1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
|
###############################################################################
# Application options
APPL_TRACE_LEVEL=0xFF
PROTOCOL_TRACE_LEVEL=0xFFFFFFFF
###############################################################################
# performance measurement
# Change this setting to control how often USERIAL log the performance (throughput)
# data on read/write/poll
# defailt is to log performance dara for every 100 read or write
#REPORT_PERFORMANCE_MEASURE=100
###############################################################################
# File used for NFA storage
NFA_STORAGE="/data/nfc"
PRESERVE_STORAGE=1
###############################################################################
# Insert a delay in milliseconds after NFC_WAKE and before write to NFCC
NFC_WAKE_DELAY=20
###############################################################################
# Various Delay settings (in ms) used in USERIAL
# POWER_ON_DELAY
# Delay after turning on chip, before writing to transport (default 300)
# PRE_POWER_OFF_DELAY
# Delay after deasserting NFC-Wake before turn off chip (default 0)
# POST_POWER_OFF_DELAY
# Delay after turning off chip, before USERIAL_close returns (default 0)
#
POWER_ON_DELAY=50
PRE_POWER_OFF_DELAY=10
#POST_POWER_OFF_DELAY=0
###############################################################################
# Maximum time (ms) to wait for RESET NTF after setting REG_PU to high
# The default is 1000.
NFCC_ENABLE_TIMEOUT=0
###############################################################################
# Device Manager Config
#
# If NFA_DM_CFG is not provided, stack default settings are
# used (see nfa_dm_cfg.c). They are as follows:
# 0 (FALSE) Automatic NDEF detection when background polling
# 0 (FALSE) Automatic NDEF read when background polling
#
#NFA_DM_CFG={00:00}
###############################################################################
# Default poll duration (in ms)
# The defualt is 500ms if not set (see nfc_target.h)
#NFA_DM_DISC_DURATION_POLL=500
###############################################################################
# Startup Vendor Specific Configuration (100 bytes maximum);
# byte[0] TLV total len = 0x5
# byte[1] NCI_MTS_CMD|NCI_GID_PROP = 0x2f
# byte[2] NCI_MSG_FRAME_LOG = 0x9
# byte[3] 2
# byte[4] 0=turn off RF frame logging; 1=turn on
# byte[5] 0=turn off SWP frame logging; 1=turn on
# NFA_DM_START_UP_VSC_CFG={05:2F:09:02:01:01}
###############################################################################
# Configure the default Destination Gate used by HCI (the default is 4, which
# is the ETSI loopback gate.
#NFA_HCI_DEFAULT_DEST_GATE=0x04
###############################################################################
# Override the stack default for NFA_EE_MAX_EE_SUPPORTED set in nfc_target.h.
# The value is set to 3 by default as it assumes we will discover 0xF2,
# 0xF3, and 0xF4. If a platform will exclude an SE, this value can be reduced
# so that the stack will not wait any longer than necessary. It can be set to
# 0 to disable EE and HCI sub-systems (i.e. if there are no SE on the system).
# Note, if set to 0, the ACTIVE_SE setting should also be set to 0.
#NFA_MAX_EE_SUPPORTED=0
###############################################################################
# Configure the single default SE to use. The default is to use the first
# SE that is detected by the stack. This value might be used when the phone
# supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use
# one of them (e.g. 0xF4). This can be set to 0 if there are no SE on the
# system in order to skip SE initialization.
ACTIVE_SE=0xF3
###############################################################################
# Configure the default NfcA/IsoDep techology and protocol route. Can be
# either a secure element (e.g. 0xF4) or the host (0x00)
DEFAULT_ISODEP_ROUTE=0x00
###############################################################################
# Configure the default "off-host" AID route. The default is 0xF4
DEFAULT_OFFHOST_ROUTE=0xF3
###############################################################################
# Configure the NFC Extras to open and use a static pipe. If the value is
# not set or set to 0, then the default is use a dynamic pipe based on a
# destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value
# for each UICC (where F3="UICC0" and F4="UICC1")
#NFA_HCI_STATIC_PIPE_ID_F3=0x70
#NFA_HCI_STATIC_PIPE_ID_F4=0x71
###############################################################################
# When disconnecting from Oberthur secure element, perform a warm-reset of
# the secure element to deselect the applet.
# The default hex value of the command is 0x3. If this variable is undefined,
# then this feature is not used.
OBERTHUR_WARM_RESET_COMMAND=0x03
###############################################################################
# Force UICC to only listen to the following technology(s).
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B.
