Merge "Merge android13-5.10-2023-03 into android13-gs-pixel-5.10-udc" into android13-gs-pixel-5.10-udc

8 files changed, 293 insertions, 90 deletions

diff --git a/drivers/hid/hid-bigbenff.c b/drivers/hid/hid-bigbenff.c
index e8c5e3ac9fff..a02cb517b4c4 100644
--- a/drivers/hid/hid-bigbenff.c
+++ b/drivers/hid/hid-bigbenff.c
@@ -174,6 +174,7 @@ static __u8 pid0902_rdesc_fixed[] = {
 struct bigben_device {
 	struct hid_device *hid;
 	struct hid_report *report;
+	spinlock_t lock;
 	bool removed;
 	u8 led_state;         /* LED1 = 1 .. LED4 = 8 */
 	u8 right_motor_on;    /* right motor off/on 0/1 */
@@ -184,18 +185,39 @@ struct bigben_device {
 	struct work_struct worker;
 };
 
+static inline void bigben_schedule_work(struct bigben_device *bigben)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&bigben->lock, flags);
+	if (!bigben->removed)
+		schedule_work(&bigben->worker);
+	spin_unlock_irqrestore(&bigben->lock, flags);
+}
 
 static void bigben_worker(struct work_struct *work)
 {
 	struct bigben_device *bigben = container_of(work,
 		struct bigben_device, worker);
 	struct hid_field *report_field = bigben->report->field[0];
-
-	if (bigben->removed || !report_field)
+	bool do_work_led = false;
+	bool do_work_ff = false;
+	u8 *buf;
+	u32 len;
+	unsigned long flags;
+
+	buf = hid_alloc_report_buf(bigben->report, GFP_KERNEL);
+	if (!buf)
 		return;
 
+	len = hid_report_len(bigben->report);
+
+	/* LED work */
+	spin_lock_irqsave(&bigben->lock, flags);
+
 	if (bigben->work_led) {
 		bigben->work_led = false;
+		do_work_led = true;
 		report_field->value[0] = 0x01; /* 1 = led message */
 		report_field->value[1] = 0x08; /* reserved value, always 8 */
 		report_field->value[2] = bigben->led_state;
@@ -204,11 +226,22 @@ static void bigben_worker(struct work_struct *work)
 		report_field->value[5] = 0x00; /* padding */
 		report_field->value[6] = 0x00; /* padding */
 		report_field->value[7] = 0x00; /* padding */
-		hid_hw_request(bigben->hid, bigben->report, HID_REQ_SET_REPORT);
+		hid_output_report(bigben->report, buf);
 	}
 
+	spin_unlock_irqrestore(&bigben->lock, flags);
+
+	if (do_work_led) {
+		hid_hw_raw_request(bigben->hid, bigben->report->id, buf, len,
+				   bigben->report->type, HID_REQ_SET_REPORT);
+	}
+
+	/* FF work */
+	spin_lock_irqsave(&bigben->lock, flags);
+
 	if (bigben->work_ff) {
 		bigben->work_ff = false;
+		do_work_ff = true;
 		report_field->value[0] = 0x02; /* 2 = rumble effect message */
 		report_field->value[1] = 0x08; /* reserved value, always 8 */
 		report_field->value[2] = bigben->right_motor_on;
@@ -217,8 +250,17 @@ static void bigben_worker(struct work_struct *work)
 		report_field->value[5] = 0x00; /* padding */
 		report_field->value[6] = 0x00; /* padding */
 		report_field->value[7] = 0x00; /* padding */
-		hid_hw_request(bigben->hid, bigben->report, HID_REQ_SET_REPORT);
+		hid_output_report(bigben->report, buf);
 	}
+
+	spin_unlock_irqrestore(&bigben->lock, flags);
+
+	if (do_work_ff) {
+		hid_hw_raw_request(bigben->hid, bigben->report->id, buf, len,
+				   bigben->report->type, HID_REQ_SET_REPORT);
+	}
+
+	kfree(buf);
 }
 
