/* * Custom OID/ioctl definitions for * Broadcom 802.11abg Networking Device Driver * * Definitions subject to change without notice. * * Copyright (C) 2022, Broadcom. * * Unless you and Broadcom execute a separate written software license * agreement governing use of this software, this software is licensed to you * under the terms of the GNU General Public License version 2 (the "GPL"), * available at http://www.broadcom.com/licenses/GPLv2.php, with the * following added to such license: * * As a special exception, the copyright holders of this software give you * permission to link this software with independent modules, and to copy and * distribute the resulting executable under terms of your choice, provided that * you also meet, for each linked independent module, the terms and conditions of * the license of that module. An independent module is a module which is not * derived from this software. The special exception does not apply to any * modifications of the software. * * * <> */ #ifndef wlioctl_defs_h #define wlioctl_defs_h #ifdef EFI /* * This is the Broadcom-specific guid selector for IOCTL handler in the 80211 Protocol * define for EFI. However, we use last 4 nibbles to communicate 'cmd' from tool to * driver. */ #define BCMWL_IOCTL_GUID \ {0xB4910A35, 0x88C5, 0x4328, { 0x90, 0x08, 0x9F, 0xB2, 0x00, 0x00, 0x0, 0x0 } } #endif /* EFI */ /* All builds use the new 11ac ratespec/chanspec */ #undef D11AC_IOTYPES #define D11AC_IOTYPES #ifdef USE_LEGACY_RSPEC_DEFS typedef uint32 ratespec_t; /* Remove when no referencing branches exist. * These macros will be used only in older branches (prior to K branch). * Wl layer in newer branches and trunk use those defined in bcmwifi_rspec.h. * Non-wl layer in newer branches and trunk may use these as well * until they are removed. */ /* WL_RSPEC defines for rate information */ #define WL_RSPEC_RATE_MASK 0x000000FF /* rate or HT MCS value */ #define WL_RSPEC_VHT_MCS_MASK 0x0000000F /* VHT MCS value */ #define WL_RSPEC_VHT_NSS_MASK 0x000000F0 /* VHT Nss value */ #define WL_RSPEC_VHT_NSS_SHIFT 4 /* VHT Nss value shift */ #define WL_RSPEC_TXEXP_MASK 0x00000300 #define WL_RSPEC_TXEXP_SHIFT 8 #define WL_RSPEC_BW_MASK 0x00070000 /* bandwidth mask */ #define WL_RSPEC_BW_SHIFT 16 /* bandwidth shift */ #define WL_RSPEC_STBC 0x00100000 /* STBC encoding, Nsts = 2 x Nss */ #define WL_RSPEC_TXBF 0x00200000 /* bit indicates TXBF mode */ #define WL_RSPEC_LDPC 0x00400000 /* bit indicates adv coding in use */ #define WL_RSPEC_SGI 0x00800000 /* Short GI mode */ #define WL_RSPEC_ENCODING_MASK 0x03000000 /* Encoding of Rate/MCS field */ #define WL_RSPEC_OVERRIDE_RATE 0x40000000 /* bit indicate to override mcs only */ #define WL_RSPEC_OVERRIDE_MODE 0x80000000 /* bit indicates override rate & mode */ /* WL_RSPEC_ENCODING field defs */ #define WL_RSPEC_ENCODE_RATE 0x00000000 /* Legacy rate is stored in RSPEC_RATE_MASK */ #define WL_RSPEC_ENCODE_HT 0x01000000 /* HT MCS is stored in RSPEC_RATE_MASK */ #define WL_RSPEC_ENCODE_VHT 0x02000000 /* VHT MCS and Nss is stored in RSPEC_RATE_MASK */ /* WL_RSPEC_BW field defs */ #define WL_RSPEC_BW_UNSPECIFIED 0 #define WL_RSPEC_BW_20MHZ 0x00010000 #define WL_RSPEC_BW_40MHZ 0x00020000 #define WL_RSPEC_BW_80MHZ 0x00030000 #define WL_RSPEC_BW_160MHZ 0x00040000 #define WL_RSPEC_BW_10MHZ 0x00050000 #define WL_RSPEC_BW_5MHZ 0x00060000 #define WL_RSPEC_BW_2P5MHZ 0x00070000 #define HIGHEST_SINGLE_STREAM_MCS 7 /* MCS values greater than this enable multiple streams */ #endif /* USE_LEGACY_RSPEC_DEFS */ /* Legacy defines for the nrate iovar */ #define OLD_NRATE_MCS_INUSE 0x00000080 /* MSC in use,indicates b0-6 holds an mcs */ #define OLD_NRATE_RATE_MASK 0x0000007f /* rate/mcs value */ #define OLD_NRATE_STF_MASK 0x0000ff00 /* stf mode mask: siso, cdd, stbc, sdm */ #define OLD_NRATE_STF_SHIFT 8 /* stf mode shift */ #define OLD_NRATE_OVERRIDE 0x80000000 /* bit indicates override both rate & mode */ #define OLD_NRATE_OVERRIDE_MCS_ONLY 0x40000000 /* bit indicate to override mcs only */ #define OLD_NRATE_SGI 0x00800000 /* sgi mode */ #define OLD_NRATE_LDPC_CODING 0x00400000 /* bit indicates adv coding in use */ #define OLD_NRATE_STF_SISO 0 /* stf mode SISO */ #define OLD_NRATE_STF_CDD 1 /* stf mode CDD */ #define OLD_NRATE_STF_STBC 2 /* stf mode STBC */ #define OLD_NRATE_STF_SDM 3 /* stf mode SDM */ #define WLC_11N_N_PROP_MCS 6 /* number of proprietary 11n MCS'es */ #define WLC_11N_FIRST_PROP_MCS 87 /* first Broadcom proprietary MCS */ #define WLC_11N_LAST_PROP_MCS 102 #define MAX_CCA_CHANNELS 38 /* Max number of 20 Mhz wide channels */ #define MAX_CCA_SECS 1 /* CCA keeps this many seconds history - trimmed for dongle */ #define IBSS_MED 15 /* Mediom in-bss congestion percentage */ #define IBSS_HI 25 /* Hi in-bss congestion percentage */ #define OBSS_MED 12 #define OBSS_HI 25 #define INTERFER_MED 5 #define INTERFER_HI 10 #define CCA_FLAG_2G_ONLY 0x01 /* Return a channel from 2.4 Ghz band */ #define CCA_FLAG_5G_ONLY 0x02 /* Return a channel from 2.4 Ghz band */ #define CCA_FLAG_IGNORE_DURATION 0x04 /* Ignore dwell time for each channel */ #define CCA_FLAGS_PREFER_1_6_11 0x10 #define CCA_FLAG_IGNORE_INTERFER 0x20 /* do not exclude channel based on interfer level */ #define CCA_ERRNO_BAND 1 /* After filtering for band pref, no choices left */ #define CCA_ERRNO_DURATION 2 /* After filtering for duration, no choices left */ #define CCA_ERRNO_PREF_CHAN 3 /* After filtering for chan pref, no choices left */ #define CCA_ERRNO_INTERFER 4 /* After filtering for interference, no choices left */ #define CCA_ERRNO_TOO_FEW 5 /* Only 1 channel was input */ #define WL_STA_AID(a) ((a) &~ 0xc000) /* Flags for sta_info_t indicating properties of STA */ #define WL_STA_BRCM 0x00000001 /* Running a Broadcom driver */ #define WL_STA_WME 0x00000002 /* WMM association */ #define WL_STA_NONERP 0x00000004 /* No ERP */ #define WL_STA_AUTHE 0x00000008 /* Authenticated */ #define WL_STA_ASSOC 0x00000010 /* Associated */ #define WL_STA_AUTHO 0x00000020 /* Authorized */ #define WL_STA_WDS 0x00000040 /* Wireless Distribution System */ #define WL_STA_WDS_LINKUP 0x00000080 /* WDS traffic/probes flowing properly */ #define WL_STA_PS 0x00000100 /* STA is in power save mode from AP's viewpoint */ #define WL_STA_APSD_BE 0x00000200 /* APSD delv/trigger for AC_BE is default enabled */ #define WL_STA_APSD_BK 0x00000400 /* APSD delv/trigger for AC_BK is default enabled */ #define WL_STA_APSD_VI 0x00000800 /* APSD delv/trigger for AC_VI is default enabled */ #define WL_STA_APSD_VO 0x00001000 /* APSD delv/trigger for AC_VO is default enabled */ #define WL_STA_N_CAP 0x00002000 /* STA 802.11n capable */ #define WL_STA_SCBSTATS 0x00004000 /* Per STA debug stats */ #define WL_STA_AMPDU_CAP 0x00008000 /* STA AMPDU capable */ #define WL_STA_AMSDU_CAP 0x00010000 /* STA AMSDU capable */ #define WL_STA_MIMO_PS 0x00020000 /* mimo ps mode is enabled */ #define WL_STA_MIMO_RTS 0x00040000 /* send rts in mimo ps mode */ #define WL_STA_RIFS_CAP 0x00080000 /* rifs enabled */ #define WL_STA_VHT_CAP 0x00100000 /* STA VHT(11ac) capable */ #define WL_STA_WPS 0x00200000 /* WPS state */ #define WL_STA_DWDS_CAP 0x01000000 /* DWDS CAP */ #define WL_STA_DWDS 0x02000000 /* DWDS active */ #define WL_WDS_LINKUP WL_STA_WDS_LINKUP /* deprecated */ #define WL_STA_IS_2G 0x04000000 /* 2G channels supported */ #define WL_STA_IS_5G 0x08000000 /* 5G channels supported */ #define WL_STA_IS_6G 0x10000000 /* 6G channels supported */ /* STA HT cap fields */ #define WL_STA_CAP_LDPC_CODING 0x0001 /* Support for rx of LDPC coded pkts */ #define WL_STA_CAP_40MHZ 0x0002 /* FALSE:20Mhz, TRUE:20/40MHZ supported */ #define WL_STA_CAP_MIMO_PS_MASK 0x000C /* Mimo PS mask */ #define WL_STA_CAP_MIMO_PS_SHIFT 0x0002 /* Mimo PS shift */ #define WL_STA_CAP_MIMO_PS_OFF 0x0003 /* Mimo PS, no restriction */ #define WL_STA_CAP_MIMO_PS_RTS 0x0001 /* Mimo PS, send RTS/CTS around MIMO frames */ #define WL_STA_CAP_MIMO_PS_ON 0x0000 /* Mimo PS, MIMO disallowed */ #define WL_STA_CAP_GF 0x0010 /* Greenfield preamble support */ #define WL_STA_CAP_SHORT_GI_20 0x0020 /* 20MHZ short guard interval support */ #define WL_STA_CAP_SHORT_GI_40 0x0040 /* 40Mhz short guard interval support */ #define WL_STA_CAP_TX_STBC 0x0080 /* Tx STBC support */ #define WL_STA_CAP_RX_STBC_MASK 0x0300 /* Rx STBC mask */ #define WL_STA_CAP_RX_STBC_SHIFT 8 /* Rx STBC shift */ #define WL_STA_CAP_DELAYED_BA 0x0400 /* delayed BA support */ #define WL_STA_CAP_MAX_AMSDU 0x0800 /* Max AMSDU size in bytes , 0=3839, 1=7935 */ #define WL_STA_CAP_DSSS_CCK 0x1000 /* DSSS/CCK supported by the BSS */ #define WL_STA_CAP_PSMP 0x2000 /* Power Save Multi Poll support */ #define WL_STA_CAP_40MHZ_INTOLERANT 0x4000 /* 40MHz Intolerant */ #define WL_STA_CAP_LSIG_TXOP 0x8000 /* L-SIG TXOP protection support */ #define WL_STA_CAP_RX_STBC_NO 0x0 /* no rx STBC support */ #define WL_STA_CAP_RX_STBC_ONE_STREAM 0x1 /* rx STBC support of 1 spatial stream */ #define WL_STA_CAP_RX_STBC_TWO_STREAM 0x2 /* rx STBC support of 1-2 spatial streams */ #define WL_STA_CAP_RX_STBC_THREE_STREAM 0x3 /* rx STBC support of 1-3 spatial streams */ /* scb vht flags */ #define WL_STA_VHT_LDPCCAP 0x0001 #define WL_STA_SGI80 0x0002 #define WL_STA_SGI160 0x0004 #define WL_STA_VHT_TX_STBCCAP 0x0008 #define WL_STA_VHT_RX_STBCCAP 0x0010 #define WL_STA_SU_BEAMFORMER 0x0020 #define WL_STA_SU_BEAMFORMEE 0x0040 #define WL_STA_MU_BEAMFORMER 0x0080 #define WL_STA_MU_BEAMFORMEE 0x0100 #define WL_STA_VHT_TXOP_PS 0x0200 #define WL_STA_HTC_VHT_CAP 0x0400 /* Values for TX Filter override mode */ #define WLC_TXFILTER_OVERRIDE_DISABLED 0 #define WLC_TXFILTER_OVERRIDE_ENABLED 1 #define WL_IOCTL_ACTION_GET 0x0 #define WL_IOCTL_ACTION_SET 0x1 #define WL_IOCTL_ACTION_OVL_IDX_MASK 0x1e #define WL_IOCTL_ACTION_OVL_RSV 0x20 #define WL_IOCTL_ACTION_OVL 0x40 #define WL_IOCTL_ACTION_MASK 0x7e #define WL_IOCTL_ACTION_OVL_SHIFT 1 /* For WLC_SET_INFRA ioctl & infra_configuration iovar SET/GET operations */ #define WL_BSSTYPE_INDEP 0 #define WL_BSSTYPE_INFRA 1 #define WL_BSSTYPE_ANY 2 /* deprecated */ #define WL_BSSTYPE_MESH 3 /* Bit definitions of mws_active_scan_throttle iovar */ #define WL_SCAN_THROTTLE_MASK 0xF #define WL_SCAN_THROTTLE_ASSOCSCAN (1U << 0) #define WL_SCAN_THROTTLE_ROAMSCAN (1U << 1) #define WL_SCAN_THROTTLE_OTHER_FW_SCAN (1U << 2) /* for other scans like pno etc */ #define WL_SCAN_THROTTLE_HOSTSCAN (1U << 3) /* Mask bit for LOW power scan, High accuracy scan, LOW span scan bit defines */ #define WL_SCANFLAGS_SCAN_MODE_MASK 0x7000u #define WL_SCANFLAGS_SCAN_MODE_SHIFT 12u /* Bitmask for scan_type */ /* Reserved flag precludes the use of 0xff for scan_type which is * interpreted as default for backward compatibility. * Low priority scan uses currently reserved bit, * this should be changed as scan_type extended. * So, reserved flag definition removed. */ /* Use lower 16 bit for scan flags, the upper 16 bits are for internal use */ #define WL_SCANFLAGS_PASSIVE 0x01U /* force passive scan */ #define WL_SCANFLAGS_LOW_PRIO 0x02U /* Low priority scan */ #define WL_SCANFLAGS_PROHIBITED 0x04U /* allow scanning prohibited channels */ #define WL_SCANFLAGS_OFFCHAN 0x08U /* allow scanning/reporting off-channel * APs. */ #define WL_SCANFLAGS_HOTSPOT 0x10U /* automatic ANQP to hotspot APs */ #define WL_SCANFLAGS_SWTCHAN 0x20U /* Force channel switch for differerent * bandwidth. */ #define WL_SCANFLAGS_FORCE_PARALLEL 0x40U /* Force parallel scan even when actcb_fn_t * is on.By default parallel scan will be * disabled if actcb_fn_t is provided. */ #define WL_SCANFLAGS_SISO 0x40U /* Use 1 RX chain for scanning */ #define WL_SCANFLAGS_MIMO 0x80U /* Force MIMO scanning */ #define WL_SCANFLAGS_NO_6GHZ_FOLLOWUP 0x100U /* No 6G active scan due to RNR or FILS */ #define WL_SCANFLAGS_INCL_FILS_DISC_FRAMES 0x200U /* Include Fils info as well in * escan results. */ #define WL_SCANFLAGS_FORCE_SCAN_CORE_6G_SCAN 0x400U /* Force 6G scan on Scan core. */ #define WL_SCANFLAGS_INCL_ORIG_RNR 0x800U /* Include scan results with * matching RNR BSS */ /* This is to re purpose the definition to firmware internal use. * By repurposing these bit values can be used for host. * These are moved to higher bits and defined in firmware. */ #ifndef WL_SCANFLAGS_INT_SCANTYPE_HAS_ALIAS /* Mask bit for Assoc scan, Roam scan, Other FW scan, Host scan bit defines */ #define