1 files changed, 0 insertions, 132 deletions
diff --git a/OvmfPkg/ResetVector/SerialDebug.asm b/OvmfPkg/ResetVector/SerialDebug.asm
deleted file mode 100644
index 8c2ffc66d..000000000
--- a/OvmfPkg/ResetVector/SerialDebug.asm
+++ /dev/null
@@ -1,132 +0,0 @@
-;------------------------------------------------------------------------------
-; @file
-; Serial port debug support macros
-;
-; Copyright (c) 2008 - 2009, Intel Corporation
-; All rights reserved. This program and the accompanying materials
-; are licensed and made available under the terms and conditions of the BSD License
-; which accompanies this distribution.  The full text of the license may be found at
-; http://opensource.org/licenses/bsd-license.php
-;
-; THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
-; WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
-;
-;------------------------------------------------------------------------------
-
-;//---------------------------------------------
-;// UART Register Offsets
-;//---------------------------------------------
-%define BAUD_LOW_OFFSET         0x00
-%define BAUD_HIGH_OFFSET        0x01
-%define IER_OFFSET              0x01
-%define LCR_SHADOW_OFFSET       0x01
-%define FCR_SHADOW_OFFSET       0x02
-%define IR_CONTROL_OFFSET       0x02
-%define FCR_OFFSET              0x02
-%define EIR_OFFSET              0x02
-%define BSR_OFFSET              0x03
-%define LCR_OFFSET              0x03
-%define MCR_OFFSET              0x04
-%define LSR_OFFSET              0x05
-%define MSR_OFFSET              0x06
-
-;//---------------------------------------------
-;// UART Register Bit Defines
-;//---------------------------------------------
-%define LSR_TXRDY               0x20
-%define LSR_RXDA                0x01
-%define DLAB                    0x01
-
-; UINT16  gComBase = 0x3f8;
-; UINTN   gBps = 115200;
-; UINT8   gData = 8;
-; UINT8   gStop = 1;
-; UINT8   gParity = 0;
-; UINT8   gBreakSet = 0;
-
-%define DEFAULT_COM_BASE 0x3f8
-%define DEFAULT_BPS 115200
-%define DEFAULT_DATA 8
-%define DEFAULT_STOP 1
-%define DEFAULT_PARITY 0
-%define DEFAULT_BREAK_SET 0
-
-%define SERIAL_DEFAULT_LCR ( \
-     (DEFAULT_BREAK_SET << 6) | \
-     (DEFAULT_PARITY << 3) | \
-     (DEFAULT_STOP << 2) | \
-     (DEFAULT_DATA - 5) \
-    )
-
-%define SERIAL_PORT_IO_BASE_ADDRESS DEFAULT_COM_BASE
-
-%macro  inFromSerialPort 1
-    mov     dx, (SERIAL_PORT_IO_BASE_ADDRESS + %1)
-    in      al, dx
-%endmacro
-
-%macro  waitForSerialTxReady 0
-
-%%waitingForTx:
-    inFromSerialPort LSR_OFFSET
-    test    al, LSR_TXRDY
-    jz      %%waitingForTx
-
-%endmacro
-
-%macro  outToSerialPort 2
-    mov     dx, (SERIAL_PORT_IO_BASE_ADDRESS + %1)
-    mov     al, %2
-    out     dx, al
-%endmacro
-
-%macro  debugShowCharacter 1
-    waitForSerialTxReady
-    outToSerialPort 0, %1
-%endmacro
-
-%macro  debugShowHexDigit 1
-  %if (%1 < 0xa)
-    debugShowCharacter BYTE ('0' + (%1))
-  %else
-    debugShowCharacter BYTE ('a' + ((%1) - 0xa))
-  %endif
-%endmacro
-
-%macro  debugNewline 0
-    debugShowCharacter `\r`
-    debugShowCharacter `\n`
-%endmacro
-
-%macro  debugShowPostCode 1
-    debugShowHexDigit (((%1) >> 4) & 0xf)
-    debugShowHexDigit ((%1) & 0xf)
-    debugNewline
-%endmacro
-
-BITS    16
-
-%macro  debugInitialize 0
-	jmp	real16InitDebug
-real16InitDebugReturn:
-%endmacro
-
-real16InitDebug:
-    ;
-    ; Set communications format
-    ;
-    outToSerialPort LCR_OFFSET, ((DLAB << 7) | SERIAL_DEFAULT_LCR)
-
-    ;
-    ; Configure baud rate
-    ;
-    outToSerialPort BAUD_HIGH_OFFSET, ((115200 / DEFAULT_BPS) >> 8)
-    outToSerialPort BAUD_LOW_OFFSET, ((115200 / DEFAULT_BPS) & 0xff)
-
-    ;
-    ; Switch back to bank 0
-    ;
-    outToSerialPort LCR_OFFSET, SERIAL_DEFAULT_LCR
-
-    jmp     real16InitDebugReturn
-