 static int hid_bigben_play_effect(struct input_dev *dev, void *data,
@@ -228,6 +270,7 @@ static int hid_bigben_play_effect(struct input_dev *dev, void *data,
 	struct bigben_device *bigben = hid_get_drvdata(hid);
 	u8 right_motor_on;
 	u8 left_motor_force;
+	unsigned long flags;
 
 	if (!bigben) {
 		hid_err(hid, "no device data\n");
@@ -242,10 +285,13 @@ static int hid_bigben_play_effect(struct input_dev *dev, void *data,
 
 	if (right_motor_on != bigben->right_motor_on ||
 			left_motor_force != bigben->left_motor_force) {
+		spin_lock_irqsave(&bigben->lock, flags);
 		bigben->right_motor_on   = right_motor_on;
 		bigben->left_motor_force = left_motor_force;
 		bigben->work_ff = true;
-		schedule_work(&bigben->worker);
+		spin_unlock_irqrestore(&bigben->lock, flags);
+
+		bigben_schedule_work(bigben);
 	}
 
 	return 0;
@@ -259,6 +305,7 @@ static void bigben_set_led(struct led_classdev *led,
 	struct bigben_device *bigben = hid_get_drvdata(hid);
 	int n;
 	bool work;
+	unsigned long flags;
 
 	if (!bigben) {
 		hid_err(hid, "no device data\n");
@@ -267,6 +314,7 @@ static void bigben_set_led(struct led_classdev *led,
 
 	for (n = 0; n < NUM_LEDS; n++) {
 		if (led == bigben->leds[n]) {
+			spin_lock_irqsave(&bigben->lock, flags);
 			if (value == LED_OFF) {
 				work = (bigben->led_state & BIT(n));
 				bigben->led_state &= ~BIT(n);
@@ -274,10 +322,11 @@ static void bigben_set_led(struct led_classdev *led,
 				work = !(bigben->led_state & BIT(n));
 				bigben->led_state |= BIT(n);
 			}
+			spin_unlock_irqrestore(&bigben->lock, flags);
 
 			if (work) {
 				bigben->work_led = true;
-				schedule_work(&bigben->worker);
+				bigben_schedule_work(bigben);
 			}
 			return;
 		}
@@ -307,8 +356,12 @@ static enum led_brightness bigben_get_led(struct led_classdev *led)
 static void bigben_remove(struct hid_device *hid)
 {
 	struct bigben_device *bigben = hid_get_drvdata(hid);
+	unsigned long flags;
 
+	spin_lock_irqsave(&bigben->lock, flags);
 	bigben->removed = true;
+	spin_unlock_irqrestore(&bigben->lock, flags);
+
 	cancel_work_sync(&bigben->worker);
 	hid_hw_stop(hid);
 }
@@ -318,7 +371,6 @@ static int bigben_probe(struct hid_device *hid,
 {
 	struct bigben_device *bigben;
 	struct hid_input *hidinput;
-	struct list_head *report_list;
 	struct led_classdev *led;
 	char *name;
 	size_t name_sz;
@@ -343,9 +395,12 @@ static int bigben_probe(struct hid_device *hid,
 		return error;
 	}
 
-	report_list = &hid->report_enum[HID_OUTPUT_REPORT].report_list;
-	bigben->report = list_entry(report_list->next,
-		struct hid_report, list);
+	bigben->report = hid_validate_values(hid, HID_OUTPUT_REPORT, 0, 0, 8);
+	if (!bigben->report) {
+		hid_err(hid, "no output report found\n");
+		error = -ENODEV;
+		goto error_hw_stop;
+	}
 
 	if (list_empty(&hid->inputs)) {
 		hid_err(hid, "no inputs found\n");
@@ -357,6 +412,7 @@ static int bigben_probe(struct hid_device *hid,
 	set_bit(FF_RUMBLE, hidinput->input->ffbit);
 