WL_SCANFLAGS_CLIENT_MASK 0xF00u #define WL_SCANFLAGS_CLIENT_SHIFT 8 #define WL_SCANFLAGS_ASSOCSCAN 0x100U /* Assoc scan */ #define WL_SCANFLAGS_ROAMSCAN 0x200U /* Roam scan */ #define WL_SCANFLAGS_FWSCAN 0x400U /* Other FW scan */ #define WL_SCANFLAGS_HOSTSCAN 0x800U /* Host scan */ #endif /* WL_SCANFLAGS_INT_SCANTYPE_HAS_ALIAS */ #define WL_SCANFLAGS_LOW_POWER_SCAN 0x1000U /* LOW power scan, scheduled scan * only on scancore */ #define WL_SCANFLAGS_HIGH_ACCURACY 0x2000U /* High accuracy scan, which needs * reliable scan results */ #define WL_SCANFLAGS_LOW_SPAN 0x4000U /* LOW span scan, which expects * scan to be completed ASAP */ #define WL_SCANFLAGS_LISTEN 0x8000U /* Listen option in escan * enable LISTEN along with PASSIVE flag */ /* BIT MASK for 6G_SCAN_TYPE */ #define WL_SCAN_SSIDFLAGS_SHORT_SSID 0x01U /* include short ssid */ #define WL_SCAN_INC_RNR 0x02U /* Include RNR channels for scan */ #define WL_SCAN_SKIP_FILS_DISCOVERY_PERIOD 0x04U /* Skip FILS Discovery Period for 6G chans */ #define WL_SCAN_ACTIVE_6GHZ 0x08U /* Force active scan for 6GHZ channel */ /* Value to decide scan type based on scqs */ #define WL_SC_RETRY_SCAN_MODE_NO_SCAN 0x0u /* Do not reschedule scan */ #define WL_SC_RETRY_SCAN_MODE_HIGH_ACC 0x1u /* Reschedule scan as HighAccuracy */ #define WL_SC_RETRY_SCAN_MODE_LOWPOWER 0x2u /* Reschedule scan as LOWPOWER */ #define WL_SC_RETRY_SCAN_MODE_AUTO 0x3u /* Scan rescheduling type is decided * dynamically. */ /* wl_iscan_results status values */ #define WL_SCAN_RESULTS_SUCCESS 0 #define WL_SCAN_RESULTS_PARTIAL 1 #define WL_SCAN_RESULTS_PENDING 2 #define WL_SCAN_RESULTS_ABORTED 3 #define WL_SCAN_RESULTS_NO_MEM 4 /* Flags for parallel scan */ /* Bitmap to enable/disable rsdb parallel scan, 5g-5g/2g-2g parallel scan * SCAN_PARALLEL_PASSIVE_5G ==> 5g-5g parallel scan * SCAN_PARALLEL_PASSIVE_2G ==> 2g-2g parallel scan */ #define SCAN_PARALLEL_PASSIVE_5G (0x40) #define SCAN_PARALLEL_PASSIVE_2G (0x80) #define SCANOL_ENABLED (1 << 0) #define SCANOL_BCAST_SSID (1 << 1) #define SCANOL_NOTIFY_BCAST_SSID (1 << 2) #define SCANOL_RESULTS_PER_CYCLE (1 << 3) /* scan times in milliseconds */ #define SCANOL_HOME_TIME 45 /* for home channel processing */ #define SCANOL_ASSOC_TIME 20 /* dwell on a channel while associated */ #define SCANOL_UNASSOC_TIME 40 /* dwell on a channel while unassociated */ #define SCANOL_PASSIVE_TIME 110 /* listen on a channelfor passive scan */ #define SCANOL_AWAY_LIMIT 100 /* max time to be away from home channel */ #define SCANOL_IDLE_REST_TIME 40 #define SCANOL_IDLE_REST_MULTIPLIER 0 #define SCANOL_ACTIVE_REST_TIME 20 #define SCANOL_ACTIVE_REST_MULTIPLIER 0 #define SCANOL_CYCLE_IDLE_REST_TIME 300000 /* Idle Rest Time between Scan Cycle (msec) */ #define SCANOL_CYCLE_IDLE_REST_MULTIPLIER 0 /* Idle Rest Time Multiplier */ #define SCANOL_CYCLE_ACTIVE_REST_TIME 200 #define SCANOL_CYCLE_ACTIVE_REST_MULTIPLIER 0 #define SCANOL_MAX_REST_TIME 3600000 /* max rest time between scan cycle (msec) */ #define SCANOL_CYCLE_DEFAULT 0 /* default for Max Scan Cycle, 0 = forever */ #define SCANOL_CYCLE_MAX 864000 /* Max Scan Cycle */ /* 10 sec/scan cycle => 100 days */ #define SCANOL_NPROBES 2 /* for Active scan; send n probes on each channel */ #define SCANOL_NPROBES_MAX 5 /* for Active scan; send n probes on each channel */ #define SCANOL_SCAN_START_DLY 10 /* delay start of offload scan (sec) */ #define SCANOL_SCAN_START_DLY_MAX 240 /* delay start of offload scan (sec) */ #define SCANOL_MULTIPLIER_MAX 10 /* Max Multiplier */ #define SCANOL_UNASSOC_TIME_MAX 100 /* max dwell on a channel while unassociated */ #define SCANOL_PASSIVE_TIME_MAX 500 /* max listen on a channel for passive scan */ #define SCANOL_SSID_MAX 16 /* max supported preferred SSID */ /* masks for channel and ssid count */ #define WL_SCAN_PARAMS_COUNT_MASK 0x0000ffff #define WL_SCAN_PARAMS_NSSID_SHIFT 16 #define WL_SCAN_ACTION_START 1 #define WL_SCAN_ACTION_CONTINUE 2 #define WL_SCAN_ACTION_ABORT 3 #if defined(SIMPLE_ISCAN) #define ISCAN_RETRY_CNT 5 #define ISCAN_STATE_IDLE 0 #define ISCAN_STATE_SCANING 1 #define ISCAN_STATE_PENDING 2 #endif /* SIMPLE_ISCAN */ #define ANTENNA_NUM_1 1 /* total number of antennas to be used */ #define ANTENNA_NUM_2 2 #define ANTENNA_NUM_3 3 #define ANTENNA_NUM_4 4 #define ANT_SELCFG_AUTO 0x80 /* bit indicates antenna sel AUTO */ #define ANT_SELCFG_MASK 0x33 /* antenna configuration mask */ #define ANT_SELCFG_TX_UNICAST 0 /* unicast tx antenna configuration */ #define ANT_SELCFG_RX_UNICAST 1 /* unicast rx antenna configuration */ #define ANT_SELCFG_TX_DEF 2 /* default tx antenna configuration */ #define ANT_SELCFG_RX_DEF 3 /* default rx antenna configuration */ /* interference source detection and identification mode */ #define ITFR_MODE_DISABLE 0 /* disable feature */ #define ITFR_MODE_MANUAL_ENABLE 1 /* enable manual detection */ #define ITFR_MODE_AUTO_ENABLE 2 /* enable auto detection */ /* bit definitions for flags in interference source report */ #define ITFR_INTERFERENCED 1 /* interference detected */ #define ITFR_HOME_CHANNEL 2 /* home channel has interference */ #define ITFR_NOISY_ENVIRONMENT 4 /* noisy environemnt so feature stopped */ #define WL_NUM_RPI_BINS 8 #define WL_RM_TYPE_BASIC 1 #define WL_RM_TYPE_CCA 2 #define WL_RM_TYPE_RPI 3 #define WL_RM_TYPE_ABORT -1 /* ABORT any in-progress RM request */ #define WL_RM_FLAG_PARALLEL (1<<0) #define WL_RM_FLAG_LATE (1<<1) #define WL_RM_FLAG_INCAPABLE (1<<2) #define WL_RM_FLAG_REFUSED (1<<3) /* flags */ #define WLC_ASSOC_REQ_IS_REASSOC 0x01 /* assoc req was actually a reassoc */ #define WLC_CIS_DEFAULT 0 /* built-in default */ #define WLC_CIS_SROM 1 /* source is sprom */ #define WLC_CIS_OTP 2 /* source is otp */ /* PCL - Power Control Loop */ /* current gain setting is replaced by user input */ #define WL_ATTEN_APP_INPUT_PCL_OFF 0 /* turn off PCL, apply supplied input */ #define WL_ATTEN_PCL_ON 1 /* turn on PCL */ /* current gain setting is maintained */ #define WL_ATTEN_PCL_OFF 2 /* turn off PCL. */ /* defines used by poweridx iovar - it controls power in a-band */ /* current gain setting is maintained */ #define WL_PWRIDX_PCL_OFF -2 /* turn off PCL. */ #define WL_PWRIDX_PCL_ON -1 /* turn on PCL */ #define WL_PWRIDX_LOWER_LIMIT -2 /* lower limit */ #define WL_PWRIDX_UPPER_LIMIT 63 /* upper limit */ /* value >= 0 causes * - input to be set to that value * - PCL to be off */ #define BCM_MAC_STATUS_INDICATION (0x40010200L) /* Values for TX Filter override mode */ #define WLC_TXFILTER_OVERRIDE_DISABLED 0 #define WLC_TXFILTER_OVERRIDE_ENABLED 1 /* magic pattern used for mismatch driver and wl */ #define WL_TXFIFO_SZ_MAGIC 0xa5a5 /* check this magic number */ #define WLC_IOCTL_MAGIC 0x14e46c77 /* bss_info_cap_t flags */ #define WL_BSS_FLAGS_FROM_BEACON 0x01 /* bss_info derived from beacon */ #define WL_BSS_FLAGS_FROM_CACHE 0x02 /* bss_info collected from cache */ #define WL_BSS_FLAGS_RSSI_ONCHANNEL 0x04 /* rssi info received on channel (vs offchannel) */ #define WL_BSS_FLAGS_HS20 0x08 /* hotspot 2.0 capable */ #define WL_BSS_FLAGS_RSSI_INVALID 0x10 /* BSS contains invalid RSSI */ #define WL_BSS_FLAGS_RSSI_INACCURATE 0x20 /* BSS contains inaccurate RSSI */ #define WL_BSS_FLAGS_SNR_INVALID 0x40 /* BSS contains invalid SNR */ #define WL_BSS_FLAGS_NF_INVALID 0x80 /* BSS contains invalid noise floor */ /* bss_info_cap_t flags_2 */ #define WL_BSS_FLAGS_THRU_LPSC 0x01 /* bss_info obtained thru' LPSC */ #define WL_BSS_FLAGS_QBSS_LOAD 0x02 /* QBSS load value present */ #define WL_BSS2_FLAGS_FROM_FILS 0x04 /* values are based on FILS frame */ #define WL_BSS2_FLAGS_SHORT_SSID 0x08 /* values ssid is indicating as short ssid */ #define WL_BSS2_FLAGS_RNR_MATCH 0x10 /* To report original BSS that has RNR match */ #define WL_BSS2_FLAGS_HE_BCN_PRBRSP 0x20u /* BSS update to indiacte HE bcn or prb rsp. */ /* bit definitions for bcnflags in wl_bss_info */ #define WL_BSS_BCNFLAGS_INTERWORK_PRESENT 0x01 /* beacon had IE, accessnet valid */ #define WL_BSS_BCNFLAGS_INTERWORK_PRESENT_VALID 0x02 /* on indicates support for this API */ #define WL_BSS_BCNFLAGS_MULTIPLE_BSSID_SET 0x4 /* this AP belongs to a multiple BSSID set */ #define WL_BSS_BCNFLAGS_NONTRANSMITTED_BSSID 0x8 /* this AP is the transmitted BSSID */ /* bssinfo flag for nbss_cap */ #define VHT_BI_SGI_80MHZ 0x00000100 #define VHT_BI_80MHZ 0x00000200 #define VHT_BI_160MHZ 0x00000400 #define VHT_BI_8080MHZ 0x00000800 /* reference to wl_ioctl_t struct used by usermode driver */ #define ioctl_subtype set /* subtype param */ #define ioctl_pid used /* pid param */ #define ioctl_status needed /* status param */ /* Enumerate crypto algorithms */ #define CRYPTO_ALGO_OFF 0 #define CRYPTO_ALGO_WEP1 1 #define CRYPTO_ALGO_TKIP 2 #define CRYPTO_ALGO_WEP128 3 #define CRYPTO_ALGO_AES_CCM 4 #define CRYPTO_ALGO_AES_OCB_MSDU 5 #define CRYPTO_ALGO_AES_OCB_MPDU 6 #if !defined(BCMCCX) && !defined(BCMEXTCCX) #define CRYPTO_ALGO_NALG 7 #else #define CRYPTO_ALGO_CKIP 7 #define CRYPTO_ALGO_CKIP_MMH 8 #define CRYPTO_ALGO_WEP_MMH 9 #define CRYPTO_ALGO_NALG 10 #endif /* !BCMCCX && !BCMEXTCCX */ #define CRYPTO_ALGO_SMS4 11 #define CRYPTO_ALGO_PMK 12 /* for 802.1x supp to set PMK before 4-way */ #define CRYPTO_ALGO_BIP 13 /* 802.11w BIP (aes cmac) */ #define CRYPTO_ALGO_AES_GCM 14 /* 128 bit GCM */ #define CRYPTO_ALGO_AES_CCM256 15 /* 256 bit CCM */ #define CRYPTO_ALGO_AES_GCM256 16 /* 256 bit GCM */ #define CRYPTO_ALGO_BIP_CMAC256 17 /* 256 bit BIP CMAC */ #define CRYPTO_ALGO_BIP_GMAC 18 /* 128 bit BIP GMAC */ #define CRYPTO_ALGO_BIP_GMAC256 19 /* 256 bit BIP GMAC */ #define CRYPTO_ALGO_NONE CRYPTO_ALGO_OFF /* algo bit vector */ #define KEY_ALGO_MASK(_algo) (1 << _algo) #if defined(BCMCCX) || defined(BCMEXTCCX) #define KEY_ALGO_MASK_CCX (KEY_ALGO_MASK(CRYPTO_ALGO_CKIP) | \ KEY_ALGO_MASK(CRYPTO_ALGO_CKIP_MMH) | \ KEY_ALGO_MASK(CRYPTO_ALGO_WEP_MMH)) #endif /* defined(BCMCCX) || defined(BCMEXTCCX) */ #define KEY_ALGO_MASK_WEP (KEY_ALGO_MASK(CRYPTO_ALGO_WEP1) | \ KEY_ALGO_MASK(CRYPTO_ALGO_WEP128) | \ KEY_ALGO_MASK(CRYPTO_ALGO_NALG)) #define KEY_ALGO_MASK_AES (KEY_ALGO_MASK(CRYPTO_ALGO_AES_CCM) | \ KEY_ALGO_MASK(CRYPTO_ALGO_AES_CCM256) | \ KEY_ALGO_MASK(CRYPTO_ALGO_AES_GCM) | \ KEY_ALGO_MASK(CRYPTO_ALGO_AES_GCM256)) #define KEY_ALGO_MASK_TKIP (KEY_ALGO_MASK(CRYPTO_ALGO_TKIP)) #define KEY_ALGO_MASK_WAPI (KEY_ALGO_MASK(CRYPTO_ALGO_SMS4)) #define WSEC_GEN_MIC_ERROR 0x0001 #define WSEC_GEN_REPLAY 0x0002 #define WSEC_GEN_ICV_ERROR 0x0004 #define WSEC_GEN_MFP_ACT_ERROR 0x0008 #define WSEC_GEN_MFP_DISASSOC_ERROR 0x0010 #define WSEC_GEN_MFP_DEAUTH_ERROR 0x0020 #define WL_SOFT_KEY (1 << 0) /* Indicates this key is using soft encrypt */ #define WL_PRIMARY_KEY (1 << 1) /* Indicates this key is the primary (ie tx) key */ #if defined(BCMCCX) || defined(BCMEXTCCX) #define WL_CKIP_KP (1 << 4) /* CMIC */ #define WL_CKIP_MMH (1 << 5) /* CKIP */ #else #define WL_KF_RES_4 (1 << 4) /* Reserved for backward compat */ #define WL_KF_RES_5 (1 << 5) /* Reserved for backward compat */ #endif /* BCMCCX || BCMEXTCCX */ #define WL_IBSS_PEER_GROUP_KEY (1 << 6) /* Indicates a group key for a IBSS PEER */ #define WL_LINK_KEY (1 << 7) /* For linking keys of both cores */ #define WL_UNLINK_KEY (1 << 8) /* For unlinking keys of both cores */ /* wireless security bitvec */ #define WSEC_NONE 0x0 #define WEP_ENABLED 0x0001 #define TKIP_ENABLED 0x0002 #define AES_ENABLED 0x0004 #define WSEC_SWFLAG 0x0008 #ifdef BCMCCX #define CKIP_KP_ENABLED 0x0010 #define CKIP_MIC_ENABLED 0x0020 #endif /* BCMCCX */ #define SES_OW_ENABLED 0x0040 /* to go into transition mode without setting wep */ #ifdef WLFIPS #define FIPS_ENABLED 0x0080 #endif /* WLFIPS */ #ifdef BCMWAPI_WPI #define SMS4_ENABLED 0x0100 #endif /* BCMWAPI_WPI */ /* wsec macros for operating on the above definitions */ #ifdef WLWSEC #define WSEC_WEP_ENABLED(wsec) ((wsec) & WEP_ENABLED) #define WSEC_TKIP_ENABLED(wsec) ((wsec) & TKIP_ENABLED) #define WSEC_AES_ENABLED(wsec) ((wsec) & AES_ENABLED) #else /* WLWSEC */ #define WSEC_WEP_ENABLED(wsec) NULL #define WSEC_TKIP_ENABLED(wsec) NULL #define WSEC_AES_ENABLED(wsec) NULL #endif /* WLWSEC */ /* Macros to check if algorithm is enabled */ #define WSEC_INFO_ALGO_ENABLED(_wi, _algo) \ (_wi).cur_algos & (1 << CRYPTO_ALGO_##_algo) #define WSEC_INFO_ALGO_NONE(_wi) (((_wi).cur_algos) == 0) #ifdef WLWSEC #ifdef BCMCCX #define WSEC_CKIP_KP_ENABLED(wsec) ((wsec) & CKIP_KP_ENABLED) #define