dev/bcmspinfc" (SPI) +# "/dev/btusb0" (BT USB) +#TRANSPORT_DRIVER="/dev/bcm2079x-i2c" + +############################################################################### +# power control driver +# Specify a kernel driver that support ioctl commands to control NFC_EN and +# NFC_WAKE gpio signals. +# +# POWER_CONTRL_DRIVER=<driver> +# where <driver> can be, for example: +# "/dev/nfcpower" +# "/dev/bcmi2cnfc" (I2C) +# "/dev/bcmspinfc" (SPI) +# i2c and spi driver may be used to control NFC_EN and NFC_WAKE signal +#POWER_CONTROL_DRIVER="/dev/bcm2079x-i2c" + +############################################################################### +# I2C transport driver options +# Mako does not support 10-bit I2C addresses +# Revert to 7-bit address +#BCMI2CNFC_ADDRESS=0x77 + +############################################################################### +# I2C transport driver try to read multiple packets in read() if data is available +# remove the comment below to enable this feature +#READ_MULTIPLE_PACKETS=1 + +############################################################################### +# SPI transport driver options +#SPI_NEGOTIATION={0A:F0:00:01:00:00:00:FF:FF:00:00} + +############################################################################### +# UART transport driver options +# +# PORT=1,2,3,... +# BAUD=115200, 19200, 9600, 4800, +# DATABITS=8, 7, 6, 5 +# PARITY="even" | "odd" | "none" +# STOPBITS="0" | "1" | "1.5" | "2" + +#UART_PORT=2 +#UART_BAUD=115200 +#UART_DATABITS=8 +#UART_PARITY="none" +#UART_STOPBITS="1" + +############################################################################### +# Insert a delay in microseconds per byte after a write to NFCC. +# after writing a block of data to the NFCC, delay this an amopunt of time before +# writing next block of data. the delay is calculated as below +# NFC_WRITE_DELAY * (number of byte written) / 1000 milliseconds +# e.g. after 259 bytes is written, delay (259 * 20 / 1000) 5 ms before next write +#NFC_WRITE_DELAY=20 + +############################################################################### +# Maximum Number of Credits to be allowed by the NFCC +# This value overrides what the NFCC specifices allowing the host to have +# the control to work-around transport limitations. If this value does +# not exist or is set to 0, the NFCC will provide the number of credits. +MAX_RF_DATA_CREDITS=1 + +############################################################################### +# Default poll duration (in ms) +# The defualt is 500ms if not set (see nfc_target.h) +#NFA_DM_DISC_DURATION_POLL=333 +############################################################################### +# Antenna Configuration - This data is used when setting 0xC8 config item +# at startup (before discovery is started). If not used, no value is sent. +# +# The settings for this value are documented here: +# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/ +# Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx +# This document is maintained by Paul Forshaw. +# +# The values marked as ?? should be tweaked per antenna or customer/app: +# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04} +# array[0] = 0x20 is length of the payload from array[1] to the end +# array[1] = 0xC8 is PREINIT_DSP_CFG +#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04} + + +############################################################################### +# Choose the presence-check algorithm for type-4 tag. If not defined, the default value is 1. +# 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm +# 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block +# 2 NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate +# 3 NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0 +# 4 NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3 +#PRESENCE_CHECK_ALGORITHM=0 + +############################################################################### +# Force tag polling for the following technology(s). +# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. +# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | +# NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ISO15693 | +# NFA_TECHNOLOGY_MASK_B_PRIME | NFA_TECHNOLOGY_MASK_KOVIO | +# NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE. +# +# Notable bits: +# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */ +# NFA_TECHNOLOGY_MASK_B 0x02 /* NFC Technology B */ +# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */ +# NFA_TECHNOLOGY_MASK_ISO15693 0x08 /* Proprietary Technology */ +# NFA_TECHNOLOGY_MASK_KOVIO 0x20 /* Proprietary Technology */ +# NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */ +# NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */ +POLLING_TECH_MASK=0xCF + +############################################################################### +# Force P2P to only listen for the following technology(s). +# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. +# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_F | +# NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE +# +# Notable bits: +# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */ +# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */ +# NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */ +# NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */ +P2P_LISTEN_TECH_MASK=0xC5 + +PRESERVE_STORAGE=0x01 + +############################################################################### +# Override the stack default for NFA_EE_MAX_EE_SUPPORTED set in nfc_target.h. +# The value is set to 3 by default as it assumes we will discover 0xF2, +# 0xF3, and 0xF4. If a platform will exclude and SE, this value can be reduced +# so that the stack will not wait any longer than necessary. + +# Maximum EE supported number +# NXP PN547C2 0x02 +# NXP PN65T 0x03 +# NXP PN548C2 0x02 +# NXP PN66T 0x03 +NFA_MAX_EE_SUPPORTED=0x03 + +############################################################################### +# NCI Hal Module name +NCI_HAL_MODULE="nfc_nci" + +############################################################################## +# Deactivate notification wait time out in seconds used in ETSI Reader mode +# 0 - Infinite wait +NFA_DM_DISC_NTF_TIMEOUT=100 + +############################################################################### +# AID_MATCHING constants +# AID_MATCHING_EXACT_ONLY 0x00 +# AID_MATCHING_EXACT_OR_PREFIX 0x01 +# AID_MATCHING_PREFIX_ONLY 0x02 +AID_MATCHING_MODE=0x01 + +############################################################################### +# Preferred Secure Element for Technology based routing +# eSE 0x01 +# UICC 0x02 + +NXP_PRFD_TECH_SE=0x01 diff --git a/nfc/libnfc-nxp.conf b/nfc/libnfc-nxp.conf new file mode 100644 index 0000000..e21b23d --- /dev/null +++ b/nfc/libnfc-nxp.conf @@ -0,0 +1,265 @@ +## This file is used by NFC NXP NCI HAL(external/libnfc-nci/halimpl/pn54x) +## and NFC Service Java Native Interface Extensions (packages/apps/Nfc/nci/jni/extns/pn54x) + +############################################################################### +# Application options +# Logging Levels +# NXPLOG_DEFAULT_LOGLEVEL 0x01 +# ANDROID_LOG_DEBUG 0x03 +# ANDROID_LOG_WARN 0x02 +# ANDROID_LOG_ERROR 0x01 +# ANDROID_LOG_SILENT 0x00 +# +NXPLOG_EXTNS_LOGLEVEL=0x03 +NXPLOG_NCIHAL_LOGLEVEL=0x03 +NXPLOG_NCIX_LOGLEVEL=0x03 +NXPLOG_NCIR_LOGLEVEL=0x03 +NXPLOG_FWDNLD_LOGLEVEL=0x03 +NXPLOG_TML_LOGLEVEL=0x03 + +############################################################################### +# Extension for Mifare reader enable +MIFARE_READER_ENABLE=0x01 + +############################################################################### +# Vzw Feature enable +VZW_FEATURE_ENABLE=0x01 + +############################################################################### +# File location for Firmware +#FW_STORAGE="/vendor/firmware/libpn548_fw.so" + +############################################################################### +# System clock source selection configuration +#define CLK_SRC_XTAL 1 +#define CLK_SRC_PLL 2 + +NXP_SYS_CLK_SRC_SEL=0x01 + +############################################################################### +# System clock frequency selection configuration +#define CLK_FREQ_13MHZ 1 +#define CLK_FREQ_19_2MHZ 2 +#define CLK_FREQ_24MHZ 3 +#define CLK_FREQ_26MHZ 4 +#define CLK_FREQ_38_4MHZ 5 +#define CLK_FREQ_52MHZ 6 + +NXP_SYS_CLK_FREQ_SEL=0x02 + +############################################################################### +# The timeout value to be used for clock request acknowledgment +# min value = 0x01 to max = 0x1A + +NXP_SYS_CLOCK_TO_CFG=0x01 + +############################################################################### +# NXP proprietary settings +NXP_ACT_PROP_EXTN={2F, 02, 00} + +############################################################################### +# NFC forum profile settings +NXP_NFC_PROFILE_EXTN={20, 02, 05, 01, A0, 44, 01, 00} + +############################################################################### +# NFCC Configuration Control +# Allow NFCC to manage RF Config 0x01 +# Don't allow NFCC to manage RF Config 0x00 +NXP_NFC_MERGE_RF_PARAMS={20, 02, 04, 01, 85, 01, 01} + +############################################################################### +# Standby enable settings +#NXP_CORE_STANDBY={2F, 00, 01, 01} + +############################################################################### +# NXP TVDD configurations settings +# Allow NFCC to configure External TVDD, There are currently three +#configurations (1, 2 and 3) are supported, out of them only one can be +#supported. + +NXP_EXT_TVDD_CFG=0x01 + +############################################################################### +#config1:SLALM, 3.3V for both RM and CM +NXP_EXT_TVDD_CFG_1={20, 02, 0B, 02, A0, 66, 01, 00, A0, 0E, 03, 02, 09, 00} + +############################################################################### +#config2: use DCDC in CE, use Tx_Pwr_Req, set CFG2 mode, SLALM, +#monitoring 5V from DCDC, 4.7V for both RM and CM, DCDCWaitTime=4.2ms +NXP_EXT_TVDD_CFG_2={20, 02, 0B, 02, A0, 66, 01, 00, A0, 0E, 03, 56, 64, 0A} + +############################################################################### +#config3: use DCDC in CE, use Tx_Pwr_Req, SLALM, monitoring 5V from DCDC, +#DCDCWaitTime=4.2ms +NXP_EXT_TVDD_CFG_3={20, 02, 0B, 02, A0, 66, 01, 01, A0, 0E, 03, 52, 64, 0A} + +############################################################################### +# NXP RF configuration ALM/PLM settings +# This section needs to be updated with the correct values based on the platform +#NXP_RF_CONF_BLK_1={ +#} + +############################################################################### +# NXP RF configuration ALM/PLM settings +# This section needs to be updated with the correct values based on the platform +#NXP_RF_CONF_BLK_2={ +#} + +############################################################################### +# NXP RF configuration ALM/PLM settings +# This section needs to be updated with the correct values based on the platform +#NXP_RF_CONF_BLK_3={ +#} + +############################################################################### +# NXP RF configuration ALM/PLM settings +# This section needs to be updated with the correct values based on the platform +#NXP_RF_CONF_BLK_4={ +#} + +############################################################################### +# NXP RF configuration ALM/PLM settings +# This section needs to be updated with the correct values based on the platform +#NXP_RF_CONF_BLK_5={ +#} + +############################################################################### +# NXP RF configuration ALM/PLM settings +# This section needs to be updated with the correct values based on the platform +#NXP_RF_CONF_BLK_6={ +#} + +############################################################################### +# Core configuration extensions +# It includes +# Wired mode settings A0ED, A0EE +# Tag Detector A040, A041, A043 +# Low Power mode A007 +# Clock settings A002, A003 +# PbF settings A008 +NXP_CORE_CONF_EXTN={20, 02, 15, 05, + A0, EC, 01, 01, + A0, ED, 01, 00, + A0, 5E, 01, 01, + A0, 40, 01, 01, + A0, DD, 01, 2D + } + +############################################################################### +# Core configuration rf field filter settings to enable set 01 ,to disable set to 00 last bit +NXP_CORE_RF_FIELD={ 20, 02, 05, 01, A0, 62, 01, 01 + } + +############################################################################### +# To enable i2c fragmentation set i2c fragmentation enable 0x01 to disable set to 0x00 +NXP_I2C_FRAGMENTATION_ENABLED=0x00 + +############################################################################### +# Core configuration settings +NXP_CORE_CONF={ 20, 02, 2B, 0D, + 28, 01, 00, + 21, 01, 00, + 30, 01, 08, + 31, 01, 03, + 33, 04, 01, 02, 03, 04, + 54, 01, 06, + 50, 01, 02, + 5B, 01, 00, + 60, 01, 0E, + 80, 01, 01, + 81, 01, 01, + 82, 01, 0E, + 18, 01, 01 + } + +############################################################################### +# Mifare Classic Key settings +#NXP_CORE_MFCKEY_SETTING={20, 02, 25,04, A0, 51, 06, A0, A1, A2, A3, A4, A5, +# A0, 52, 06, D3, F7, D3, F7, D3, F7, +# A0, 53, 06, FF, FF, FF, FF, FF, FF, +# A0, 54, 06, 00, 00, 00, 00, 00, 00} + +############################################################################### +# Default SE Options +# No secure element 0x00 +# eSE 0x01 +# UICC 0x02 + +NXP_DEFAULT_SE=0x03 + +############################################################################### +#Enable SWP full power mode when phone is power off +NXP_SWP_FULL_PWR_ON=0x00 + +############################################################################### +#### Select the CHIP #### +#PN547C2 0x01 +#PN65T 0x02 +#PN548AD 0x03 +#PN66T 0x04 + +NXP_NFC_CHIP=0x03 + +############################################################################### +# CE when Screen state is locked +# Disable 0x00 +# Enable 0x01 +NXP_CE_ROUTE_STRICT_DISABLE=0x01 + +############################################################################### +#Timeout in secs to get NFCEE Discover notification +NXP_DEFAULT_NFCEE_DISC_TIMEOUT=20 + +NXP_DEFAULT_NFCEE_TIMEOUT=0x06 + +############################################################################### +#Timeout in secs +NXP_SWP_RD_START_TIMEOUT=0x0A + +############################################################################### +#Timeout in secs +NXP_SWP_RD_TAG_OP_TIMEOUT=0x01 + +############################################################################### +#Set the default AID route Location : +#This settings will be used when application does not set this parameter +# host 0x00 +# eSE 0x01 +# UICC 0x02 +DEFAULT_AID_ROUTE=0x00 + +############################################################################### +#Set the Mifare Desfire route Location : +#This settings will be used when application does not set this parameter +# host 0x00 +# eSE 0x01 +# UICC 0x02 +DEFAULT_DESFIRE_ROUTE=0x02 + +############################################################################### +#Set the Mifare CLT route Location : +#This settings will be used when application does not set this parameter +# host 0x00 +# eSE 0x01 +# UICC 0x02 +DEFAULT_MIFARE_CLT_ROUTE=0x02 + +############################################################################### +# AID Matching platform options +# AID_MATCHING_L 0x01 +# AID_MATCHING_K 0x02 +AID_MATCHING_PLATFORM=0x01 + +############################################################################### +#CHINA_TIANJIN_RF_SETTING +#Enable 0x01 +#Disable 0x00 +NXP_CHINA_TIANJIN_RF_ENABLED=0x01 + +############################################################################### +#SWP_SWITCH_TIMEOUT_SETTING +# Allowed range of swp timeout setting is 0x00 to 0x3C [0 - 60]. +# Timeout in milliseconds, for example +# No Timeout 0x00 +# 10 millisecond timeout 0x0A +NXP_SWP_SWITCH_TIMEOUT=0x0A |