 	INIT_WORK(&bigben->worker, bigben_worker);
+	spin_lock_init(&bigben->lock);
 
 	error = input_ff_create_memless(hidinput->input, NULL,
 		hid_bigben_play_effect);
@@ -397,7 +453,7 @@ static int bigben_probe(struct hid_device *hid,
 	bigben->left_motor_force = 0;
 	bigben->work_led = true;
 	bigben->work_ff = true;
-	schedule_work(&bigben->worker);
+	bigben_schedule_work(bigben);
 
 	hid_info(hid, "LED and force feedback support for BigBen gamepad\n");
 
diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index 0688b00e606e..98bd917a44d1 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -730,6 +730,7 @@ struct dwc3_ep {
 #define DWC3_EP_FIRST_STREAM_PRIMED	BIT(10)
 #define DWC3_EP_PENDING_CLEAR_STALL	BIT(11)
 #define DWC3_EP_TXFIFO_RESIZED		BIT(12)
+#define DWC3_EP_DELAY_STOP             BIT(13)
 
 	/* This last one is specific to EP0 */
 #define DWC3_EP0_DIR_IN		BIT(31)
@@ -1564,6 +1565,7 @@ int dwc3_send_gadget_generic_command(struct dwc3 *dwc, unsigned int cmd,
 		u32 param);
 void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, bool interrupt);
 void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc);
+void dwc3_remove_requests(struct dwc3 *dwc, struct dwc3_ep *dep, int status);
 #else
 static inline int dwc3_gadget_init(struct dwc3 *dwc)
 { return 0; }
diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c
index 658739410992..521495fe982f 100644
--- a/drivers/usb/dwc3/ep0.c
+++ b/drivers/usb/dwc3/ep0.c
@@ -271,6 +271,7 @@ void dwc3_ep0_out_start(struct dwc3 *dwc)
 {
 	struct dwc3_ep			*dep;
 	int				ret;
+	int                             i;
 
 	complete(&dwc->ep0_in_setup);
 
@@ -279,6 +280,22 @@ void dwc3_ep0_out_start(struct dwc3 *dwc)
 			DWC3_TRBCTL_CONTROL_SETUP, false);
 	ret = dwc3_ep0_start_trans(dep);
 	WARN_ON(ret < 0);
+	for (i = 2; i < DWC3_ENDPOINTS_NUM; i++) {
+		struct dwc3_ep *dwc3_ep;
+
+		dwc3_ep = dwc->eps[i];
+		if (!dwc3_ep)
+			continue;
+
+		if (!(dwc3_ep->flags & DWC3_EP_DELAY_STOP))
+			continue;
+
+		dwc3_ep->flags &= ~DWC3_EP_DELAY_STOP;
+		if (dwc->connected)
+			dwc3_stop_active_transfer(dwc3_ep, true, true);
+		else
+			dwc3_remove_requests(dwc, dwc3_ep, -ESHUTDOWN);
+	}
 }
 
 static struct dwc3_ep *dwc3_wIndex_to_dep(struct dwc3 *dwc, __le16 wIndex_le)
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 1cd5ed0cdde3..04e673d1ecd7 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -949,12 +949,16 @@ out:
 	return 0;
 }
 
-static void dwc3_remove_requests(struct dwc3 *dwc, struct dwc3_ep *dep, int status)
+void dwc3_remove_requests(struct dwc3 *dwc, struct dwc3_ep *dep, int status)
 {
 	struct dwc3_request		*req;
 
 	dwc3_stop_active_transfer(dep, true, false);
 
+	/* If endxfer is delayed, avoid unmapping requests */
+	if (dep->flags & DWC3_EP_DELAY_STOP)
+		return;
+
 	/* - giveback all requests to gadget driver */
 	while (!list_empty(&dep->started_list)) {
 		req = next_request(&dep->started_list);
@@ -989,6 +993,7 @@ static int __dwc3_gadget_ep_disable(struct dwc3_ep *dep)
 {
 	struct dwc3		*dwc = dep->dwc;
 	u32			reg;
+	u32			mask;
 
 	trace_dwc3_gadget_ep_disable(dep);
 