WSEC_CKIP_MIC_ENABLED(wsec) ((wsec) & CKIP_MIC_ENABLED) #define WSEC_CKIP_ENABLED(wsec) ((wsec) & (CKIP_KP_ENABLED|CKIP_MIC_ENABLED)) #ifdef BCMWAPI_WPI #define WSEC_ENABLED(wsec) \ ((wsec) & (WEP_ENABLED | TKIP_ENABLED | AES_ENABLED | CKIP_KP_ENABLED | \ CKIP_MIC_ENABLED | SMS4_ENABLED)) #endif /* BCMWAPI_WPI */ #ifndef BCMWAPI_WPI /* BCMWAPI_WPI */ #define WSEC_ENABLED(wsec) \ ((wsec) & \ (WEP_ENABLED | TKIP_ENABLED | AES_ENABLED | CKIP_KP_ENABLED | CKIP_MIC_ENABLED)) #endif /* BCMWAPI_WPI */ #else /* defined BCMCCX */ #ifdef BCMWAPI_WPI #define WSEC_ENABLED(wsec) ((wsec) & (WEP_ENABLED | TKIP_ENABLED | AES_ENABLED | SMS4_ENABLED)) #endif /* BCMWAPI_WPI */ #ifndef BCMWAPI_WPI /* BCMWAPI_WPI */ #define WSEC_ENABLED(wsec) ((wsec) & (WEP_ENABLED | TKIP_ENABLED | AES_ENABLED)) #endif /* BCMWAPI_WPI */ #endif /* BCMCCX */ #else /* WLWSEC */ #define WSEC_ENABLED(wsec) 0 #endif /* WLWSEC */ #define WSEC_SES_OW_ENABLED(wsec) ((wsec) & SES_OW_ENABLED) #ifdef BCMWAPI_WAI #define WSEC_SMS4_ENABLED(wsec) ((wsec) & SMS4_ENABLED) #endif /* BCMWAPI_WAI */ /* Following macros are not used any more. Just kept here to * avoid build issue in BISON/CARIBOU branch */ #define MFP_CAPABLE 0x0200 #define MFP_REQUIRED 0x0400 #define MFP_SHA256 0x0800 /* a special configuration for STA for WIFI test tool */ /* WPA authentication mode bitvec */ #define WPA_AUTH_DISABLED 0x0000 /* Legacy (i.e., non-WPA) */ #define WPA_AUTH_NONE 0x0001 /* none (IBSS) */ #define WPA_AUTH_UNSPECIFIED 0x0002 /* over 802.1x */ #define WPA_AUTH_PSK 0x0004 /* Pre-shared key */ #if defined(BCMCCX) || defined(BCMEXTCCX) #define WPA_AUTH_CCKM 0x0008 /* CCKM */ #define WPA2_AUTH_CCKM 0x0010 /* CCKM2 */ #endif /* BCMCCX || BCMEXTCCX */ /* #define WPA_AUTH_8021X 0x0020 */ /* 802.1x, reserved */ #define WPA2_AUTH_UNSPECIFIED 0x0040 /* over 802.1x */ #define WPA2_AUTH_PSK 0x0080 /* Pre-shared key */ #define BRCM_AUTH_PSK 0x0100 /* BRCM specific PSK */ #define BRCM_AUTH_DPT 0x0200 /* DPT PSK without group keys */ #if defined(BCMWAPI_WAI) || defined(BCMWAPI_WPI) #define WPA_AUTH_WAPI 0x0400 /* why it is same as WAPI_AUTH_UNSPECIFIED */ #define WAPI_AUTH_NONE WPA_AUTH_NONE /* none (IBSS) */ #define WAPI_AUTH_UNSPECIFIED 0x0400 /* over AS */ #define WAPI_AUTH_PSK 0x0800 /* Pre-shared key */ #endif /* BCMWAPI_WAI || BCMWAPI_WPI */ #define WPA2_AUTH_1X_SHA256 0x1000 /* 1X with SHA256 key derivation */ #define WPA2_AUTH_TPK 0x2000 /* TDLS Peer Key */ #define WPA2_AUTH_FT 0x4000 /* Fast Transition. */ #define WPA2_AUTH_PSK_SHA256 0x8000 /* PSK with SHA256 key derivation */ #define WPA2_AUTH_FILS_SHA256 0x10000 /* FILS with SHA256 key derivation */ #define WPA2_AUTH_FILS_SHA384 0x20000 /* FILS with SHA384 key derivation */ #define WPA2_AUTH_IS_FILS(auth) ((auth) & (WPA2_AUTH_FILS_SHA256 | WPA2_AUTH_FILS_SHA384)) #define WPA3_AUTH_SAE_PSK 0x40000 /* SAE with 4-way handshake */ #define WPA3_AUTH_DPP_AKM 0x80000 /* Device Provisioning Protocol (DPP) */ #define WPA3_AUTH_OWE 0x100000 /* OWE */ #define WPA3_AUTH_1X_SUITE_B_SHA256 0x200000 /* Suite B SHA256 */ #define WPA3_AUTH_1X_SUITE_B_SHA384 0x400000 /* Suite B-192 SHA384 */ #define WPA3_AUTH_PSK_SHA384 0x800000 /* PSK with SHA384 key derivation */ #define WPA3_AUTH_SAE_AP_ONLY 0x1000000 /* SAE restriction to connect to pure SAE APs */ /* WPA2_AUTH_SHA256 not used anymore. Just kept here to avoid build issue in DINGO */ #define WPA2_AUTH_SHA256 0x8000 #define WPA_AUTH_PFN_ANY 0xffffffff /* for PFN, match only ssid */ /* pmkid */ #define MAXPMKID 16 /* max # PMKID cache entries NDIS */ #ifdef MACOSX /* Macos limits ioctl maxlen for TX to 1864 and for RX to 2004 */ #define WLC_IOCTL_MAXLEN 2000 /* "max" length ioctl buffer */ #else #define WLC_IOCTL_MAXLEN 8192u /* "max" length ioctl buffer */ #endif /* MACOSX */ #define WLC_IOCTL_MEDLEN 1936u /* "med" length ioctl buffer */ #define WLC_IOCTL_SMLEN 256u /* "small" length ioctl buffer */ #define WLC_SAMPLECOLLECT_MAXLEN 10240u /* Max Sample Collect buffer for two cores */ #define WLC_IOCTL_NANRESP_MAXLEN 4096u /* "max" length nan ioctl resp buffer */ #define WLC_IOCTL_NANRESP_MEDLEN WLC_IOCTL_MEDLEN /* "med" length nan ioctl resp buffer */ /* common ioctl definitions */ #define WLC_GET_MAGIC 0 #define WLC_GET_VERSION 1 #define WLC_UP 2 #define WLC_DOWN 3 #define WLC_GET_LOOP 4 #define WLC_SET_LOOP 5 #define WLC_DUMP 6 #define WLC_GET_MSGLEVEL 7 #define WLC_SET_MSGLEVEL 8 #define WLC_GET_PROMISC 9 #define WLC_SET_PROMISC 10 /* #define WLC_OVERLAY_IOCTL 11 */ /* not supported */ #define WLC_GET_RATE 12 #define WLC_GET_MAX_RATE 13 #define WLC_GET_INSTANCE 14 /* #define WLC_GET_FRAG 15 */ /* no longer supported */ /* #define WLC_SET_FRAG 16 */ /* no longer supported */ /* #define WLC_GET_RTS 17 */ /* no longer supported */ /* #define WLC_SET_RTS 18 */ /* no longer supported */ #define WLC_GET_INFRA 19 #define WLC_SET_INFRA 20 #define WLC_GET_AUTH 21 #define WLC_SET_AUTH 22 #define WLC_GET_BSSID 23 #define WLC_SET_BSSID 24 #define WLC_GET_SSID 25 #define WLC_SET_SSID 26 #define WLC_RESTART 27 #define WLC_TERMINATED 28 /* #define WLC_DUMP_SCB 28 */ /* no longer supported */ #define WLC_GET_CHANNEL 29 #define WLC_SET_CHANNEL 30 #define WLC_GET_SRL 31 #define WLC_SET_SRL 32 #define WLC_GET_LRL 33 #define WLC_SET_LRL 34 #define WLC_GET_PLCPHDR 35 #define WLC_SET_PLCPHDR 36 #define WLC_GET_RADIO 37 #define WLC_SET_RADIO 38 #define WLC_GET_PHYTYPE 39 #define WLC_DUMP_RATE 40 #define WLC_SET_RATE_PARAMS 41 #define WLC_GET_FIXRATE 42 #define WLC_SET_FIXRATE 43 /* #define WLC_GET_WEP 42 */ /* no longer supported */ /* #define WLC_SET_WEP 43 */ /* no longer supported */ #define WLC_GET_KEY 44 #define WLC_SET_KEY 45 #define WLC_GET_REGULATORY 46 #define WLC_SET_REGULATORY 47 #define WLC_GET_PASSIVE_SCAN 48 #define WLC_SET_PASSIVE_SCAN 49 #define WLC_SCAN 50 #define WLC_SCAN_RESULTS 51 #define WLC_DISASSOC 52 #define WLC_REASSOC 53 #define WLC_GET_ROAM_TRIGGER 54 #define WLC_SET_ROAM_TRIGGER 55 #define WLC_GET_ROAM_DELTA 56 #define WLC_SET_ROAM_DELTA 57 #define WLC_GET_ROAM_SCAN_PERIOD 58 #define WLC_SET_ROAM_SCAN_PERIOD 59 #define WLC_EVM 60 /* diag */ #define WLC_GET_TXANT 61 #define WLC_SET_TXANT 62 #define WLC_GET_ANTDIV 63 #define WLC_SET_ANTDIV 64 /* #define WLC_GET_TXPWR 65 */ /* no longer supported */ /* #define WLC_SET_TXPWR 66 */ /* no longer supported */ #define WLC_GET_CLOSED 67 #define WLC_SET_CLOSED 68 #define WLC_GET_MACLIST 69 #define WLC_SET_MACLIST 70 #define WLC_GET_RATESET 71 #define WLC_SET_RATESET 72 /* #define WLC_GET_LOCALE 73 */ /* no longer supported */ #define WLC_LONGTRAIN 74 #define WLC_GET_BCNPRD 75 #define WLC_SET_BCNPRD 76 #define WLC_GET_DTIMPRD 77 #define WLC_SET_DTIMPRD 78 #define WLC_GET_SROM 79 #define WLC_SET_SROM 80 #define WLC_GET_WEP_RESTRICT 81 #define WLC_SET_WEP_RESTRICT 82 #define WLC_GET_COUNTRY 83 #define WLC_SET_COUNTRY 84 #define WLC_GET_PM 85 #define WLC_SET_PM 86 #define WLC_GET_WAKE 87 #define WLC_SET_WAKE 88 /* #define WLC_GET_D11CNTS 89 */ /* -> "counters" iovar */ #define WLC_GET_FORCELINK 90 /* ndis only */ #define WLC_SET_FORCELINK 91 /* ndis only */ #define WLC_FREQ_ACCURACY 92 /* diag */ #define WLC_CARRIER_SUPPRESS 93 /* diag */ #define WLC_GET_PHYREG 94 #define WLC_SET_PHYREG 95 #define WLC_GET_RADIOREG 96 #define WLC_SET_RADIOREG 97 #define WLC_GET_REVINFO 98 #define WLC_GET_UCANTDIV 99 #define WLC_SET_UCANTDIV 100 #define WLC_R_REG 101 #define WLC_W_REG 102 /* #define WLC_DIAG_LOOPBACK 103 old tray diag */ /* #define WLC_RESET_D11CNTS 104 */ /* -> "reset_d11cnts" iovar */ #define WLC_GET_MACMODE 105 #define WLC_SET_MACMODE 106 #define WLC_GET_MONITOR 107 #define WLC_SET_MONITOR 108 #define WLC_GET_GMODE 109 #define WLC_SET_GMODE 110 #define WLC_GET_LEGACY_ERP 111 #define WLC_SET_LEGACY_ERP 112 #define WLC_GET_RX_ANT 113 #define WLC_GET_CURR_RATESET 114 /* current rateset */ #define WLC_GET_SCANSUPPRESS 115 #define WLC_SET_SCANSUPPRESS 116 #define WLC_GET_AP 117 #define WLC_SET_AP 118 #define WLC_GET_EAP_RESTRICT 119 #define WLC_SET_EAP_RESTRICT 120 #define WLC_SCB_AUTHORIZE 121 #define WLC_SCB_DEAUTHORIZE 122 #define WLC_GET_WDSLIST 123 #define WLC_SET_WDSLIST 124 #define WLC_GET_ATIM 125 #define WLC_SET_ATIM 126 #define WLC_GET_RSSI 127 #define WLC_GET_PHYANTDIV 128 #define WLC_SET_PHYANTDIV 129 #define WLC_AP_RX_ONLY 130 #define WLC_GET_TX_PATH_PWR 131 #define WLC_SET_TX_PATH_PWR 132 #define WLC_GET_WSEC 133 #define WLC_SET_WSEC 134 #define WLC_GET_PHY_NOISE 135 #define WLC_GET_BSS_INFO 136 #define WLC_GET_PKTCNTS 137 #define WLC_GET_LAZYWDS 138 #define WLC_SET_LAZYWDS 139 #define WLC_GET_BANDLIST 140 #define WLC_GET_BAND 141 #define WLC_SET_BAND 142 #define WLC_SCB_DEAUTHENTICATE 143 #define WLC_GET_SHORTSLOT 144 #define WLC_GET_SHORTSLOT_OVERRIDE 145 #define WLC_SET_SHORTSLOT_OVERRIDE 146 #define WLC_GET_SHORTSLOT_RESTRICT 147 #define WLC_SET_SHORTSLOT_RESTRICT 148 #define WLC_GET_GMODE_PROTECTION 149 #define WLC_GET_GMODE_PROTECTION_OVERRIDE 150 #define WLC_SET_GMODE_PROTECTION_OVERRIDE 151 #define WLC_UPGRADE 152 /* #define WLC_GET_MRATE 153 */ /* no longer supported */ /* #define WLC_SET_MRATE 154 */ /* no longer supported */ #define WLC_GET_IGNORE_BCNS 155 #define WLC_SET_IGNORE_BCNS 156 #define WLC_GET_SCB_TIMEOUT 157 #define WLC_SET_SCB_TIMEOUT 158 #define WLC_GET_ASSOCLIST 159 #define WLC_GET_CLK 160 #define WLC_SET_CLK 161 #define WLC_GET_UP 162 #define WLC_OUT 163 #define WLC_GET_WPA_AUTH 164 #define WLC_SET_WPA_AUTH 165 #define WLC_GET_UCFLAGS 166 #define WLC_SET_UCFLAGS 167 #define WLC_GET_PWRIDX 168 #define WLC_SET_PWRIDX 169 #define WLC_GET_TSSI 170 #define WLC_GET_SUP_RATESET_OVERRIDE 171 #define WLC_SET_SUP_RATESET_OVERRIDE 172 /* #define WLC_SET_FAST_TIMER 173 */ /* no longer supported */ /* #define WLC_GET_FAST_TIMER 174 */ /* no longer supported */ /* #define WLC_SET_SLOW_TIMER 175 */ /* no longer supported */ /* #define WLC_GET_SLOW_TIMER 176 */ /* no longer supported */ /* #define WLC_DUMP_PHYREGS 177 */ /* no longer supported */ #define WLC_GET_PROTECTION_CONTROL 178 #define WLC_SET_PROTECTION_CONTROL 179 #define WLC_GET_PHYLIST 180 #define WLC_ENCRYPT_STRENGTH 181 /* ndis only */ #define WLC_DECRYPT_STATUS 182 /* ndis only */ #define WLC_GET_KEY_SEQ 183 #define WLC_GET_SCAN_CHANNEL_TIME 184 #define WLC_SET_SCAN_CHANNEL_TIME 185 #define WLC_GET_SCAN_UNASSOC_TIME 186 #define WLC_SET_SCAN_UNASSOC_TIME 187 #define WLC_GET_SCAN_HOME_TIME 188 #define WLC_SET_SCAN_HOME_TIME 189 #define WLC_GET_SCAN_NPROBES 190 #define WLC_SET_SCAN_NPROBES 191 #define WLC_GET_PRB_RESP_TIMEOUT 192 #define WLC_SET_PRB_RESP_TIMEOUT 193 #define WLC_GET_ATTEN 194 #define WLC_SET_ATTEN 195 #define WLC_GET_SHMEM 196 /* diag */ #define WLC_SET_SHMEM 197 /* diag */ /* #define WLC_GET_GMODE_PROTECTION_CTS 198 */ /* no longer supported */ /* #define WLC_SET_GMODE_PROTECTION_CTS 199 */ /* no longer supported */ #define WLC_SET_WSEC_TEST 200 #define WLC_SCB_DEAUTHENTICATE_FOR_REASON 201 #define WLC_TKIP_COUNTERMEASURES 202 #define WLC_GET_PIOMODE 203 #define WLC_SET_PIOMODE 204 #define WLC_SET_ASSOC_PREFER 205 #define WLC_GET_ASSOC_PREFER 206 #define WLC_SET_ROAM_PREFER 207 #define WLC_GET_ROAM_PREFER 208 /* #define WLC_SET_LED 209 */ /* no longer supported */ /* #define WLC_GET_LED 210 */ /* no longer supported */ #define WLC_GET_INTERFERENCE_MODE 211 #define WLC_SET_INTERFERENCE_MODE 212 #define WLC_GET_CHANNEL_QA 213 #define WLC_START_CHANNEL_QA 214 #define WLC_GET_CHANNEL_SEL 215 #define WLC_START_CHANNEL_SEL 216 #define WLC_GET_VALID_CHANNELS 217 #define WLC_GET_FAKEFRAG 218 #define WLC_SET_FAKEFRAG 219 #define WLC_GET_PWROUT_PERCENTAGE 220 #define WLC_SET_PWROUT_PERCENTAGE 221 #define WLC_SET_BAD_FRAME_PREEMPT 222 #define WLC_GET_BAD_FRAME_PREEMPT 223 #define WLC_SET_LEAP_LIST 224 #define WLC_GET_LEAP_LIST 225 #define WLC_GET_CWMIN 226 #define WLC_SET_CWMIN 227 #define WLC_GET_CWMAX 228 #define WLC_SET_CWMAX 229 #define WLC_GET_WET 230 #define WLC_SET_WET 231 #define WLC_GET_PUB 232 /* #define WLC_SET_GLACIAL_TIMER 233 */ /* no longer supported */ /* #define WLC_GET_GLACIAL_TIMER 234 */ /* no longer supported */ #define WLC_GET_KEY_PRIMARY 235 #define WLC_SET_KEY_PRIMARY 236 /* #define WLC_DUMP_RADIOREGS 237 */ /* no longer supported */ #define WLC_GET_ACI_ARGS 238 #define WLC_SET_ACI_ARGS 239 #define WLC_UNSET_CALLBACK 240 #define WLC_SET_CALLBACK 241 #define WLC_GET_RADAR 242 #define WLC_SET_RADAR 243 #define WLC_SET_SPECT_MANAGMENT 244 #define WLC_GET_SPECT_MANAGMENT 245 #define WLC_WDS_GET_REMOTE_HWADDR 246 /* handled in wl_linux.c/wl_vx.c */ #define WLC_WDS_GET_WPA_SUP 247 #define WLC_SET_CS_SCAN_TIMER 248 #define WLC_GET_CS_SCAN_TIMER 249 #define WLC_MEASURE_REQUEST 250 #define WLC_INIT 251 #define WLC_SEND_QUIET 252 #define WLC_KEEPALIVE 253 #define WLC_SEND_PWR_CONSTRAINT 254 #define WLC_UPGRADE_STATUS 255 #define WLC_CURRENT_PWR 256 #define WLC_GET_SCAN_PASSIVE_TIME 257 #define WLC_SET_SCAN_PASSIVE_TIME 258 #define WLC_LEGACY_LINK_BEHAVIOR 259 #define WLC_GET_CHANNELS_IN_COUNTRY 260 #define WLC_GET_COUNTRY_LIST 261 #define WLC_GET_VAR 262 /* get value of named variable */ #define WLC_SET_VAR 263 /* set named variable to value */ #define WLC_NVRAM_GET 264 /* deprecated */ #define WLC_NVRAM_SET 265 #define WLC_NVRAM_DUMP 266 #define WLC_REBOOT 267 #define WLC_SET_WSEC_PMK 268 #define WLC_GET_AUTH_MODE 269 #define WLC_SET_AUTH_MODE 270 #define WLC_GET_WAKEENTRY 271 #define WLC_SET_WAKEENTRY 272 #define WLC_NDCONFIG_ITEM 273 /* currently handled in wl_oid.c */ #define WLC_NVOTPW 274 #define WLC_OTPW 275 #define WLC_IOV_BLOCK_GET 276 #define WLC_IOV_MODULES_GET 277 #define WLC_SOFT_RESET 278 #define WLC_GET_ALLOW_MODE 279 #define WLC_SET_ALLOW_MODE 280 #define WLC_GET_DESIRED_BSSID 281 #define WLC_SET_DESIRED_BSSID 282 #define WLC_DISASSOC_MYAP 283 #define WLC_GET_NBANDS 284 /* for Dongle EXT_STA support */ #define WLC_GET_BANDSTATES 285 /* for Dongle EXT_STA support */ #define WLC_GET_WLC_BSS_INFO 286 /* for Dongle EXT_STA support */ #define WLC_GET_ASSOC_INFO 287 /* for Dongle EXT_STA support */ #define WLC_GET_OID_PHY 288 /* for Dongle EXT_STA support */ #define WLC_SET_OID_PHY 289 /* for Dongle EXT_STA support */ #define WLC_SET_ASSOC_TIME 290 /* for Dongle EXT_STA support */ #define WLC_GET_DESIRED_SSID 291 /* for Dongle EXT_STA support */ #define WLC_GET_CHANSPEC 292 /* for Dongle EXT_STA support */ #define WLC_GET_ASSOC_STATE 293 /* for Dongle EXT_STA support */ #define WLC_SET_PHY_STATE 294 /* for Dongle EXT_STA support */ #define WLC_GET_SCAN_PENDING 295 /* for Dongle EXT_STA support */ #define WLC_GET_SCANREQ_PENDING 296 /* for Dongle EXT_STA support */ #define WLC_GET_PREV_ROAM_REASON 297 /* for Dongle EXT_STA support */ #define WLC_SET_PREV_ROAM_REASON 298 /* for Dongle EXT_STA support */ #define WLC_GET_BANDSTATES_PI 299 /* for Dongle EXT_STA support */ #define WLC_GET_PHY_STATE 300 /* for Dongle EXT_STA support */ #define WLC_GET_BSS_WPA_RSN 301 /* for Dongle EXT_STA support */ #define WLC_GET_BSS_WPA2_RSN 302 /* for Dongle EXT_STA support */ #define WLC_GET_BSS_BCN_TS 303 /* for Dongle EXT_STA support */ #define WLC_GET_INT_DISASSOC 304 /* for Dongle EXT_STA support */ #define WLC_SET_NUM_PEERS 305 /* for Dongle EXT_STA support */ #define WLC_GET_NUM_BSS 306 /* for Dongle EXT_STA support */ #define WLC_PHY_SAMPLE_COLLECT 307 /* phy sample collect mode */ /* #define WLC_UM_PRIV 308 */ /* Deprecated: usermode driver */ #define WLC_GET_CMD 309 /* #define WLC_LAST 310 */ /* Never used - can be reused */ #define WLC_SET_INTERFERENCE_OVERRIDE_MODE 311 /* set inter mode override */ #define WLC_GET_INTERFERENCE_OVERRIDE_MODE 312 /* get inter mode override */ /* #define WLC_GET_WAI_RESTRICT 313 */ /* for WAPI, deprecated use iovar instead */ /* #define WLC_SET_WAI_RESTRICT 314 */ /* for WAPI, deprecated use iovar instead */ /* #define WLC_SET_WAI_REKEY 315 */ /* for WAPI, deprecated use iovar instead */ #define WLC_SET_NAT_CONFIG 316 /* for configuring NAT filter driver */ #define WLC_GET_NAT_STATE 317 #define WLC_GET_TXBF_RATESET 318 #define WLC_SET_TXBF_RATESET 319 #define WLC_SCAN_CQ 320 #define WLC_GET_RSSI_QDB 321 /* qdB portion of the RSSI */ #define WLC_DUMP_RATESET 322 #define WLC_ECHO 323 #define WLC_LAST 324 /* The last ioctl. Also push this * number when adding new ioctls */ /* * Alert: * Duplicate a few definitions that irelay requires from epiioctl.h here * so caller doesn't have to include this file and epiioctl.h . * If this grows any more, it would be time to move these irelay-specific * definitions out of the epiioctl.h and into a separate driver common file. */ #ifndef EPICTRL_COOKIE #define EPICTRL_COOKIE 0xABADCEDE #endif /* vx wlc ioctl's offset */ #define CMN_IOCTL_OFF 0x180 /* * custom OID support * * 0xFF - implementation specific OID * 0xE4 - first byte of Broadcom PCI vendor ID * 0x14 - second byte of Broadcom PCI vendor ID * 0xXX - the custom OID number */ /* begin 0x1f values beyond the start of the ET driver range. */ #define WL_OID_BASE 0xFFE41420 /* NDIS overrides */ #define OID_WL_GETINSTANCE (WL_OID_BASE + WLC_GET_INSTANCE) #define OID_WL_GET_FORCELINK (WL_OID_BASE + WLC_GET_FORCELINK) #define OID_WL_SET_FORCELINK (WL_OID_BASE + WLC_SET_FORCELINK) #define OID_WL_ENCRYPT_STRENGTH (WL_OID_BASE + WLC_ENCRYPT_STRENGTH) #define OID_WL_DECRYPT_STATUS (WL_OID_BASE + WLC_DECRYPT_STATUS) #define OID_LEGACY_LINK_BEHAVIOR (WL_OID_BASE + WLC_LEGACY_LINK_BEHAVIOR) #define OID_WL_NDCONFIG_ITEM (WL_OID_BASE + WLC_NDCONFIG_ITEM) /* EXT_STA Dongle suuport */ #define OID_STA_CHANSPEC (WL_OID_BASE + WLC_GET_CHANSPEC) #define OID_STA_NBANDS (WL_OID_BASE + WLC_GET_NBANDS) #define OID_STA_GET_PHY (WL_OID_BASE + WLC_GET_OID_PHY) #define OID_STA_SET_PHY (WL_OID_BASE + WLC_SET_OID_PHY) #define OID_STA_ASSOC_TIME (WL_OID_BASE + WLC_SET_ASSOC_TIME) #define OID_STA_DESIRED_SSID (WL_OID_BASE + WLC_GET_DESIRED_SSID) #define OID_STA_SET_PHY_STATE (WL_OID_BASE + WLC_SET_PHY_STATE) #define OID_STA_SCAN_PENDING (WL_OID_BASE + WLC_GET_SCAN_PENDING) #define OID_STA_SCANREQ_PENDING (WL_OID_BASE + WLC_GET_SCANREQ_PENDING) #define OID_STA_GET_ROAM_REASON (WL_OID_BASE + WLC_GET_PREV_ROAM_REASON) #define OID_STA_SET_ROAM_REASON (WL_OID_BASE + WLC_SET_PREV_ROAM_REASON) #define OID_STA_GET_PHY_STATE (WL_OID_BASE + WLC_GET_PHY_STATE) #define OID_STA_INT_DISASSOC (WL_OID_BASE + WLC_GET_INT_DISASSOC) #define OID_STA_SET_NUM_PEERS (WL_OID_BASE + WLC_SET_NUM_PEERS) #define OID_STA_GET_NUM_BSS (WL_OID_BASE + WLC_GET_NUM_BSS) /* NAT filter driver support */ #define OID_NAT_SET_CONFIG (WL_OID_BASE + WLC_SET_NAT_CONFIG) #define OID_NAT_GET_STATE (WL_OID_BASE + WLC_GET_NAT_STATE) #define WL_DECRYPT_STATUS_SUCCESS 1 #define WL_DECRYPT_STATUS_FAILURE 2 #define WL_DECRYPT_STATUS_UNKNOWN 3 /* allows user-mode app to poll the status of USB image upgrade */ #define WLC_UPGRADE_SUCCESS 0 #define WLC_UPGRADE_PENDING 1 /* WLC_GET_AUTH, WLC_SET_AUTH values */ #define WL_AUTH_OPEN_SYSTEM 0 /* d11 open authentication */ #define WL_AUTH_SHARED_KEY 1 /* d11 shared authentication */ #define WL_AUTH_OPEN_SHARED 2 /* try open, then shared if open failed w/rc 13 */ #define WL_AUTH_SAE_KEY 3 /* d11 sae authentication */ #define WL_AUTH_FILS_SHARED 4 /* d11 fils shared key authentication */ #define WL_AUTH_FILS_SHARED_PFS 5 /* d11 fils shared key w/ pfs authentication */ #define WL_AUTH_FILS_PUBLIC 6 /* d11 fils public key authentication */ /* Some branch use different define for WL_AUTH_OPEN_SHARED * for example, PHOENIX2 Branch defined WL_AUTH_OPEN_SHARED as 3 * But other branch defined WL_AUTH_OPEN_SHARED as 2 * if it is mismatch, WEP association can be failed. * More information - RB:5320 */ /* a large TX Power as an init value to factor out of MIN() calculations, * keep low enough to fit in an int8, units are .25 dBm */ #define WLC_TXPWR_MAX (127) /* ~32 dBm = 1,500 mW */ /* "diag" iovar argument and error code */ #define WL_DIAG_INTERRUPT 1 /* d11 loopback interrupt test */ #define WL_DIAG_LOOPBACK 2 /* d11 loopback data test */ #define WL_DIAG_MEMORY 3 /* d11 memory test */ #define WL_DIAG_LED 4 /* LED test */ #define WL_DIAG_REG 5 /* d11/phy register test */ #define WL_DIAG_SROM 6 /* srom read/crc test */ #define WL_DIAG_DMA 7 /* DMA test */ #define WL_DIAG_LOOPBACK_EXT 8 /* enhenced d11 loopback data test */ #define WL_DIAGERR_SUCCESS 0 #define WL_DIAGERR_FAIL_TO_RUN 1 /* unable to run requested diag */ #define WL_DIAGERR_NOT_SUPPORTED 2 /* diag requested is not supported */ #define WL_DIAGERR_INTERRUPT_FAIL 3 /* loopback interrupt test failed */ #define WL_DIAGERR_LOOPBACK_FAIL 4 /* loopback data test failed */ #define WL_DIAGERR_SROM_FAIL 5 /* srom read failed */ #define WL_DIAGERR_SROM_BADCRC 6 /* srom crc failed */ #define WL_DIAGERR_REG_FAIL 7 /* d11/phy register test failed */ #define WL_DIAGERR_MEMORY_FAIL 8 /* d11 memory test failed */ #define WL_DIAGERR_NOMEM 9 /* diag test failed due to no memory */ #define WL_DIAGERR_DMA_FAIL 10 /* DMA test failed */ #define WL_DIAGERR_MEMORY_TIMEOUT 11 /* d11 memory test didn't finish in time */ #define WL_DIAGERR_MEMORY_BADPATTERN 12 /* d11 memory test result in bad pattern */ /* band types */ #define WLC_BAND_AUTO 0 /* auto-select */ #define WLC_BAND_5G 1 /* 5 Ghz */ #define WLC_BAND_2G 2 /* 2.4 Ghz */ #define WLC_BAND_ALL 3 /* all bands */ #define WLC_BAND_6G 4 /* 6 Ghz */ #define WLC_BAND_INVALID -1 /* Invalid band */ #define WL_BAND_MAX_CNT 3 /* max number of bands supported */ /* band range returned by band_range iovar */ #define WL_CHAN_FREQ_RANGE_2G 0 #define WL_CHAN_FREQ_RANGE_5GL 1 #define WL_CHAN_FREQ_RANGE_5GM 2 #define WL_CHAN_FREQ_RANGE_5GH 3 #define WL_CHAN_FREQ_RANGE_5GLL_5BAND 4 #define WL_CHAN_FREQ_RANGE_5GLH_5BAND 5 #define WL_CHAN_FREQ_RANGE_5GML_5BAND 6 #define WL_CHAN_FREQ_RANGE_5GMH_5BAND 7 #define WL_CHAN_FREQ_RANGE_5GH_5BAND 8 #define WL_CHAN_FREQ_RANGE_5G_BAND0 1 #define WL_CHAN_FREQ_RANGE_5G_BAND1 2 #define WL_CHAN_FREQ_RANGE_5G_BAND2 3 #define WL_CHAN_FREQ_RANGE_5G_BAND3 4 #define WL_CHAN_FREQ_RANGE_5G_4BAND 5 #define WL_CHAN_FREQ_RANGE_6G_6BAND 6 /* SROM12 */ #define WL_CHAN_FREQ_RANGE_5G_BAND4 5 #define WL_CHAN_FREQ_RANGE_2G_40 6 #define WL_CHAN_FREQ_RANGE_5G_BAND0_40 7 #define WL_CHAN_FREQ_RANGE_5G_BAND1_40 8 #define WL_CHAN_FREQ_RANGE_5G_BAND2_40 9 #define WL_CHAN_FREQ_RANGE_5G_BAND3_40 10 #define WL_CHAN_FREQ_RANGE_5G_BAND4_40 11 #define WL_CHAN_FREQ_RANGE_5G_BAND0_80 12 #define WL_CHAN_FREQ_RANGE_5G_BAND1_80 13 #define WL_CHAN_FREQ_RANGE_5G_BAND2_80 14 #define WL_CHAN_FREQ_RANGE_5G_BAND3_80 15 #define WL_CHAN_FREQ_RANGE_5G_BAND4_80 16 #define WL_CHAN_FREQ_RANGE_5G_5BAND 18 #define WL_CHAN_FREQ_RANGE_5G_5BAND_40 19 #define WL_CHAN_FREQ_RANGE_5G_5BAND_80 20 #define WLC_MACMODE_DISABLED 0 /* MAC list disabled */ #define WLC_MACMODE_DENY 1 /* Deny specified (i.e. allow unspecified) */ #define WLC_MACMODE_ALLOW 2 /* Allow specified (i.e. deny unspecified) */ #define WLC_MACMODE_AVOID 3 /* Avoid specified (i.e. conditionally avoid unspecified) */ /* * 54g modes (basic bits may still be overridden) * * GMODE_LEGACY_B Rateset: 1b, 2b, 5.5, 11 * Preamble: Long * Shortslot: Off * GMODE_AUTO Rateset: 1b, 2b, 5.5b, 11b, 18, 24, 36, 54 * Extended Rateset: 6, 9, 12, 48 * Preamble: Long * Shortslot: Auto * GMODE_ONLY Rateset: 1b, 2b, 5.5b, 11b, 18, 24b, 36, 54 * Extended Rateset: 6b, 9, 12b, 48 * Preamble: Short required * Shortslot: Auto * GMODE_B_DEFERRED Rateset: 1b, 2b, 5.5b, 11b, 18, 24, 36, 54 * Extended Rateset: 6, 9, 12, 48 * Preamble: Long * Shortslot: On * GMODE_PERFORMANCE Rateset: 1b, 2b, 5.5b, 6b, 9, 11b, 12b, 18, 24b, 36, 48, 54 * Preamble: Short required * Shortslot: On and required * GMODE_LRS Rateset: 1b, 2b, 5.5b, 11b * Extended Rateset: 6, 9, 12, 18, 24, 36, 48, 54 * Preamble: Long * Shortslot: Auto */ #define GMODE_LEGACY_B 0 #define GMODE_AUTO 1 #define GMODE_ONLY 2 #define GMODE_B_DEFERRED 3 #define GMODE_PERFORMANCE 4 #define GMODE_LRS 5 #define GMODE_MAX 6 /* values for PLCPHdr_override */ #define WLC_PLCP_AUTO -1 #define WLC_PLCP_SHORT 0 #define WLC_PLCP_LONG 1 /* values for g_protection_override and n_protection_override */ #define WLC_PROTECTION_AUTO -1 #define WLC_PROTECTION_OFF 0 #define WLC_PROTECTION_ON 1 #define WLC_PROTECTION_MMHDR_ONLY 2 #define WLC_PROTECTION_CTS_ONLY 3 /* values for g_protection_control and n_protection_control */ #define WLC_PROTECTION_CTL_OFF 0 #define WLC_PROTECTION_CTL_LOCAL 1 #define WLC_PROTECTION_CTL_OVERLAP 2 /* values for n_protection */ #define WLC_N_PROTECTION_OFF 0 #define WLC_N_PROTECTION_OPTIONAL 1 #define WLC_N_PROTECTION_20IN40 2 #define WLC_N_PROTECTION_MIXEDMODE 3 /* values for n_preamble_type */ #define WLC_N_PREAMBLE_MIXEDMODE 0 #define WLC_N_PREAMBLE_GF 1 #define WLC_N_PREAMBLE_GF_BRCM 2 /* values for band specific 40MHz