#UICC_LISTEN_TECH_MASK=0x01
###############################################################################
# AID for Empty Select command
# If specified, this AID will be substituted when an Empty SELECT command is
# detected. The first byte is the length of the AID. Maximum length is 16.
AID_FOR_EMPTY_SELECT={08:A0:00:00:01:51:00:00:00}
###############################################################################
# Force tag polling for the following technology(s).
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B |
# NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ISO15693 |
# NFA_TECHNOLOGY_MASK_B_PRIME | NFA_TECHNOLOGY_MASK_A_ACTIVE |
# NFA_TECHNOLOGY_MASK_F_ACTIVE.
#
# Notable bits:
# NFA_TECHNOLOGY_MASK_A 0x01
# NFA_TECHNOLOGY_MASK_B 0x02
# NFA_TECHNOLOGY_MASK_F 0x04
# NFA_TECHNOLOGY_MASK_ISO15693 0x08
# NFA_TECHNOLOGY_MASK_B_PRIME 0x10
# NFA_TECHNOLOGY_MASK_KOVIO 0x20
# NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40
# NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80
POLLING_TECH_MASK=0xEF
###############################################################################
# Force P2P to only listen for the following technology(s).
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_F |
# NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE
#P2P_LISTEN_TECH_MASK=0xC5
###############################################################################
# Maximum Number of Credits to be allowed by the NFCC
# This value overrides what the NFCC specifices allowing the host to have
# the control to work-around transport limitations. If this value does
# not exist or is set to 0, the NFCC will provide the number of credits.
#MAX_RF_DATA_CREDITS=1
###############################################################################
# When screen is turned off, specify the desired power state of the controller.
# 0: power-off-sleep state; DEFAULT
# 1: full-power state
# 2: screen-off card-emulation (CE4/CE3/CE1 modes are used)
SCREEN_OFF_POWER_STATE=1
###############################################################################
# SPD Debug mode
# If set to 1, any failure of downloading a patch will trigger a hard-stop
#SPD_DEBUG=0
###############################################################################
# SPD Max Retry Count
# The number of attempts to download a patch before giving up (defualt is 3).
# Note, this resets after a power-cycle.
#SPD_MAX_RETRY_COUNT=3
###############################################################################
# transport driver
#
# TRANSPORT_DRIVER=<driver>
#
# where <driver> can be, for example:
# "/dev/ttyS" (UART)
# "/dev/bcmi2cnfc" (I2C)
# "hwtun" (HW Tunnel)
# "/dev/bcmspinfc" (SPI)
# "/dev/btusb0" (BT USB)
TRANSPORT_DRIVER="/dev/bcm2079x-i2c"
###############################################################################
# power control driver
# Specify a kernel driver that support ioctl commands to control NFC_EN and
# NFC_WAKE gpio signals.
#
# POWER_CONTRL_DRIVER=<driver>
# where <driver> can be, for example:
# "/dev/nfcpower"
# "/dev/bcmi2cnfc" (I2C)
# "/dev/bcmspinfc" (SPI)
# i2c and spi driver may be used to control NFC_EN and NFC_WAKE signal
POWER_CONTROL_DRIVER="/dev/bcm2079x-i2c"
###############################################################################
# I2C transport driver options
# BCMI2CNFC_ADDRESS=0
###############################################################################
# I2C transport driver try to read multiple packets in read() if data is available
# remove the comment below to enable this feature
#READ_MULTIPLE_PACKETS=1
###############################################################################
# SPI transport driver options
#SPI_NEGOTIATION={0A:F0:00:01:00:00:00:FF:FF:00:00}
###############################################################################
# UART transport driver options
#
# PORT=1,2,3,...
# BAUD=115200, 19200, 9600, 4800,
# DATABITS=8, 7, 6, 5
# PARITY="even" | "odd" | "none"
# STOPBITS="0" | "1" | "1.5" | "2"
#UART_PORT=2
#UART_BAUD=115200
#UART_DATABITS=8
#UART_PARITY="none"
#UART_STOPBITS="1"
###############################################################################
# Insert a delay in microseconds per byte after a write to NFCC.
# after writing a block of data to the NFCC, delay this an amopunt of time before
# writing next block of data. the delay is calculated as below
# NFC_WRITE_DELAY * (number of byte written) / 1000 milliseconds
# e.g. after 259 bytes is written, delay (259 * 20 / 1000) 5 ms before next write
NFC_WRITE_DELAY=20
###############################################################################
# Configuration for the RF discovery frequency for each technology. The values mean
# frequency for NFC Technology A
# Technology B
# Technology F
# Proprietary Technology/15693
# Proprietary Technology/B-Prime
# Proprietary Technology/Kovio
# Technology A active mode
# Technology F active mode
#POLL_FREQUENCY={01:01:01:01:01:01:01:01}
###############################################################################
# Define the following variables to override the NFC stack's crystal
# frequency selection algorithm.
#XTAL_HARDWARE_ID=0x20791000: Controller's hardware ID.
#XTAL_FREQUENCY=26000: Controller's crystal frequency.
#XTAL_FREQ_INDEX=5: Controller's crystal frequency index.
###############################################################################
# Choose the presence-check algorithm for type-4 tag. If not defined,
# the default value is 1.
# 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm
# 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block
# 2 NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate
# 3 NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0
# 4 NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3
PRESENCE_CHECK_ALGORITHM=1
|