@@ -1004,7 +1009,15 @@ static int __dwc3_gadget_ep_disable(struct dwc3_ep *dep)
 
 	dep->stream_capable = false;
 	dep->type = 0;
-	dep->flags &= DWC3_EP_TXFIFO_RESIZED;
+	mask = DWC3_EP_TXFIFO_RESIZED;
+	/*
+	 * dwc3_remove_requests() can exit early if DWC3 EP delayed stop is
+	 * set.  Do not clear DEP flags, so that the end transfer command will
+	 * be reattempted during the next SETUP stage.
+	 */
+	if (dep->flags & DWC3_EP_DELAY_STOP)
+		mask |= (DWC3_EP_DELAY_STOP | DWC3_EP_TRANSFER_STARTED);
+	dep->flags &= mask;
 
 	/* Clear out the ep descriptors for non-ep0 */
 	if (dep->number > 1) {
@@ -1637,6 +1650,51 @@ static int __dwc3_gadget_get_frame(struct dwc3 *dwc)
 }
 
 /**
+ * __dwc3_stop_active_transfer - stop the current active transfer
+ * @dep: isoc endpoint
+ * @force: set forcerm bit in the command
+ * @interrupt: command complete interrupt after End Transfer command
+ *
+ * When setting force, the ForceRM bit will be set. In that case
+ * the controller won't update the TRB progress on command
+ * completion. It also won't clear the HWO bit in the TRB.
+ * The command will also not complete immediately in that case.
+ */
+static int __dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, bool interrupt)
+{
+	struct dwc3_gadget_ep_cmd_params params;
+	u32 cmd;
+	int ret;
+
+	cmd = DWC3_DEPCMD_ENDTRANSFER;
+	cmd |= force ? DWC3_DEPCMD_HIPRI_FORCERM : 0;
+	cmd |= interrupt ? DWC3_DEPCMD_CMDIOC : 0;
+	cmd |= DWC3_DEPCMD_PARAM(dep->resource_index);
+	memset(&params, 0, sizeof(params));
+	ret = dwc3_send_gadget_ep_cmd(dep, cmd, &params);
+	/*
+	 * If the End Transfer command was timed out while the device is
+	 * not in SETUP phase, it's possible that an incoming Setup packet
+	 * may prevent the command's completion. Let's retry when the
+	 * ep0state returns to EP0_SETUP_PHASE.
+	 */
+	if (ret == -ETIMEDOUT && dep->dwc->ep0state != EP0_SETUP_PHASE) {
+		dep->flags |= DWC3_EP_DELAY_STOP;
+		return 0;
+	}
+	WARN_ON_ONCE(ret);
+	dep->resource_index = 0;
+
+	if (!interrupt)
+		dep->flags &= ~DWC3_EP_TRANSFER_STARTED;
+	else if (!ret)
+		dep->flags |= DWC3_EP_END_TRANSFER_PENDING;
+
+	dep->flags &= ~DWC3_EP_DELAY_STOP;
+	return ret;
+}
+
+/**
  * dwc3_gadget_start_isoc_quirk - workaround invalid frame number
  * @dep: isoc endpoint
  *
@@ -1805,21 +1863,8 @@ static int __dwc3_gadget_start_isoc(struct dwc3_ep *dep)
 	 * status, issue END_TRANSFER command and retry on the next XferNotReady
 	 * event.
 	 */
-	if (ret == -EAGAIN) {
-		struct dwc3_gadget_ep_cmd_params params;
-		u32 cmd;
-
-		cmd = DWC3_DEPCMD_ENDTRANSFER |
-			DWC3_DEPCMD_CMDIOC |
-			DWC3_DEPCMD_PARAM(dep->resource_index);
-
-		dep->resource_index = 0;
-		memset(&params, 0, sizeof(params));
-
-		ret = dwc3_send_gadget_ep_cmd(dep, cmd, &params);
-		if (!ret)
-			dep->flags |= DWC3_EP_END_TRANSFER_PENDING;
-	}
+	if (ret == -EAGAIN)
+		ret = __dwc3_stop_active_transfer(dep, false, true);
 