capabilities (deprecated) */ #define WLC_N_BW_20ALL 0 #define WLC_N_BW_40ALL 1 #define WLC_N_BW_20IN2G_40IN5G 2 #define WLC_BW_20MHZ_BIT (1<<0) #define WLC_BW_40MHZ_BIT (1<<1) #define WLC_BW_80MHZ_BIT (1<<2) #define WLC_BW_160MHZ_BIT (1<<3) #define WLC_BW_320MHZ_BIT (1u<<4u) /* Bandwidth capabilities */ #define WLC_BW_CAP_20MHZ (WLC_BW_20MHZ_BIT) #define WLC_BW_CAP_40MHZ (WLC_BW_40MHZ_BIT|WLC_BW_20MHZ_BIT) #define WLC_BW_CAP_80MHZ (WLC_BW_80MHZ_BIT|WLC_BW_40MHZ_BIT| \ WLC_BW_20MHZ_BIT) #define WLC_BW_CAP_160MHZ (WLC_BW_160MHZ_BIT|WLC_BW_80MHZ_BIT| \ WLC_BW_40MHZ_BIT|WLC_BW_20MHZ_BIT) #define WLC_BW_CAP_320MHZ (WLC_BW_320MHZ_BIT| \ WLC_BW_160MHZ_BIT|WLC_BW_80MHZ_BIT| \ WLC_BW_40MHZ_BIT|WLC_BW_20MHZ_BIT) #define WLC_BW_CAP_UNRESTRICTED 0xFF #define WL_BW_CAP_20MHZ(bw_cap) (((bw_cap) & WLC_BW_20MHZ_BIT) ? TRUE : FALSE) #define WL_BW_CAP_40MHZ(bw_cap) (((bw_cap) & WLC_BW_40MHZ_BIT) ? TRUE : FALSE) #define WL_BW_CAP_80MHZ(bw_cap) (((bw_cap) & WLC_BW_80MHZ_BIT) ? TRUE : FALSE) #define WL_BW_CAP_160MHZ(bw_cap) (((bw_cap) & WLC_BW_160MHZ_BIT) ? TRUE : FALSE) #define WL_BW_CAP_320MHZ(bw_cap) (((bw_cap) & WLC_BW_320MHZ_BIT) ? TRUE : FALSE) /* values to force tx/rx chain */ #define WLC_N_TXRX_CHAIN0 0 #define WLC_N_TXRX_CHAIN1 1 /* bitflags for SGI support (sgi_rx iovar) */ #define WLC_N_SGI_20 0x01 #define WLC_N_SGI_40 0x02 #define WLC_VHT_SGI_80 0x04 #define WLC_VHT_SGI_160 0x08 /* when sgi_tx==WLC_SGI_ALL, bypass rate selection, enable sgi for all mcs */ #define WLC_SGI_ALL 0x02 #define LISTEN_INTERVAL 10 /* interference mitigation options */ #define INTERFERE_OVRRIDE_OFF -1 /* interference override off */ #define INTERFERE_NONE 0 /* off */ #define NON_WLAN 1 /* foreign/non 802.11 interference, no auto detect */ #define WLAN_MANUAL 2 /* ACI: no auto detection */ #define WLAN_AUTO 3 /* ACI: auto detect */ #define WLAN_AUTO_W_NOISE 4 /* ACI: auto - detect and non 802.11 interference */ #define AUTO_ACTIVE (1 << 7) /* Auto is currently active */ /* interfernece mode bit-masks (ACPHY) */ #define ACPHY_ACI_GLITCHBASED_DESENSE 1 /* bit 0 */ #define ACPHY_ACI_HWACI_PKTGAINLMT 2 /* bit 1 */ #define ACPHY_ACI_W2NB_PKTGAINLMT 4 /* bit 2 */ #define ACPHY_ACI_PREEMPTION 8 /* bit 3 */ #define ACPHY_HWACI_MITIGATION 16 /* bit 4 */ #define ACPHY_LPD_PREEMPTION 32 /* bit 5 */ #define ACPHY_HWOBSS_MITIGATION 64 /* bit 6 */ #define ACPHY_ACI_MAX_MODE 127 /* AP environment */ #define AP_ENV_DETECT_NOT_USED 0 /* We aren't using AP environment detection */ #define AP_ENV_DENSE 1 /* "Corporate" or other AP dense environment */ #define AP_ENV_SPARSE 2 /* "Home" or other sparse environment */ #define AP_ENV_INDETERMINATE 3 /* AP environment hasn't been identified */ #define TRIGGER_NOW 0 #define TRIGGER_CRS 0x01 #define TRIGGER_CRSDEASSERT 0x02 #define TRIGGER_GOODFCS 0x04 #define TRIGGER_BADFCS 0x08 #define TRIGGER_BADPLCP 0x10 #define TRIGGER_CRSGLITCH 0x20 #define TRIGGER_ASYNC 0x40 #define WL_SAMPLEDATA_HEADER_TYPE 1 #define WL_SAMPLEDATA_HEADER_SIZE 80 /* sample collect header size (bytes) */ #define WL_SAMPLEDATA_TYPE 2 #define WL_SAMPLEDATA_SEQ 0xff /* sequence # */ #define WL_SAMPLEDATA_MORE_DATA 0x100 /* more data mask */ /* WL_OTA START */ #define WL_OTA_ARG_PARSE_BLK_SIZE 1200 #define WL_OTA_TEST_MAX_NUM_RATE 30 #define WL_OTA_TEST_MAX_NUM_SEQ 100 #define WL_OTA_TEST_MAX_NUM_RSSI 85 #define WL_THRESHOLD_LO_BAND 70 /* range from 5250MHz - 5350MHz */ /* radar iovar SET defines */ #define WL_RADAR_DETECTOR_OFF 0 /* radar detector off */ #define WL_RADAR_DETECTOR_ON 1 /* radar detector on */ #define WL_RADAR_SIMULATED 2 /* force radar detector to declare * detection once */ #define WL_RADAR_SIMULATED_SC 3 /* force radar detector to declare * detection once on scan core * if available and active */ #define WL_RSSI_ANT_VERSION 1 /* current version of wl_rssi_ant_t */ #define WL_ANT_RX_MAX 2 /* max 2 receive antennas */ #define WL_ANT_HT_RX_MAX 4 /* max 4 receive antennas/cores */ #define WL_ANT_IDX_1 0 /* antenna index 1 */ #define WL_ANT_IDX_2 1 /* antenna index 2 */ #ifndef WL_RSSI_ANT_MAX #define WL_RSSI_ANT_MAX 4 /* max possible rx antennas */ #elif WL_RSSI_ANT_MAX != 4 #error "WL_RSSI_ANT_MAX does not match" #endif /* dfs_status iovar-related defines */ /* cac - channel availability check, * ism - in-service monitoring * csa - channel switching announcement */ /* cac state values */ #define WL_DFS_CACSTATE_IDLE 0 /* state for operating in non-radar channel */ #define WL_DFS_CACSTATE_PREISM_CAC 1 /* CAC in progress */ #define WL_DFS_CACSTATE_ISM 2 /* ISM in progress */ #define WL_DFS_CACSTATE_CSA 3 /* csa */ #define WL_DFS_CACSTATE_POSTISM_CAC 4 /* ISM CAC */ #define WL_DFS_CACSTATE_PREISM_OOC 5 /* PREISM OOC */ #define WL_DFS_CACSTATE_POSTISM_OOC 6 /* POSTISM OOC */ #define WL_DFS_CACSTATES 7 /* this many states exist */ /* Defines used with channel_bandwidth for curpower */ #define WL_BW_20MHZ 0 #define WL_BW_40MHZ 1 #define WL_BW_80MHZ 2 #define WL_BW_160MHZ 3 #define WL_BW_8080MHZ 4 #define WL_BW_2P5MHZ 5 #define WL_BW_5MHZ 6 #define WL_BW_10MHZ 7 #define WL_BW_320MHZ 8u /* tx_power_t.flags bits */ #define WL_TX_POWER_F_ENABLED 1 #define WL_TX_POWER_F_HW 2 #define WL_TX_POWER_F_MIMO 4 #define WL_TX_POWER_F_SISO 8 #define WL_TX_POWER_F_HT 0x10 #define WL_TX_POWER_F_VHT 0x20 #define WL_TX_POWER_F_OPENLOOP 0x40 #define WL_TX_POWER_F_PROP11NRATES 0x80 #define WL_TX_POWER_F_UNIT_QDBM 0x100 #define WL_TX_POWER_F_TXCAP 0x200 #define WL_TX_POWER_F_HE 0x400 #define WL_TX_POWER_F_RU_RATE 0x800 #define WL_TX_POWER_TPE_PSD 0x1000 #define WL_TX_POWER_TPE_LOC 0x2000 /* Message levels */ #define WL_ERROR_VAL 0x00000001 #define WL_TRACE_VAL 0x00000002 #define WL_PRHDRS_VAL 0x00000004 #define WL_PRPKT_VAL 0x00000008 #define WL_INFORM_VAL 0x00000010 #define WL_TMP_VAL 0x00000020 #define WL_OID_VAL 0x00000040 #define WL_RATE_VAL 0x00000080 #define WL_ASSOC_VAL 0x00000100 #define WL_PRUSR_VAL 0x00000200 #define WL_PS_VAL 0x00000400 #define WL_TXPWR_VAL 0x00000000 /* retired in TOT on 6/10/2009 */ #define WL_MODE_SWITCH_VAL 0x00000800 /* Using retired TXPWR val */ #define WL_PORT_VAL 0x00001000 #define WL_DUAL_VAL 0x00002000 #define WL_WSEC_VAL 0x00004000 #define WL_WSEC_DUMP_VAL 0x00008000 #define WL_LOG_VAL 0x00010000 #define WL_NRSSI_VAL 0x00000000 /* retired in TOT on 6/10/2009 */ #define WL_BCNTRIM_VAL 0x00020000 /* Using retired NRSSI VAL */ #define WL_LOFT_VAL 0x00000000 /* retired in TOT on 6/10/2009 */ #define WL_PFN_VAL 0x00040000 /* Using retired LOFT_VAL */ #define WL_REGULATORY_VAL 0x00080000 #define WL_CSA_VAL 0x00080000 /* Reusing REGULATORY_VAL due to lackof bits */ #define WL_TAF_VAL 0x00100000 #define WL_RADAR_VAL 0x00000000 /* retired in TOT on 6/10/2009 */ #define WL_WDI_VAL 0x00200000 /* Using retired WL_RADAR_VAL VAL */ #define WL_MPC_VAL 0x00400000 #define WL_APSTA_VAL 0x00800000 #define WL_DFS_VAL 0x01000000 #define WL_BA_VAL 0x00000000 /* retired in TOT on 6/14/2010 */ #define WL_MUMIMO_VAL 0x02000000 /* Using retired WL_BA_VAL */ #define WL_ACI_VAL 0x04000000 #define WL_PRMAC_VAL 0x04000000 #define WL_MBSS_VAL 0x04000000 #define WL_CAC_VAL 0x08000000 #define WL_AMSDU_VAL 0x10000000 #define WL_AMPDU_VAL 0x20000000 #define WL_FFPLD_VAL 0x40000000 #define WL_ROAM_EXP_VAL 0x80000000 /* wl_msg_level is full. For new bits take the next one and AND with * wl_msg_level2 in wl_dbg.h */ #define WL_DPT_VAL 0x00000001 /* re-using WL_DPT_VAL */ /* re-using WL_MESH_VAL */ #define WL_NATOE_VAL 0x00000001 #define WL_MESH_VAL 0x00000001 #define WL_SCAN_VAL 0x00000002 #define WL_WOWL_VAL 0x00000004 #define WL_COEX_VAL 0x00000008 #define WL_RTDC_VAL 0x00000010 #define WL_PROTO_VAL 0x00000020 #define WL_SWDIV_VAL 0x00000040 #define WL_CHANINT_VAL 0x00000080 #define WL_WMF_VAL 0x00000100 #define WL_P2P_VAL 0x00000200 #define WL_ITFR_VAL 0x00000400 #define WL_MCHAN_VAL 0x00000800 #define WL_TDLS_VAL 0x00001000 #define WL_MCNX_VAL 0x00002000 #define WL_PROT_VAL 0x00004000 #define WL_TSO_VAL 0x00010000 #define WL_TRF_MGMT_VAL 0x00020000 #define WL_LPC_VAL 0x00040000 #define WL_L2FILTER_VAL 0x00080000 #define WL_TXBF_VAL 0x00100000 #define WL_P2PO_VAL 0x00200000 #define WL_TBTT_VAL 0x00400000 #define WL_FBT_VAL 0x00800000 #define WL_RRM_VAL 0x00800000 /* reuse */ #define WL_MQ_VAL 0x01000000 #define WL_RANDMAC_VAL 0x02000000 #define WL_WNM_VAL 0x04000000 /* re-using WL_WNM_VAL for MBO */ #define WL_MBO_VAL 0x04000000 #define WL_NET_DETECT_VAL 0x20000000 #define WL_OCE_VAL 0x20000000 /* reuse */ #define WL_PCIE_VAL 0x40000000 #define WL_PMDUR_VAL 0x80000000 /* use top-bit for WL_TIME_STAMP_VAL because this is a modifier * rather than a message-type of its own */ #define WL_TIMESTAMP_VAL 0x80000000 /* wl_msg_level2 is full. For new bits take the next one and AND with * wl_msg_level3 in wl_dbg.h */ #define WL_ASSOC_AP_VAL 0x00000001 #define WL_FILS_VAL 0x00000002 #define WL_LATENCY_VAL 0x00000004 #define WL_WBUS_VAL 0x00000008 #define WL_DTPC_DBG_VAL 0x00000010 /* number of bytes needed to define a proper bit mask for MAC event reporting */ #define BCMIO_ROUNDUP(x, y) ((((x) + ((y) - 1)) / (y)) * (y)) #define BCMIO_NBBY 8 #define WL_EVENTING_MASK_LEN 16 /* Don't increase this without wl review */ #define WL_EVENTING_MASK_EXT_LEN ROUNDUP(WLC_E_LAST, NBBY)/NBBY /* join preference types */ #define WL_JOIN_PREF_RSSI 1u /* by RSSI */ #define WL_JOIN_PREF_WPA 2u /* by akm and ciphers */ #define WL_JOIN_PREF_BAND 3u /* by 802.11 band */ #define WL_JOIN_PREF_RSSI_DELTA 4u /* by 802.11 band only if RSSI * delta condition matches */ #define WL_JOIN_PREF_TRANS_PREF 5u /* defined by requesting AP */ #define WL_JOIN_PREF_RSN_PRIO 6u /* by RSNE/RSNXE related security priority */ #define WL_JOIN_PREF_RSSI_PER_BAND 7u /* RSSI boost value per band */ #define WL_JOIN_PREF_SKIP_PSC 8u /* Used to set flag to filter PSC channel scan */ #define WL_JOIN_PREF_6G_DISABLE 9u /* Used to disable join/roam 6G BSS target */ /* Join preference 6G disable Flag definition */ #define WL_JP_6G_DISABLE_ROAM (1u << 0u) /* Used to set flag to disable join/roam to 6G BSS target */ /* Join preference skip PSC Flag definition */ #define WL_JP_SKIP_PSC_ROAM (1u << 0u) /* Used to set flag to filter PSC channel during full band roam scan */ /* Join preference RSN priority */ #define WL_JP_RSN_SAE_PK 1u /* SAE-PK higher priority over non SAE-PK APs */ /* band preference */ #define WLJP_BAND_ASSOC_PREF 255 /* use what WLC_SET_ASSOC_PREFER ioctl specifies */ /* any multicast cipher suite */ #define WL_WPA_ACP_MCS_ANY "\x00\x00\x00\x00" /* 802.11h measurement types */ #define WLC_MEASURE_TPC 1 #define WLC_MEASURE_CHANNEL_BASIC 2 #define WLC_MEASURE_CHANNEL_CCA 3 #define WLC_MEASURE_CHANNEL_RPI 4 /* regulatory enforcement levels */ #define SPECT_MNGMT_OFF 0 /* both 11h and 11d disabled */ #define SPECT_MNGMT_LOOSE_11H 1 /* allow non-11h APs in scan lists */ #define SPECT_MNGMT_STRICT_11H 2 /* prune out non-11h APs from scan list */ #define SPECT_MNGMT_STRICT_11D 3 /* switch to 802.11D mode */ /* SPECT_MNGMT_LOOSE_11H_D - same as SPECT_MNGMT_LOOSE with the exception that Country IE * adoption is done regardless of capability spectrum_management */ #define SPECT_MNGMT_LOOSE_11H_D 4 /* operation defined above */ /* bit position in per_chan_info; these depend on current country/regulatory domain */ #define WL_CHAN_VALID_HW (1u << 0) /* valid with current HW */ #define WL_CHAN_VALID_SW (1u << 1) /* valid with current country setting */ #define WL_CHAN_BAND_5G (1u << 2) /* 5GHz-band channel */ #define WL_CHAN_RADAR (1u << 3) /* radar sensitive channel */ #define WL_CHAN_INACTIVE (1u << 4) /* temporarily inactive due to radar */ #define WL_CHAN_PASSIVE (1u << 5) /* channel is in passive mode */ #define WL_CHAN_RESTRICTED (1u << 6) /* restricted use channel */ #define WL_CHAN_RADAR_EU_WEATHER (1u << 7) /* EU Radar weather channel. * Implies an EU Radar channel. */ #define WL_CHAN_CLM_RESTRICTED (1u << 8) /* channel restricted in CLM (i.e. by default) */ #define WL_CHAN_BAND_6G (1u << 9) /* 6GHz-band channel */ #define WL_CHAN_BAND_6G_VLP (1u << 10u) /* 6GHz VLP channel */ #define WL_CHAN_BAND_6G_PSC (1u << 11u) /* 6GHz PSC channel */ #define WL_CHAN_BAND_6G_LPI (1u << 12u) /* 6GHz LPI channel */ #define WL_CHAN_BAND_6G_SP (1u << 13u) /* 6GHz SP channel */ #define WL_CHAN_OOS_SHIFT 24u /* shift for OOS field */ #define WL_CHAN_OOS_MASK 0xFF000000u /* field specifying