initial mako support

Change-Id: I5c364ced5b26c5c6d8f51f87146d5ec4484586ae
Signed-off-by: Iliyan Malchev <malchev@google.com>

1 files changed, 189 insertions, 0 deletions

diff --git a/WCNSS_qcom_cfg.ini b/WCNSS_qcom_cfg.ini
new file mode 100755
index 0000000..100ec5d
--- /dev/null
+++ b/WCNSS_qcom_cfg.ini
@@ -0,0 +1,189 @@
+# This file allows user to override the factory
+# defaults for the WLAN Driver
+
+# Enable IMPS or not
+gEnableImps=1
+
+# Enable/Disable Idle Scan
+gEnableIdleScan=0
+
+# Increase sleep duration (seconds) during IMPS
+# 0 implies no periodic wake up from IMPS. Periodic wakeup is 
+# unnecessary if Idle Scan is disabled.
+gImpsModSleepTime=0
+
+# Enable BMPS or not
+gEnableBmps=1
+
+# Enable suspend or not
+# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
+gEnableSuspend=3
+
+# Phy Mode (auto, b, g, n, etc)
+gDot11Mode=0
+
+# Handoff Enable(1) Disable(0)
+gEnableHandoff=0
+
+# CSR Roaming Enable(1) Disable(0)
+gRoamingTime=0
+
+# Assigned MAC Addresses - This will be used until NV items are in place
+# Each byte of MAC address is represented in Hex format as XX
+Intf0MacAddress=000AF58989FF
+Intf1MacAddress=000AF58989FE
+Intf2MacAddress=000AF58989FD
+Intf3MacAddress=000AF58989FC
+
+# UAPSD service interval for VO,VI, BE, BK traffic
+InfraUapsdVoSrvIntv=0
+InfraUapsdViSrvIntv=0
+InfraUapsdBeSrvIntv=0
+InfraUapsdBkSrvIntv=0
+
+# Disable RSSI FW filtering
+gEnableFWRssiMonitoring=0
+
+# Make 1x1 the default antenna configuration
+gNumRxAnt=1
+
+# Beacon filtering frequency (unit in beacon intervals)
+gNthBeaconFilter=50
+
+# Enable WAPI or not
+# WAPIIsEnabled=0
+
+# Flags to filter Mcast abd Bcast RX packets.
+# Value 0: No filtering, 1: Filter all Multicast.
+# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
+McastBcastFilter=3
+
+#Flag to enable HostARPOffload feature or not
+hostArpOffload=0
+
+#SoftAP Related Parameters
+# AP MAc addr
+gAPMacAddr=000AF58989EF
+
+# 802.11n Protection flag
+gEnableApProt=1
+
+#Enable OBSS protection
+gEnableApOBSSProt=0
+
+#Enable/Disable UAPSD for SoftAP
+gEnableApUapsd=1
+
+# Fixed Rate
+gFixedRate=0
+
+# Maximum Tx power
+# gTxPowerCap=30
+
+# Fragmentation Threshold
+# gFragmentationThreshold=2346
+
+# RTS threshold
+RTSThreshold=2347
+
+# Intra-BSS forward
+gDisableIntraBssFwd=0
+
+# WMM Enable/Disable
+WmmIsEnabled=0
+
+# 802.11d support
+g11dSupportEnabled=1
+
+# CCX Support and fast transition
+CcxEnabled=0
+FastTransitionEnabled=0
+ImplicitQosIsEnabled=1
+gNeighborScanTimerPeriod=200
+
+gNeighborLookupThreshold=50
+gNeighborReassocThreshold=55
+
+gNeighborScanChannelList=1,11,36,64
+gNeighborScanChannelMinTime=20
+gNeighborScanChannelMaxTime=30
+gMaxNeighborReqTries=3
+
+# SAP Country code
+# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
+# Example
+#   US Indoor, USI
+#   Korea Outdoor, KRO
+#   Japan without optional byte, JP
+#   France without optional byte, FR
+#gAPCntryCode=USI
+
+#Short Guard Interval Enable/disable
+gShortGI20Mhz=1
+gShortGI40Mhz=1
+
+#Auto Shutdown  Value in seconds. A value of 0 means Auto shutoff is disabled
+gAPAutoShutOff=0
+
+# SAP auto channel selection configuration
+# 0 = disable auto channel selection
+# 1 = enable auto channel selection, channel provided by supplicant will be ignored
+gApAutoChannelSelection=0
+
+# Listen Energy Detect Mode Configuration
+# Valid values 0-128
+# 128 means disable Energy Detect feature
+# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
+# 10-128 are reserved.
+# The EDET threshold mapping is as follows in 3dB step:
+# 0 = -60 dBm
+# 1 = -63 dBm
+# 2 = -66 dBm
+# ...
+# 7 = -81 dBm
+# 8 = -84 dBm
+# 9 = -87 dBm
+# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
+#
+#  Range Loss  (dB)  =  EDET threshold level (dBm) + 97 dBm.
+#
+gEnablePhyAgcListenMode=128
+
+#Preferred channel to start BT AMP AP mode (0 means, any channel)
+BtAmpPreferredChannel=0
+
+#Preferred band (both or 2.4 only or 5 only)
+BandCapability=0
+
+#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
+enableBeaconEarlyTermination=0
+beaconEarlyTerminationWakeInterval=3
+
+#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
+gEnableBtAmp=1
+
+#SOFTAP Channel Range selection 
+gAPChannelSelectStartChannel=1
+gAPChannelSelectEndChannel=11
+
+#SOFTAP Channel Range selection Operating band
+# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
+gAPChannelSelectOperatingBand=0
+
+#Enable Keep alive with non-zero period value
+#gStaKeepAlivePeriod = 30
+
+#If set will start with active scan after driver load, otherwise will start with
+#passive scan to find out the domain
+gEnableBypass11d=1
+
+#If set to 0, will not scan DFS channels
+gEnableDFSChnlScan=1
+
+# Enable logp/SSR
+gEnableLogp=1
+
+# Enable Automatic Tx Power control
+gEnableAutomaticTxPowerControl=1
+END
+# Note: Configuration parser would not read anything past the END marker