 	return ret;
 }
@@ -1862,6 +1907,7 @@ static int __dwc3_gadget_ep_queue(struct dwc3_ep *dep, struct dwc3_request *req)
 	 */
 	if ((dep->flags & DWC3_EP_END_TRANSFER_PENDING) ||
 	    (dep->flags & DWC3_EP_WEDGE) ||
+	    (dep->flags & DWC3_EP_DELAY_STOP) ||
 	    (dep->flags & DWC3_EP_STALL)) {
 		dep->flags |= DWC3_EP_DELAY_START;
 		return 0;
@@ -2077,7 +2123,8 @@ int __dwc3_gadget_ep_set_halt(struct dwc3_ep *dep, int value, int protocol)
 		if (!list_empty(&dep->started_list))
 			dep->flags |= DWC3_EP_DELAY_START;
 
-		if (dep->flags & DWC3_EP_END_TRANSFER_PENDING) {
+		if (dep->flags & DWC3_EP_END_TRANSFER_PENDING ||
+		    (dep->flags & DWC3_EP_DELAY_STOP)) {
 			dep->flags |= DWC3_EP_PENDING_CLEAR_STALL;
 			return 0;
 		}
@@ -3605,15 +3652,37 @@ static void dwc3_reset_gadget(struct dwc3 *dwc)
 void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
 	bool interrupt)
 {
-	struct dwc3_gadget_ep_cmd_params params;
-	u32 cmd;
-	int ret;
+	struct dwc3 *dwc = dep->dwc;
+
+	/*
+	 * Only issue End Transfer command to the control endpoint of a started
+	 * Data Phase. Typically we should only do so in error cases such as
+	 * invalid/unexpected direction as described in the control transfer
+	 * flow of the programming guide.
+	 */
+	if (dep->number <= 1 && dwc->ep0state != EP0_DATA_PHASE)
+		return;
+
+	if (interrupt && (dep->flags & DWC3_EP_DELAY_STOP))
+		return;
 
 	if (!(dep->flags & DWC3_EP_TRANSFER_STARTED) ||
 	    (dep->flags & DWC3_EP_END_TRANSFER_PENDING))
 		return;
 
 	/*
+	 * If a Setup packet is received but yet to DMA out, the controller will
+	 * not process the End Transfer command of any endpoint. Polling of its
+	 * DEPCMD.CmdAct may block setting up TRB for Setup packet, causing a
+	 * timeout. Delay issuing the End Transfer command until the Setup TRB is
+	 * prepared.
+	 */
+	if (dwc->ep0state != EP0_SETUP_PHASE && !dwc->delayed_status) {
+		dep->flags |= DWC3_EP_DELAY_STOP;
+		return;
+	}
+
+	/*
 	 * NOTICE: We are violating what the Databook says about the
 	 * EndTransfer command. Ideally we would _always_ wait for the
 	 * EndTransfer Command Completion IRQ, but that's causing too
@@ -3640,19 +3709,7 @@ void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
 	 * This mode is NOT available on the DWC_usb31 IP.
 	 */
 
-	cmd = DWC3_DEPCMD_ENDTRANSFER;
-	cmd |= force ? DWC3_DEPCMD_HIPRI_FORCERM : 0;
-	cmd |= interrupt ? DWC3_DEPCMD_CMDIOC : 0;
-	cmd |= DWC3_DEPCMD_PARAM(dep->resource_index);
-	memset(&params, 0, sizeof(params));
-	ret = dwc3_send_gadget_ep_cmd(dep, cmd, &params);
-	WARN_ON_ONCE(ret);
-	dep->resource_index = 0;
-
-	if (!interrupt)
-		dep->flags &= ~DWC3_EP_TRANSFER_STARTED;
-	else
-		dep->flags |= DWC3_EP_END_TRANSFER_PENDING;
+	__dwc3_stop_active_transfer(dep, force, interrupt);
 }
 EXPORT_SYMBOL_GPL(dwc3_stop_active_transfer);
 