minutes remaining for this * channel's out-of-service period due to radar * detection */ /* BTC mode used by "btc_mode" iovar */ #define WL_BTC_DISABLE 0 /* disable BT coexistence */ #define WL_BTC_FULLTDM 1 /* full TDM COEX */ #define WL_BTC_ENABLE 1 /* full TDM COEX to maintain backward compatiblity */ #define WL_BTC_PREMPT 2 /* full TDM COEX with preemption */ #define WL_BTC_LITE 3 /* light weight coex for large isolation platform */ #define WL_BTC_PARALLEL 4 /* BT and WLAN run in parallel with separate antenna */ #define WL_BTC_HYBRID 5 /* hybrid coex, only ack allowed to transmit in BT slot */ #define WL_BTC_HYBRID_WLTX 6 /* hybrid coex HPP mode w WL data Tx during BT grant */ #define WL_BTC_DEFAULT 8 /* set the default mode for the device */ #define WL_INF_BTC_DISABLE 0 #define WL_INF_BTC_ENABLE 1 #define WL_INF_BTC_AUTO 3 #define WL_BTC_MODE_IOV_2G_MASK 0xFFu #define WL_BTC_MODE_IOV_5G_MASK 0xFF00u #define WL_BTC_MODE_IOV_5G_SHIFT 0x8u /* BTC wire used by "btc_wire" iovar */ #define WL_BTC_DEFWIRE 0 /* use default wire setting */ #define WL_BTC_2WIRE 2 /* use 2-wire BTC */ #define WL_BTC_3WIRE 3 /* use 3-wire BTC */ #define WL_BTC_4WIRE 4 /* use 4-wire BTC */ /* BTC flags: BTC configuration that can be set by host */ #define WL_BTC_FLAG_PREMPT (1 << 0) #define WL_BTC_FLAG_BT_DEF (1 << 1) #define WL_BTC_FLAG_ACTIVE_PROT (1 << 2) #define WL_BTC_FLAG_SIM_RSP (1 << 3) #define WL_BTC_FLAG_PS_PROTECT (1 << 4) #define WL_BTC_FLAG_SIM_TX_LP (1 << 5) #define WL_BTC_FLAG_ECI (1 << 6) #define WL_BTC_FLAG_LIGHT (1 << 7) #define WL_BTC_FLAG_PARALLEL (1 << 8) /* maximum channels returned by the get valid channels iovar */ #define WL_NUMCHANNELS 64 /* This constant is obsolete, not part of ioctl/iovar interface and should never be used * It is preserved only for compatibility with older branches that use it */ #ifdef WL_BAND6G #ifdef WL_BAND5P9G #ifdef WL11AC_80P80 #define WL_NUMCHANSPECS 466 #else #define WL_NUMCHANSPECS 370 #endif #else #ifdef WL11AC_80P80 #define WL_NUMCHANSPECS 446 #else #define WL_NUMCHANSPECS 350 #endif #endif /* WL_BAND5P9G */ #else #if defined(WL11AC_80P80) #define WL_NUMCHANSPECS 206 #elif defined(WL_BW160MHZ) #define WL_NUMCHANSPECS 140 #else #define WL_NUMCHANSPECS 110 #endif #endif /* WL_BAND6G */ /* WDS link local endpoint WPA role */ #define WL_WDS_WPA_ROLE_AUTH 0 /* authenticator */ #define WL_WDS_WPA_ROLE_SUP 1 /* supplicant */ #define WL_WDS_WPA_ROLE_AUTO 255 /* auto, based on mac addr value */ /* Base offset values */ #define WL_PKT_FILTER_BASE_PKT 0 #define WL_PKT_FILTER_BASE_END 1 #define WL_PKT_FILTER_BASE_D11_H 2 /* May be removed */ #define WL_PKT_FILTER_BASE_D11_D 3 /* May be removed */ #define WL_PKT_FILTER_BASE_ETH_H 4 #define WL_PKT_FILTER_BASE_ETH_D 5 #define WL_PKT_FILTER_BASE_ARP_H 6 #define WL_PKT_FILTER_BASE_ARP_D 7 /* May be removed */ #define WL_PKT_FILTER_BASE_IP4_H 8 #define WL_PKT_FILTER_BASE_IP4_D 9 #define WL_PKT_FILTER_BASE_IP6_H 10 #define WL_PKT_FILTER_BASE_IP6_D 11 #define WL_PKT_FILTER_BASE_TCP_H 12 #define WL_PKT_FILTER_BASE_TCP_D 13 /* May be removed */ #define WL_PKT_FILTER_BASE_UDP_H 14 #define WL_PKT_FILTER_BASE_UDP_D 15 #define WL_PKT_FILTER_BASE_IP6_P 16 #define WL_PKT_FILTER_BASE_COUNT 17 /* May be removed */ /* String mapping for bases that may be used by applications or debug */ #define WL_PKT_FILTER_BASE_NAMES \ { "START", WL_PKT_FILTER_BASE_PKT }, \ { "END", WL_PKT_FILTER_BASE_END }, \ { "ETH_H", WL_PKT_FILTER_BASE_ETH_H }, \ { "ETH_D", WL_PKT_FILTER_BASE_ETH_D }, \ { "D11_H", WL_PKT_FILTER_BASE_D11_H }, \ { "D11_D", WL_PKT_FILTER_BASE_D11_D }, \ { "ARP_H", WL_PKT_FILTER_BASE_ARP_H }, \ { "IP4_H", WL_PKT_FILTER_BASE_IP4_H }, \ { "IP4_D", WL_PKT_FILTER_BASE_IP4_D }, \ { "IP6_H", WL_PKT_FILTER_BASE_IP6_H }, \ { "IP6_D", WL_PKT_FILTER_BASE_IP6_D }, \ { "IP6_P", WL_PKT_FILTER_BASE_IP6_P }, \ { "TCP_H", WL_PKT_FILTER_BASE_TCP_H }, \ { "TCP_D", WL_PKT_FILTER_BASE_TCP_D }, \ { "UDP_H", WL_PKT_FILTER_BASE_UDP_H }, \ { "UDP_D", WL_PKT_FILTER_BASE_UDP_D } /* Flags for a pattern list element */ #define WL_PKT_FILTER_MFLAG_NEG 0x0001 /* * Packet engine interface */ #define WL_PKTENG_PER_TX_START 0x01 #define WL_PKTENG_PER_TX_STOP 0x02 #define WL_PKTENG_PER_RX_START 0x04 #define WL_PKTENG_PER_RX_WITH_ACK_START 0x05 #define WL_PKTENG_PER_TX_WITH_ACK_START 0x06 #define WL_PKTENG_PER_RX_STOP 0x08 #define WL_PKTENG_PER_RU_TX_START 0x09 #define WL_PKTENG_PER_TRIG_TX_START 0x0a #define WL_PKTENG_PER_MASK 0xff #define WL_PKTENG_SYNCHRONOUS 0x100 /* synchronous flag */ #define WL_PKTENG_SYNCHRONOUS_UNBLK 0x200 /* synchronous unblock flag */ #define WL_PKTENG_COLLECT 0x400 /* Save last Rx'ed packet */ #ifdef PKTENG_LONGPKTSZ /* max pktsz limit for pkteng */ #define WL_PKTENG_MAXPKTSZ PKTENG_LONGPKTSZ #else #define WL_PKTENG_MAXPKTSZ 16384 #endif #define NUM_80211b_RATES 4 #define NUM_80211ag_RATES 8 #define NUM_80211n_RATES 32 #define NUM_80211_RATES (NUM_80211b_RATES+NUM_80211ag_RATES+NUM_80211n_RATES) /* * WOWL capability/override settings */ #define WL_WOWL_MAGIC (1 << 0) /* Wakeup on Magic packet */ #define WL_WOWL_NET (1 << 1) /* Wakeup on Netpattern */ #define WL_WOWL_DIS (1 << 2) /* Wakeup on loss-of-link due to Disassoc/Deauth */ #define WL_WOWL_RETR (1 << 3) /* Wakeup on retrograde TSF */ #define WL_WOWL_BCN (1 << 4) /* Wakeup on loss of beacon */ #define WL_WOWL_TST (1 << 5) /* Wakeup after test */ #define WL_WOWL_M1 (1 << 6) /* Wakeup after PTK refresh */ #define WL_WOWL_EAPID (1 << 7) /* Wakeup after receipt of EAP-Identity Req */ #define WL_WOWL_PME_GPIO (1 << 8) /* Wakeind via PME(0) or GPIO(1) */ #define WL_WOWL_ULP_BAILOUT (1 << 8) /* wakeind via unknown pkt by basic ULP-offloads - * WL_WOWL_ULP_BAILOUT - same as WL_WOWL_PME_GPIO used only for DONGLE BUILDS */ #define WL_WOWL_NEEDTKIP1 (1 << 9) /* need tkip phase 1 key to be updated by the driver */ #define WL_WOWL_GTK_FAILURE (1 << 10) /* enable wakeup if GTK fails */ #define WL_WOWL_EXTMAGPAT (1 << 11) /* support extended magic packets */ #define WL_WOWL_ARPOFFLOAD (1 << 12) /* support ARP/NS/keepalive offloading */ #define WL_WOWL_WPA2 (1 << 13) /* read protocol version for EAPOL frames */ #define WL_WOWL_KEYROT (1 << 14) /* If the bit is set, use key rotaton */ #define WL_WOWL_BCAST (1 << 15) /* If the bit is set, frm received was bcast frame */ #define WL_WOWL_SCANOL (1 << 16) /* If the bit is set, scan offload is enabled */ #define WL_WOWL_TCPKEEP_TIME (1 << 17) /* Wakeup on tcpkeep alive timeout */ #define WL_WOWL_MDNS_CONFLICT (1 << 18) /* Wakeup on mDNS Conflict Resolution */ #define WL_WOWL_MDNS_SERVICE (1 << 19) /* Wakeup on mDNS Service Connect */ #define WL_WOWL_TCPKEEP_DATA (1 << 20) /* tcp keepalive got data */ #define WL_WOWL_FW_HALT (1 << 21) /* Firmware died in wowl mode */ #define WL_WOWL_ENAB_HWRADIO (1 << 22) /* Enable detection of radio button changes */ #define WL_WOWL_MIC_FAIL (1 << 23) /* Offloads detected MIC failure(s) */ #define WL_WOWL_UNASSOC (1 << 24) /* Wakeup in Unassociated state (Net/Magic Pattern) */ #define WL_WOWL_SECURE (1 << 25) /* Wakeup if received matched secured pattern */ #define WL_WOWL_EXCESS_WAKE (1 << 26) /* Excess wake */ #define WL_WOWL_LINKDOWN (1 << 31) /* Link Down indication in WoWL mode */ #define WL_WOWL_TCPKEEP (1 << 20) /* temp copy to satisfy automerger */ #define MAGIC_PKT_MINLEN 102 /* Magic pkt min length is 6 * 0xFF + 16 * ETHER_ADDR_LEN */ #define WOWL_PATTEN_TYPE_ARP (1 << 0) /* ARP offload Pattern */ #define WOWL_PATTEN_TYPE_NA (1 << 1) /* NA offload Pattern */ #define MAGIC_PKT_MINLEN 102 /* Magic pkt min length is 6 * 0xFF + 16 * ETHER_ADDR_LEN */ #define MAGIC_PKT_NUM_MAC_ADDRS 16 /* Overlap BSS Scan parameters default, minimum, maximum */ #define WLC_OBSS_SCAN_PASSIVE_DWELL_DEFAULT 20 /* unit TU */ #define WLC_OBSS_SCAN_PASSIVE_DWELL_MIN 5 /* unit TU */ #define WLC_OBSS_SCAN_PASSIVE_DWELL_MAX 1000 /* unit TU */ #define WLC_OBSS_SCAN_ACTIVE_DWELL_DEFAULT 10 /* unit TU */ #define WLC_OBSS_SCAN_ACTIVE_DWELL_MIN 10 /* unit TU */ #define WLC_OBSS_SCAN_ACTIVE_DWELL_MAX 1000 /* unit TU */ #define WLC_OBSS_SCAN_WIDTHSCAN_INTERVAL_DEFAULT 300 /* unit Sec */ #define WLC_OBSS_SCAN_WIDTHSCAN_INTERVAL_MIN 10 /* unit Sec */ #define WLC_OBSS_SCAN_WIDTHSCAN_INTERVAL_MAX 900 /* unit Sec */ #define WLC_OBSS_SCAN_CHANWIDTH_TRANSITION_DLY_DEFAULT 5 #define WLC_OBSS_SCAN_CHANWIDTH_TRANSITION_DLY_MIN 5 #define WLC_OBSS_SCAN_CHANWIDTH_TRANSITION_DLY_MAX 100 #define WLC_OBSS_SCAN_PASSIVE_TOTAL_PER_CHANNEL_DEFAULT 200 /* unit TU */ #define WLC_OBSS_SCAN_PASSIVE_TOTAL_PER_CHANNEL_MIN 200 /* unit TU */ #define WLC_OBSS_SCAN_PASSIVE_TOTAL_PER_CHANNEL_MAX 10000 /* unit TU */ #define WLC_OBSS_SCAN_ACTIVE_TOTAL_PER_CHANNEL_DEFAULT 20 /* unit TU */ #define WLC_OBSS_SCAN_ACTIVE_TOTAL_PER_CHANNEL_MIN 20 /* unit TU */ #define WLC_OBSS_SCAN_ACTIVE_TOTAL_PER_CHANNEL_MAX 10000 /* unit TU */ #define WLC_OBSS_SCAN_ACTIVITY_THRESHOLD_DEFAULT 25 /* unit percent */ #define WLC_OBSS_SCAN_ACTIVITY_THRESHOLD_MIN 0 /* unit percent */ #define WLC_OBSS_SCAN_ACTIVITY_THRESHOLD_MAX 100 /* unit percent */ #define WL_MIN_NUM_OBSS_SCAN_ARG 7 /* minimum number of arguments required for OBSS Scan */ #define WL_COEX_INFO_MASK 0x07 #define WL_COEX_INFO_REQ 0x01 #define WL_COEX_40MHZ_INTOLERANT 0x02 #define WL_COEX_WIDTH20 0x04 #define WLC_RSSI_INVALID 0 /* invalid RSSI value */ #define MAX_RSSI_LEVELS 8 #define MAX_ARGSTR_LEN 18 /* At least big enough for storing ETHER_ADDR_STR_LEN */ /* log modules (bitmap) */ #define LOG_MODULE_COMMON 0x0001 #define LOG_MODULE_ASSOC 0x0002 #define LOG_MODULE_EVENT 0x0004 #define LOG_MODULE_MAX 3 /* Update when adding module */ /* log levels */ #define WL_LOG_LEVEL_DISABLE 0 #define WL_LOG_LEVEL_ERR 1 #define WL_LOG_LEVEL_WARN 2 #define WL_LOG_LEVEL_INFO 3 #define WL_LOG_LEVEL_MAX WL_LOG_LEVEL_INFO /* Update when adding level */ /* flag */ #define LOG_FLAG_EVENT 1 /* log arg_type */ #define LOG_ARGTYPE_NULL 0 #define LOG_ARGTYPE_STR 1 /* %s */ #define LOG_ARGTYPE_INT 2 /* %d */ #define LOG_ARGTYPE_INT_STR 3 /* %d...%s */ #define LOG_ARGTYPE_STR_INT 4 /* %s...%d */ /* 802.11 Mgmt Packet flags */ #define VNDR_IE_BEACON_FLAG 0x1 #define VNDR_IE_PRBRSP_FLAG 0x2 #define VNDR_IE_ASSOCRSP_FLAG 0x4 #define VNDR_IE_AUTHRSP_FLAG 0x8 #define VNDR_IE_PRBREQ_FLAG 0x10 #define VNDR_IE_ASSOCREQ_FLAG 0x20 #define VNDR_IE_IWAPID_FLAG 0x40 /* vendor IE in IW advertisement protocol ID field */ #define VNDR_IE_AUTHREQ_FLAG 0x80 #define VNDR_IE_CUSTOM_FLAG 0x100 /* allow custom IE id */ #define VNDR_IE_DISASSOC_FLAG 0x200 #if defined(WLP2P) /* P2P Action Frames flags (spec ordered) */ #define VNDR_IE_GONREQ_FLAG 0x001000 #define VNDR_IE_GONRSP_FLAG 0x002000 #define VNDR_IE_GONCFM_FLAG 0x004000 #define VNDR_IE_INVREQ_FLAG 0x008000 #define VNDR_IE_INVRSP_FLAG 0x010000 #define VNDR_IE_DISREQ_FLAG 0x020000 #define VNDR_IE_DISRSP_FLAG 0x040000 #define VNDR_IE_PRDREQ_FLAG 0x080000 #define VNDR_IE_PRDRSP_FLAG 0x100000 #define VNDR_IE_P2PAF_SHIFT 12 #endif /* WLP2P */ /* channel interference measurement (chanim) related defines */ /* chanim mode */ #define CHANIM_DISABLE 0 /* disabled */ #define CHANIM_DETECT 1 /* detection only */ #define CHANIM_EXT 2 /* external state machine */ #define CHANIM_ACT 3 /* full internal state machine, detect + act */ #define CHANIM_MODE_MAX 4 /* define for apcs reason code */ #define APCS_INIT 0 #define APCS_IOCTL 1 #define APCS_CHANIM 2 #define APCS_CSTIMER 3 #define APCS_TXDLY 5 #define APCS_NONACSD 6 #define APCS_DFS_REENTRY 7 #define APCS_TXFAIL 8 #define APCS_MAX 9 /* number of ACS record entries */ #define CHANIM_ACS_RECORD 10 /* CHANIM */ #define CCASTATS_TXDUR 0 #define CCASTATS_INBSS 1 #define CCASTATS_OBSS 2 #define CCASTATS_NOCTG 3 #define CCASTATS_NOPKT 4 #define CCASTATS_DOZE 5 #define CCASTATS_TXOP 6 #define CCASTATS_GDTXDUR 7 #define CCASTATS_BDTXDUR 8 /* FIXME: CCASTATS_MAX is 9 for existing chips and 10 for new ones. * This is to avoid rom invalidation of existing chips. */ #ifndef WLCHANIM_V2 #define CCASTATS_MAX 9 #else /* WLCHANIM_V2 */ #define CCASTATS_MYRX 9 #define CCASTATS_MAX 10 #endif /* WLCHANIM_V2 */ #define WL_CHANIM_COUNT_ALL 0xff #define WL_CHANIM_COUNT_ONE 0x1 /* Module id: to know which module has sent the stats */ #define SC_CHANIM_ID_NULL 0u #define SC_CHANIM_ID_SCAN 1u /* Module Id of scan, used to report scqs */ #define SC_CHANIM_ID_STA 2u /* Module Id of STA, used tp report scqs */ /* ap tpc modes */ #define AP_TPC_OFF 0 #define AP_TPC_BSS_PWR 1 /* BSS power control */ #define AP_TPC_AP_PWR 2 /* AP power control */ #define AP_TPC_AP_BSS_PWR 3 /* Both AP and BSS power control */ #define AP_TPC_MAX_LINK_MARGIN 127 /* ap tpc modes */ #define AP_TPC_OFF 0 #define AP_TPC_BSS_PWR 1 /* BSS power control */ #define AP_TPC_AP_PWR 2 /* AP power control */ #define AP_TPC_AP_BSS_PWR 3 /* Both AP and BSS power control */ #define AP_TPC_MAX_LINK_MARGIN 127 /* tpc option bits */ #define TPC_OPT_NO_11DH_TXPWR 1 /* Do not adopt 11d+11h AP power constraints when * autocountry is 0 */ /* state */ #define WL_P2P_DISC_ST_SCAN 0 #define WL_P2P_DISC_ST_LISTEN 1 #define WL_P2P_DISC_ST_SEARCH 2 /* i/f type */ #define WL_P2P_IF_CLIENT 0 #define WL_P2P_IF_GO 1 #define WL_P2P_IF_DYNBCN_GO 2 #define WL_P2P_IF_DEV 3 /* p2p GO configuration */ #define WL_P2P_ENABLE_CONF 1 /* configure */ #define WL_P2P_DISABLE_CONF 0 /* un-configure */ /* count */ #define WL_P2P_SCHED_RSVD 0 #define WL_P2P_SCHED_REPEAT 255 /* anything > 255 will be treated as 255 */ #define WL_P2P_SCHED_FIXED_LEN 3 /* schedule type */ #define WL_P2P_SCHED_TYPE_ABS 0 /* Scheduled Absence */ #define WL_P2P_SCHED_TYPE_REQ_ABS 1 /* Requested Absence */ /* at some point we may need bitvec here (combination of actions) */ /* schedule action during absence periods (for WL_P2P_SCHED_ABS type) */ #define WL_P2P_SCHED_ACTION_NONE 0 /* no action */ #define WL_P2P_SCHED_ACTION_DOZE 1 /* doze */ /* schedule option - WL_P2P_SCHED_TYPE_REQ_ABS */ #define WL_P2P_SCHED_ACTION_GOOFF 2 /* turn off GO beacon/prbrsp functions */ /* schedule option - WL_P2P_SCHED_TYPE_XXX */ #define WL_P2P_SCHED_ACTION_RESET 255 /* reset */ /* at some point we may need bitvec here (combination of options) */ /* schedule option - WL_P2P_SCHED_TYPE_ABS */ #define WL_P2P_SCHED_OPTION_NORMAL 0 /* normal start/interval/duration/count */ #define WL_P2P_SCHED_OPTION_BCNPCT 1 /* percentage of beacon interval */ /* schedule option - WL_P2P_SCHED_TYPE_REQ_ABS */ #define WL_P2P_SCHED_OPTION_TSFOFS 2 /* normal start/internal/duration/count with * start being an offset of the 'current' TSF */ /* feature flags */ #define WL_P2P_FEAT_GO_CSA (1 << 0) /* GO moves with the STA using CSA method */ #define WL_P2P_FEAT_GO_NOLEGACY (1 << 1) /* GO does not probe respond to non-p2p probe * requests */ #define WL_P2P_FEAT_RESTRICT_DEV_RESP (1 << 2) /* Restrict p2p dev interface from responding */ /* n-mode support capability */ /* 2x2 includes both 1x1 & 2x2 devices * reserved #define 2 for future when we want to separate 1x1 & 2x2 and * control it independently */ #define WL_11N_2x2 1 #define WL_11N_3x3 3 #define WL_11N_4x4 4 /* define 11n feature disable flags */ #define WLFEATURE_DISABLE_11N 0x00000001 #define WLFEATURE_DISABLE_11N_STBC_TX 0x00000002 #define WLFEATURE_DISABLE_11N_STBC_RX 0x00000004 #define WLFEATURE_DISABLE_11N_SGI_TX 0x00000008 #define WLFEATURE_DISABLE_11N_SGI_RX 0x00000010 #define WLFEATURE_DISABLE_11N_AMPDU_TX 0x00000020 #define WLFEATURE_DISABLE_11N_AMPDU_RX 0x00000040 #define WLFEATURE_DISABLE_11N_GF 0x00000080 /* op code in nat_cfg */ #define NAT_OP_ENABLE 1 /* enable NAT on given interface */ #define NAT_OP_DISABLE 2 /* disable NAT on given interface */ #define NAT_OP_DISABLE_ALL 3 /* disable NAT on all interfaces */ /* NAT state */ #define NAT_STATE_ENABLED 1 /* NAT is enabled */ #define NAT_STATE_DISABLED 2 /* NAT is disabled */ #define CHANNEL_5G_LOW_START 36 /* 5G low (36..48) CDD enable/disable bit mask */ #define CHANNEL_5G_MID_START 52 /* 5G mid (52..64) CDD enable/disable bit mask */ #define CHANNEL_5G_HIGH_START 100 /* 5G high (100..140) CDD enable/disable bit mask */ #define CHANNEL_5G_UPPER_START 149 /* 5G upper (149..161) CDD enable/disable bit mask */ /* D0 Coalescing */ #define IPV4_ARP_FILTER 0x0001 #define IPV4_NETBT_FILTER 0x0002 #define IPV4_LLMNR_FILTER 0x0004 #define IPV4_SSDP_FILTER 0x0008 #define IPV4_WSD_FILTER 0x0010 #define IPV6_NETBT_FILTER 0x0200 #define IPV6_LLMNR_FILTER 0x0400 #define IPV6_SSDP_FILTER 0x0800 #define IPV6_WSD_FILTER 0x1000 /* Network Offload Engine */ #define NWOE_OL_ENABLE 0x00000001 /* * Traffic management structures/defines. */ /* Traffic management bandwidth parameters */ #define TRF_MGMT_MAX_PRIORITIES 3 #define TRF_MGMT_FLAG_ADD_DSCP 0x0001 /* Add DSCP to IP TOS field */ #define TRF_MGMT_FLAG_DISABLE_SHAPING 0x0002 /* Don't shape traffic */ #define TRF_MGMT_FLAG_MANAGE_LOCAL_TRAFFIC 0x0008 /* Manage traffic over our local subnet */ #define TRF_MGMT_FLAG_FILTER_ON_MACADDR 0x0010 /* filter on MAC address */ #define TRF_MGMT_FLAG_NO_RX 0x0020 /* do not apply fiters to rx packets */ #define TRF_FILTER_MAC_ADDR 0x0001 /* L2 filter use dst mac address for filtering */ #define TRF_FILTER_IP_ADDR 0x0002 /* L3 filter use ip ddress for filtering */ #define TRF_FILTER_L4 0x0004 /* L4 filter use tcp/udp for filtering */ #define TRF_FILTER_DWM 0x0008 /* L3 filter use DSCP for filtering */ #define TRF_FILTER_FAVORED 0x0010 /* Tag the packet FAVORED */ /* WNM/NPS subfeatures mask */ #define WL_WNM_BSSTRANS 0x00000001 #define WL_WNM_PROXYARP 0x00000002 #define WL_WNM_MAXIDLE 0x00000004 #define WL_WNM_TIMBC 0x00000008 #define WL_WNM_TFS 0x00000010 #define WL_WNM_SLEEP 0x00000020 #define WL_WNM_DMS 0x00000040 #define WL_WNM_FMS 0x00000080 #define WL_WNM_NOTIF 0x00000100 #define WL_WNM_WBTEXT 0x00000200 #define WL_WNM_ESTM 0x00000400 #define WL_WNM_MAX 0x00000800 #ifdef WLWNM_BRCM #define BRCM_WNM_FEATURE_SET\ (WL_WNM_PROXYARP | \ WL_WNM_SLEEP | \ WL_WNM_FMS | \ WL_WNM_TFS | \ WL_WNM_TIMBC | \ WL_WNM_BSSTRANS | \ WL_WNM_DMS | \ WL_WNM_NOTIF | \ 0) #endif /* WLWNM_BRCM */ #ifndef ETHER_MAX_DATA #define ETHER_MAX_DATA 1500 #endif /* ETHER_MAX_DATA */ /* Different discovery modes for dpt */ #define DPT_DISCOVERY_MANUAL 0x01 /* manual discovery mode */ #define DPT_DISCOVERY_AUTO 0x02 /* auto discovery mode */ #define DPT_DISCOVERY_SCAN 0x04 /* scan-based discovery mode */ /* different path selection values */ #define DPT_PATHSEL_AUTO 0 /* auto mode for path selection */ #define DPT_PATHSEL_DIRECT 1 /* always use direct DPT path */ #define DPT_PATHSEL_APPATH 2 /* always use AP path */ /* different ops for deny list */ #define DPT_DENY_LIST_ADD 1 /* add to dpt deny list */ #define DPT_DENY_LIST_REMOVE 2 /* remove from dpt deny list */ /* different ops for manual end point */ #define DPT_MANUAL_EP_CREATE 1 /* create manual dpt endpoint */ #define DPT_MANUAL_EP_MODIFY 2 /* modify manual dpt endpoint */ #define DPT_MANUAL_EP_DELETE 3 /* delete manual dpt endpoint */ /* flags to indicate DPT status */ #define DPT_STATUS_ACTIVE 0x01 /* link active (though may be suspended) */ #define DPT_STATUS_AES 0x02 /* link secured through AES encryption */ #define DPT_STATUS_FAILED 0x04 /* DPT link failed */ #ifdef WLTDLS /* different ops for manual end point */ #define TDLS_MANUAL_EP_CREATE 1 /* create manual dpt endpoint */ #define TDLS_MANUAL_EP_MODIFY 2 /* modify manual dpt endpoint */ #define TDLS_MANUAL_EP_DELETE 3 /* delete manual dpt endpoint */ #define TDLS_MANUAL_EP_PM 4 /* put dpt endpoint in PM mode */ #define TDLS_MANUAL_EP_WAKE 5 /* wake up dpt endpoint from PM */ #define TDLS_MANUAL_EP_DISCOVERY 6 /* discover if endpoint is TDLS capable */ #define TDLS_MANUAL_EP_CHSW 7 /* channel switch */ #define TDLS_MANUAL_EP_WFD_TPQ 8 /* WiFi-Display Tunneled Probe reQuest */ /* modes */ #define TDLS_WFD_IE_TX 0 #define TDLS_WFD_IE_RX 1 #define TDLS_WFD_PROBE_IE_TX 2 #define TDLS_WFD_PROBE_IE_RX 3 #endif /* WLTDLS */ /* define for flag */ #define TSPEC_PENDING 0 /* TSPEC pending */ #define TSPEC_ACCEPTED 1 /* TSPEC accepted */ #define TSPEC_REJECTED 2 /* TSPEC rejected */ #define TSPEC_UNKNOWN 3 /* TSPEC unknown */ #define TSPEC_STATUS_MASK 7 /* TSPEC status mask */ #ifdef BCMCCX /* "wlan_reason" iovar interface */ #define WL_WLAN_ASSOC_REASON_NORMAL_NETWORK 0 /* normal WLAN network setup */ #define WL_WLAN_ASSOC_REASON_ROAM_FROM_CELLULAR_NETWORK 1 /* roam from Cellular network */ #define WL_WLAN_ASSOC_REASON_ROAM_FROM_LAN 2 /* roam from LAN */ #define WL_WLAN_ASSOC_REASON_MAX 2 /* largest value allowed */ #endif /* BCMCCX */ /* Software feature flag defines used by wlfeatureflag */ #ifdef WLAFTERBURNER #define WL_SWFL_ABBFL 0x0001 /* Allow Afterburner on systems w/o hardware BFL */ #define WL_SWFL_ABENCORE 0x0002 /* Allow AB on non-4318E chips */ #endif /* WLAFTERBURNER */ #define WL_SWFL_NOHWRADIO 0x0004 /* Disable HW Radio monitor (e.g., Cust Spec) */ #define WL_SWFL_FLOWCONTROL 0x0008 /* Enable backpressure to OS stack */ #define WL_SWFL_WLBSSSORT 0x0010 /* Per-port supports sorting of BSS */ #define WL_LIFETIME_MAX 0xFFFF /* Max value in ms */ #define CSA_BROADCAST_ACTION_FRAME 0 /* csa broadcast action frame */ #define CSA_UNICAST_ACTION_FRAME 1 /* csa unicast action frame */ /* Roaming trigger definitions for WLC_SET_ROAM_TRIGGER. * * (-100 < value < 0) value is used directly as a roaming trigger in dBm * (0 <= value) value specifies a logical roaming trigger level from * the list below * * WLC_GET_ROAM_TRIGGER always returns roaming trigger value in dBm, never * the logical roam trigger value. */ #define WLC_ROAM_TRIGGER_DEFAULT 0 /* default roaming trigger */ #define WLC_ROAM_TRIGGER_BANDWIDTH 1 /* optimize for bandwidth roaming trigger */ #define WLC_ROAM_TRIGGER_DISTANCE 2 /* optimize for distance roaming trigger */ #define WLC_ROAM_TRIGGER_AUTO 3 /* auto-detect environment */ #define WLC_ROAM_TRIGGER_MAX_VALUE 3 /* max. valid value */ #define WLC_ROAM_NEVER_ROAM_TRIGGER (-100) /* Avoid Roaming by setting a large value */ /* Preferred Network Offload (PNO, formerly PFN) defines */ #define WPA_AUTH_PFN_ANY 0xffffffff /* for PFN, match only ssid */ #define SORT_CRITERIA_BIT 0 #define AUTO_NET_SWITCH_BIT 1 #define ENABLE_BKGRD_SCAN_BIT 2 #define IMMEDIATE_SCAN_BIT 3 #define AUTO_CONNECT_BIT 4 #define ENABLE_BD_SCAN_BIT 5 #define ENABLE_ADAPTSCAN_BIT 6 #define IMMEDIATE_EVENT_BIT 8 #define SUPPRESS_SSID_BIT 9 #define ENABLE_NET_OFFLOAD_BIT 10 /* report found/lost events for SSID and BSSID networks seperately */ #define REPORT_SEPERATELY_BIT 11 #define BESTN_BSSID_ONLY_BIT 12 #define SORT_CRITERIA_MASK 0x0001 #define AUTO_NET_SWITCH_MASK 0x0002 #define ENABLE_BKGRD_SCAN_MASK 0x0004 #define IMMEDIATE_SCAN_MASK 0x0008 #define AUTO_CONNECT_MASK 0x0010 #define ENABLE_BD_SCAN_MASK 0x0020 #define ENABLE_ADAPTSCAN_MASK 0x00c0 #define IMMEDIATE_EVENT_MASK 0x0100 #define SUPPRESS_SSID_MASK 0x0200 #define ENABLE_NET_OFFLOAD_MASK 0x0400 /* report found/lost events for SSID and BSSID networks seperately */ #define REPORT_SEPERATELY_MASK 0x0800 #define BESTN_BSSID_ONLY_MASK 0x1000 #ifdef PFN_SCANRESULT_2 #define PFN_SCANRESULT_VERSION 2 #else #define PFN_SCANRESULT_VERSION 1 #endif /* PFN_SCANRESULT_2 */ #ifndef MAX_PFN_LIST_COUNT #define MAX_PFN_LIST_COUNT 64 #endif /* MAX_PFN_LIST_COUNT */ #define PFN_COMPLETE 1 #define PFN_INCOMPLETE 0 #define DEFAULT_BESTN 2 #define DEFAULT_MSCAN 0 #define DEFAULT_REPEAT 10 #define DEFAULT_EXP 2 #define PFN_PARTIAL_SCAN_BIT 0 #define PFN_PARTIAL_SCAN_MASK 1 #define WL_PFN_SUPPRESSFOUND_MASK 0x08 #define WL_PFN_SUPPRESSLOST_MASK 0x10 #define WL_PFN_SSID_A_BAND_TRIG 0x20 #define WL_PFN_SSID_BG_BAND_TRIG 0x40 #define WL_PFN_SSID_IMPRECISE_MATCH 0x80 #define WL_PFN_SSID_SAME_NETWORK 0x10000 #define WL_PFN_SUPPRESS_AGING_MASK 0x20000 #define WL_PFN_FLUSH_ALL_SSIDS 0x40000 #define WL_PFN_RSSI_MASK 0xff00 #define WL_PFN_RSSI_SHIFT 8 #define WL_PFN_REPORT_ALLNET 0 #define WL_PFN_REPORT_SSIDNET 1 #define WL_PFN_REPORT_BSSIDNET 2 #define WL_PFN_CFG_FLAGS_PROHIBITED 0x00000001 /* Accept and use prohibited channels */ #define WL_PFN_CFG_FLAGS_HISTORY_OFF 0x00000002 /* Scan history suppressed */ /* Set to avoid sending direct probe in 6G channels */ #define WL_PFN_CFG_FLAGS_NO_6GHZ_FOLLOWUP 0x00000004 #define WL_PFN_HIDDEN_BIT 2 #define PNO_SCAN_MAX_FW 508*1000 /* max time scan time in msec */ #define PNO_SCAN_MAX_FW_SEC PNO_SCAN_MAX_FW/1000 /* max time scan time in SEC */ #define PNO_SCAN_MIN_FW_SEC 10 /* min time scan time in SEC */ #define WL_PFN_HIDDEN_MASK 0x4 #define MAX_BSSID_PREF_LIST_NUM 32 #ifdef CUSTOM_SSID_WHITELIST_NUM #define MAX_SSID_WHITELIST_NUM CUSTOM_SSID_WHITELIST_NUM #else #define MAX_SSID_WHITELIST_NUM 4 #endif /* CUSTOM_SSID_WHITELIST_NUM */ #ifdef CUSTOM_BSSID_BLACKLIST_NUM #define MAX_BSSID_BLACKLIST_NUM CUSTOM_BSSID_BLACKLIST_NUM #else #define MAX_BSSID_BLACKLIST_NUM 32 #endif /* CUSTOM_BSSID_BLACKLIST_NUM */ /* TCP Checksum Offload error injection for testing */ #define TOE_ERRTEST_TX_CSUM 0x00000001 #define TOE_ERRTEST_RX_CSUM 0x00000002 #define TOE_ERRTEST_RX_CSUM2 0x00000004 /* ARP Offload feature flags for arp_ol iovar */ #define ARP_OL_AGENT 0x00000001 /* enable processing of rx ARP packets */ #define ARP_OL_SNOOP 0x00000002 /* populate using ARP pkts from host */ #define ARP_OL_HOST_AUTO_REPLY 0x00000004 /* reply to ARP request from host */ #define ARP_OL_PEER_AUTO_REPLY 0x00000008 /* reply to ARP request from peer */ #define ARP_OL_UPDATE_HOST_CACHE 0x00000010 /* forward new ARP request to host */ /* ARP Offload error injection */ #define ARP_ERRTEST_REPLY_PEER 0x1 #define ARP_ERRTEST_REPLY_HOST 0x2 #define ARP_MULTIHOMING_MAX 8 /* Maximum local host IP addresses */ #if defined(WL_PKT_FLTR_EXT) && !defined(WL_PKT_FLTR_EXT_DISABLED) #define ND_MULTIHOMING_MAX 32 /* Maximum local host IP addresses */ #else #define ND_MULTIHOMING_MAX 10 /* Maximum local host IP addresses */ #endif /* WL_PKT_FLTR_EXT && !WL_PKT_FLTR_EXT_DISABLED */ #define ND_REQUEST_MAX 5 /* Max set of offload params */ /* AOAC wake event flag */ #define WAKE_EVENT_NLO_DISCOVERY_BIT 1 #define WAKE_EVENT_AP_ASSOCIATION_LOST_BIT 2 #define WAKE_EVENT_GTK_HANDSHAKE_ERROR_BIT 4 #define WAKE_EVENT_4WAY_HANDSHAKE_REQUEST_BIT 8 #define WAKE_EVENT_NET_PACKET_BIT 0x10 #define MAX_NUM_WOL_PATTERN 22 /* LOGO requirements min 22 */ /* Packet filter operation mode */ /* True: 1; False: 0 */ #define PKT_FILTER_MODE_FORWARD_ON_MATCH 1 /* Enable and disable pkt_filter as a whole */ #define PKT_FILTER_MODE_DISABLE 2 /* Cache first matched rx pkt(be queried by host later) */ #define PKT_FILTER_MODE_PKT_CACHE_ON_MATCH 4 /* If pkt_filter is enabled and no filter is set, don't forward anything */ #define PKT_FILTER_MODE_PKT_FORWARD_OFF_DEFAULT 8 #ifdef DONGLEOVERLAYS #define OVERLAY_IDX_MASK 0x000000ff #define OVERLAY_IDX_SHIFT 0 #define OVERLAY_FLAGS_MASK 0xffffff00 #define OVERLAY_FLAGS_SHIFT 8 /* overlay written to device memory immediately after loading the base image */ #define OVERLAY_FLAG_POSTLOAD 0x100 /* defer overlay download until the device responds w/WLC_E_OVL_DOWNLOAD event */ #define OVERLAY_FLAG_DEFER_DL 0x200 /* overlay downloaded prior to the host going to sleep */ #define OVERLAY_FLAG_PRESLEEP 0x400 #define OVERLAY_DOWNLOAD_CHUNKSIZE 1024 #endif /* DONGLEOVERLAYS */ /* reuse two number in the sc/rc space */ #define SMFS_CODE_MALFORMED 0xFFFE #define SMFS_CODE_IGNORED 0xFFFD /* RFAWARE def */ #define BCM_ACTION_RFAWARE 0x77 #define BCM_ACTION_RFAWARE_DCS 0x01 /* DCS reason code define */ #define BCM_DCS_IOVAR 0x1 #define BCM_DCS_UNKNOWN 0xFF #ifdef EXT_STA #define IHV_OID_BCM 0x00181000 /* based on BRCM_OUI value */ /* --------------------------------------------------------------------------- * Event codes * --------------------------------------------------------------------------- */ #ifdef BCMCCX #define IHV_CCX_EVENT_STATUS_INDICATION 0x00000001L /* from driver */ #define IHV_CCX_EVENT_PACKET_RECEIVED 0x00000002L /* from driver */ #define IHV_CCX_EVENT_PACKET_TRANSMITTED 0x00000003L /* from driver */ #define IHV_CCX_EVENT_OID 0x00000004L /* to driver */ #define IHV_CCX_EVENT_OK_TO_ASSOCIATE 0x00000005L /* to driver */ #define IHV_CCX_EVENT_SEND_PACKET 0x00000006L /* to driver */ #endif /* BCMCCX */ #define IHV_DRIVER_EVENT_GEN_INDICATION 0x00000011L /* from driver */ #endif /* EXT_STA */ #ifdef PROP_TXSTATUS /* Bit definitions for tlv iovar */ /* * enable RSSI signals: * WLFC_CTL_TYPE_RSSI */ #define WLFC_FLAGS_RSSI_SIGNALS 0x0001 /* enable (if/mac_open, if/mac_close,, mac_add, mac_del) signals: * * WLFC_CTL_TYPE_MAC_OPEN * WLFC_CTL_TYPE_MAC_CLOSE * * WLFC_CTL_TYPE_INTERFACE_OPEN * WLFC_CTL_TYPE_INTERFACE_CLOSE * * WLFC_CTL_TYPE_MACDESC_ADD * WLFC_CTL_TYPE_MACDESC_DEL * */ #define WLFC_FLAGS_XONXOFF_SIGNALS 0x0002 /* enable (status, fifo_credit, mac_credit) signals * WLFC_CTL_TYPE_MAC_REQUEST_CREDIT * WLFC_CTL_TYPE_TXSTATUS * WLFC_CTL_TYPE_FIFO_CREDITBACK */ #define WLFC_FLAGS_CREDIT_STATUS_SIGNALS 0x0004 #define WLFC_FLAGS_HOST_PROPTXSTATUS_ACTIVE 0x0008 #define WLFC_FLAGS_PSQ_GENERATIONFSM_ENABLE 0x0010 #define WLFC_FLAGS_PSQ_ZERO_BUFFER_ENABLE 0x0020 #define WLFC_FLAGS_HOST_RXRERODER_ACTIVE 0x0040 #define WLFC_FLAGS_PKT_STAMP_SIGNALS 0x0080 #endif /* PROP_TXSTATUS */ #define WL_TIMBC_STATUS_AP_UNKNOWN 255 /* AP status for internal use only */ #define WL_DFRTS_LOGIC_OFF 0 /* Feature is disabled */ #define WL_DFRTS_LOGIC_OR 1 /* OR all non-zero threshold conditions */ #define WL_DFRTS_LOGIC_AND 2 /* AND all non-zero threshold conditions */ /* Definitions for Reliable Multicast */ #define WL_RELMCAST_MAX_CLIENT 32 #define WL_RELMCAST_FLAG_INBLACKLIST 1 #define WL_RELMCAST_FLAG_ACTIVEACKER 2 #define WL_RELMCAST_FLAG_RELMCAST 4 /* structures for proximity detection device role */ #define WL_PROXD_MODE_DISABLE 0 #define WL_PROXD_MODE_NEUTRAL 1 #define WL_PROXD_MODE_INITIATOR 2 #define WL_PROXD_MODE_TARGET 3 #define WL_PROXD_RANDOM_WAKEUP 0x8000 #ifdef NET_DETECT #define NET_DETECT_MAX_WAKE_DATA_SIZE 2048 #define NET_DETECT_MAX_PROFILES 16 #define NET_DETECT_MAX_CHANNELS 50 #endif /* NET_DETECT */ /* Bit masks for radio disabled status - returned by WL_GET_RADIO */ #define WL_RADIO_SW_DISABLE (1<<0) #define WL_RADIO_HW_DISABLE (1<<1) #define WL_RADIO_MPC_DISABLE (1<<2) #define WL_RADIO_COUNTRY_DISABLE (1<<3) /* some countries don't support any channel */ #define WL_RADIO_PERCORE_DISABLE (1<<4) /* Radio diable per core for DVT */ #define WL_RADIO_TSYNC_PWRSAVE_DISABLE (1<<5) /* Disable Radio in tsync mode for power saving */ #define WL_SPURAVOID_OFF 0 #define WL_SPURAVOID_ON1 1 #define WL_SPURAVOID_ON2 2 #define WL_4335_SPURAVOID_ON1 1 #define WL_4335_SPURAVOID_ON2 2 #define WL_4335_SPURAVOID_ON3 3 #define WL_4335_SPURAVOID_ON4 4 #define WL_4335_SPURAVOID_ON5 5 #define WL_4335_SPURAVOID_ON6 6 #define WL_4335_SPURAVOID_ON7 7 #define WL_4335_SPURAVOID_ON8 8 #define WL_4335_SPURAVOID_ON9 9 /* Override bit for WLC_SET_TXPWR. if set, ignore other level limits */ #define WL_TXPWR_OVERRIDE (1U<<31) #define WL_TXPWR_2G (1U<<30) #define WL_TXPWR_5G (1U<<29) #define WL_TXPWR_NEG (1U<<28) #define WL_TXPWR_MASK (~(0x7<<29)) #define WL_TXPWR_CORE_MAX (3) #define WL_TXPWR_CORE0_MASK (0x000000FF) #define WL_TXPWR_CORE0_SHIFT (0) #define WL_TXPWR_CORE1_MASK (0x0000FF00) #define WL_TXPWR_CORE1_SHIFT (8) #define WL_TXPWR_CORE2_MASK (0x00FF0000) #define WL_TXPWR_CORE2_SHIFT (16) /* phy types (returned by WLC_GET_PHYTPE) */ #define WLC_PHY_TYPE_A 0 #define WLC_PHY_TYPE_B 1 #define WLC_PHY_TYPE_G 2 #define WLC_PHY_TYPE_N 4 #define WLC_PHY_TYPE_LP 5 #define WLC_PHY_TYPE_SSN 6 #define WLC_PHY_TYPE_HT 7 #define WLC_PHY_TYPE_LCN 8 #define WLC_PHY_TYPE_LCN40 10 #define WLC_PHY_TYPE_AC 11 #define WLC_PHY_TYPE_LCN20 12 #define WLC_PHY_TYPE_NULL 0xf /* Values for PM */ #define PM_OFF 0 #define PM_MAX 1 #define PM_FAST 2 #define PM_FORCE_OFF 3 /* use this bit to force PM off even bt is active */ #define WL_WME_CNT_VERSION 1 /* current version of wl_wme_cnt_t */ /* fbt_cap: FBT assoc / reassoc modes. */ #define WLC_FBT_CAP_DRV_4WAY_AND_REASSOC 1 /* Driver 4-way handshake & reassoc (WLFBT). */ /* monitor_promisc_level bits */ #define WL_MONPROMISC_PROMISC 0x0001 #define WL_MONPROMISC_CTRL 0x0002 #define WL_MONPROMISC_FCS 0x0004 /* TCP Checksum Offload defines */ #define TOE_TX_CSUM_OL 0x00000001 #define TOE_RX_CSUM_OL 0x00000002 /* Wi-Fi Display Services (WFDS) */ #define WL_P2P_SOCIAL_CHANNELS_MAX WL_NUMCHANNELS #define MAX_WFDS_SEEK_SVC 4 /* Max # of wfds services to seek */ #define MAX_WFDS_ADVERT_SVC 4 /* Max # of wfds services to advertise */ #define MAX_WFDS_SVC_NAME_LEN 200 /* maximum service_name length */ #define MAX_WFDS_ADV_SVC_INFO_LEN 65000 /* maximum adv service_info length */ #define P2P_WFDS_HASH_LEN 6 /* Length of a WFDS service hash */ #define MAX_WFDS_SEEK_SVC_INFO_LEN 255 /* maximum seek service_info req length */ #define MAX_WFDS_SEEK_SVC_NAME_LEN 200 /* maximum service_name length */ /* ap_isolate bitmaps */ #define AP_ISOLATE_DISABLED 0x0 #define AP_ISOLATE_SENDUP_ALL 0x01 #define AP_ISOLATE_SENDUP_MCAST 0x02 /* Type values for the wl_pwrstats_t data field */ #define WL_PWRSTATS_TYPE_PHY 0 /**< struct wl_pwr_phy_stats */ #define WL_PWRSTATS_TYPE_SCAN 1 /**< struct wl_pwr_scan_stats */ #define WL_PWRSTATS_TYPE_USB_HSIC 2 /**< struct wl_pwr_usb_hsic_stats */ #define WL_PWRSTATS_TYPE_PM_AWAKE1 3 /**< struct wl_pwr_pm_awake_stats_v1 */ #define WL_PWRSTATS_TYPE_CONNECTION 4 /* struct wl_pwr_connect_stats; assoc and key-exch time */ #define WL_PWRSTATS_TYPE_PCIE 6 /**< struct wl_pwr_pcie_stats */ #define WL_PWRSTATS_TYPE_PM_AWAKE2 7 /**< struct wl_pwr_pm_awake_stats_v2 */ #define WL_PWRSTATS_TYPE_SDIO 8 /* struct wl_pwr_sdio_stats */ #define WL_PWRSTATS_TYPE_MIMO_PS_METRICS 9 /* struct wl_mimo_meas_metrics_t */ #define WL_PWRSTATS_TYPE_SLICE_INDEX 10 /* slice index for which this report is meant for */ #define WL_PWRSTATS_TYPE_TSYNC 11 /**< struct wl_pwr_tsync_stats */ #define WL_PWRSTATS_TYPE_OPS_STATS 12 /* struct wl_pwr_ops_stats_t */ #define WL_PWRSTATS_TYPE_BCNTRIM_STATS 13 /* struct wl_pwr_bcntrim_stats_t */ #define WL_PWRSTATS_TYPE_SLICE_INDEX_BAND_INFO 14 /* wl_pwr_slice_index_band_t */ #define WL_PWRSTATS_TYPE_PSBW_STATS 15 /* struct wl_pwr_psbw_stats_t */ #define WL_PWRSTATS_TYPE_PM_ACCUMUL 16 /* struct wl_pwr_pm_accum_stats_v1_t */ #define WL_PWRSTATS_TYPE_SCAN_6E 17 /* struct wl_pwr_scan_6E_stats_v1 */ #define WL_PWRSTATS_TYPE_SCAN_EXT 18 /**< struct wl_pwr_scan_stats_v1 */ /* IOV AWD DATA */ #define AWD_DATA_JOIN_INFO 0 #define AWD_DATA_VERSION_V1 1 /* IOV ETD DATA */ #define ETD_DATA_JOIN_INFO 0 #define ETD_DATA_VERSION_V1 1 /* CTMODE DBG */ /* input param: [31:16] => MPDU_THRESHOLD * [15:03] => RESERVED * [02] => enable UFP * [01] => enable UFC * [00] => enalbe CTMODE */ #define CTMODE_DBG_CTMODE_EN (0x1u) #define CTMODE_DBG_UFC_EN (0x2u) #define CTMODE_DBG_UFP_EN (0x4u) #define CTMODE_DBG_MPDU_THRESHOLD_SHIFT (7u) #define CTMODE_DBG_MPDU_THRESHOLD_MASK ((0x1FFu) << CTMODE_DBG_MPDU_THRESHOLD_SHIFT) #define CTMODE_DBG_BYTES_THRESHOLD_SHIFT (16u) #define CTMODE_DBG_BYTES_THRESHOLD_MASK ((0xFFFu) << CTMODE_DBG_BYTES_THRESHOLD_SHIFT) /* ====== SC use case configs ========= */ /* SC user/use case request */ #define WL_SC_REQ_SCAN 0u /* user scan */ #define WL_SC_REQ_CNX 1u /* associated idle */ #define WL_SC_REQ_NAN 2u /* NAN synchronization and discovery offload */ /* === Per use case configuration === */ /* scan cfgs */ #define SC_SCAN_CFG_PASSIVE_MASK 0x01u /* Enable passive scan on sc */ #define SC_SCAN_CFG_PASSIVE_SHIFT 0u #define SC_SCAN_CFG_LP_SCAN_MASK 0x02u /* Enable low prio scan on sc */ #define SC_SCAN_CFG_LP_SCAN_SHIFT 1u #define SC_SCAN_CFG_REG_SCAN_MASK 0x04u /* Enable split scan using sc */ #define SC_SCAN_CFG_REG_SCAN_SHIFT 2u #define SC_SCAN_CFG_FULL_SCAN_MASK 0x08u /* Enable full scan on sc */ #define SC_SCAN_CFG_FULL_SCAN_SHIFT 3u /* Add get and set macros for each of the configs? */ /* === Place holder for cnx and nan cfgs === */ /* Timeout checks to disable. Bits in mask, returned by hnd_get_dbg_disable_to_mask() */ /* Disables H2D DMA stall health check */ #define DBG_DISABLE_PCIE_H2D_DMA_TO_MASK 0x00000001 /* Disables D2H DMA stall health check */ #define DBG_DISABLE_PCIE_D2H_DMA_TO_MASK 0x00000002 /* Disables IOCTL timeout health check */ #define DBG_DISABLE_PCIE_IOCTL_TO_MASK 0x00000004 /* Disables flowring timeout health check */ #define DBG_DISABLE_PCIE_FLOWRING_TO_MASK 0x00000008 /* Disables rxpost timeout health check */ #define DBG_DISABLE_PCIE_RXPOST_TO_MASK 0x00000010 /* Disables D3ACK timeout health check */ #define DBG_DISABLE_PCIE_D3ACK_TO_MASK 0x00000020 /* Disables DS ACK timeout health check */ #define DBG_DISABLE_PCIE_DSACK_TO_MASK 0x00000040 /* Disables host wake assert timeout health check */ #define DBG_DISABLE_PCIE_HOST_WAKE_TO_MASK 0x00000080 /* Disables deep sleep wake timeout health check */ #define DBG_DISABLE_DS_NO_SLEEP_TO_MASK 0x00000100 /* Disables RX DMA stall health check */ #define DBG_DISABLE_RX_STALL_TO_MASK 0x00000200 /* Disables TX DMA stall health check */ #define DBG_DISABLE_TX_STALL_TO_MASK 0x00000400 #endif /* wlioctl_defs_h */