diff --git a/drivers/usb/dwc3/gadget.h b/drivers/usb/dwc3/gadget.h
index 77df4b6d6c13..f763380e672e 100644
--- a/drivers/usb/dwc3/gadget.h
+++ b/drivers/usb/dwc3/gadget.h
@@ -116,6 +116,7 @@ int dwc3_gadget_ep0_queue(struct usb_ep *ep, struct usb_request *request,
 		gfp_t gfp_flags);
 int __dwc3_gadget_ep_set_halt(struct dwc3_ep *dep, int value, int protocol);
 void dwc3_ep0_send_delayed_status(struct dwc3 *dwc);
+void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force, bool interrupt);
 
 /**
  * dwc3_gadget_ep_get_transfer_index - Gets transfer index from HW
diff --git a/drivers/usb/gadget/udc/core.c b/drivers/usb/gadget/udc/core.c
index 7a00af1f9624..76afca85fd0b 100644
--- a/drivers/usb/gadget/udc/core.c
+++ b/drivers/usb/gadget/udc/core.c
@@ -47,6 +47,13 @@ static struct class *udc_class;
 static LIST_HEAD(udc_list);
 static LIST_HEAD(gadget_driver_pending_list);
 static DEFINE_MUTEX(udc_lock);
+/**
+ * protects udc->vbus, udc->started, gadget->connect, gadget->deactivate related
+ * functions. usb_gadget_connect_locked, usb_gadget_disconnect_locked,
+ * usb_udc_connect_control_locked, usb_gadget_udc_start_locked, usb_gadget_udc_stop_locked are
+ * called with this lock held.
+ */
+static DEFINE_MUTEX(connect_lock);
 
 static int udc_bind_to_driver(struct usb_udc *udc,
 		struct usb_gadget_driver *driver);
@@ -655,18 +662,9 @@ out:
 }
 EXPORT_SYMBOL_GPL(usb_gadget_vbus_disconnect);
 
-/**
- * usb_gadget_connect - software-controlled connect to USB host
- * @gadget:the peripheral being connected
- *
- * Enables the D+ (or potentially D-) pullup.  The host will start
- * enumerating this gadget when the pullup is active and a VBUS session
- * is active (the link is powered).  This pullup is always enabled unless
- * usb_gadget_disconnect() has been used to disable it.
- *
- * Returns zero on success, else negative errno.
- */
-int usb_gadget_connect(struct usb_gadget *gadget)
+/* Internal version of usb_gadget_connect needs to be called with connect_lock held. */
+static int usb_gadget_connect_locked(struct usb_gadget *gadget)
+	__must_hold(&connect_lock)
 {
 	int ret = 0;
 
@@ -675,10 +673,15 @@ int usb_gadget_connect(struct usb_gadget *gadget)
 		goto out;
 	}
 
-	if (gadget->deactivated) {
+	if (gadget->connected)
+		goto out;
+
+	if (gadget->deactivated || !gadget->udc->started) {
 		/*
 		 * If gadget is deactivated we only save new state.
 		 * Gadget will be connected automatically after activation.
+		 *
+		 * udc first needs to be started before gadget can be pulled up.
 		 */
 		gadget->connected = true;
 		goto out;
@@ -693,22 +696,32 @@ out:
 
 	return ret;
 }
-EXPORT_SYMBOL_GPL(usb_gadget_connect);
 
 /**
- * usb_gadget_disconnect - software-controlled disconnect from USB host
- * @gadget:the peripheral being disconnected
- *
- * Disables the D+ (or potentially D-) pullup, which the host may see
- * as a disconnect (when a VBUS session is active).  Not all systems
- * support software pullup controls.
+ * usb_gadget_connect - software-controlled connect to USB host
+ * @gadget:the peripheral being connected
  *
- * Following a successful disconnect, invoke the ->disconnect() callback
- * for the current gadget driver so that UDC drivers don't need to.
+ * Enables the D+ (or potentially D-) pullup.  The host will start
+ * enumerating this gadget when the pullup is active and a VBUS session
+ * is active (the link is powered).
  *
  * Returns zero on success, else negative errno.
  */
-int usb_gadget_disconnect(struct usb_gadget *gadget)
+int usb_gadget_connect(struct usb_gadget *gadget)
+{
+	int ret;
+
+	mutex_lock(&connect_lock);
+	ret = usb_gadget_connect_locked(gadget);
+	mutex_unlock(&connect_lock);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(usb_gadget_connect);
+
+/* Internal version of usb_gadget_disconnect needs to be called with connect_lock held. */
+static int usb_gadget_disconnect_locked(struct usb_gadget *gadget)
+	__must_hold(&connect_lock)
 {
 	int ret = 0;
 
@@ -720,10 +733,12 @@ int usb_gadget_disconnect(struct usb_gadget *gadget)
 	if (!gadget->connected)
 		goto out;
 
-	if (gadget->deactivated) {
+	if (gadget->deactivated || !gadget->udc->started) {
 		/*
 		 * If gadget is deactivated we only save new state.
 		 * Gadget will stay disconnected after activation.
+		 *
+		 * udc should have been started before gadget being pulled down.
 		 */
 		gadget->connected = false;
 		goto out;
@@ -741,6 +756,30 @@ out:
 
 	return ret;
 }
+
+/**
+ * usb_gadget_disconnect - software-controlled disconnect from USB host
+ * @gadget:the peripheral being disconnected
+ *
+ * Disables the D+ (or potentially D-) pullup, which the host may see
+ * as a disconnect (when a VBUS session is active).  Not all systems
+ * support software pullup controls.
+ *
+ * Following a successful disconnect, invoke the ->disconnect() callback
+ * for the current gadget driver so that UDC drivers don't need to.
+ *
+ * Returns zero on success, else negative errno.
+ */
+int usb_gadget_disconnect(struct usb_gadget *gadget)
+{
+	int ret;
+
+	mutex_lock(&connect_lock);
+	ret = usb_gadget_disconnect_locked(gadget);
+	mutex_unlock(&connect_lock);
+
+	return ret;
+}
 EXPORT_SYMBOL_GPL(usb_gadget_disconnect);
 
 /**
@@ -761,10 +800,11 @@ int usb_gadget_deactivate(struct usb_gadget *gadget)
 	if (gadget->deactivated)
 		goto out;
 
+	mutex_lock(&connect_lock);
 	if (gadget->connected) {
-		ret = usb_gadget_disconnect(gadget);
+		ret = usb_gadget_disconnect_locked(gadget);
 		if (ret)
-			goto out;
+			goto unlock;
 
 		/*
 		 * If gadget was being connected before deactivation, we want
@@ -774,6 +814,8 @@ int usb_gadget_deactivate(struct usb_gadget *gadget)
 	}
 	gadget->deactivated = true;
 
+unlock:
+	mutex_unlock(&connect_lock);
 out:
 	trace_usb_gadget_deactivate(gadget, ret);
 
@@ -797,6 +839,7 @@ int usb_gadget_activate(struct usb_gadget *gadget)
 	if (!gadget->deactivated)
 		goto out;
 
+	mutex_lock(&connect_lock);
 	gadget->deactivated = false;
 
 	/*
@@ -804,7 +847,8 @@ int usb_gadget_activate(struct usb_gadget *gadget)
 	 * while it was being deactivated, we call usb_gadget_connect().
 	 */
 	if (gadget->connected)
-		ret = usb_gadget_connect(gadget);
+		ret = usb_gadget_connect_locked(gadget);
+	mutex_unlock(&connect_lock);
 
 out:
 	trace_usb_gadget_activate(gadget, ret);
@@ -1047,12 +1091,13 @@ EXPORT_SYMBOL_GPL(usb_gadget_set_state);
 
 /* ------------------------------------------------------------------------- */
 
-static void usb_udc_connect_control(struct usb_udc *udc)
+/* Acquire connect_lock before calling this function. */
+static void usb_udc_connect_control_locked(struct usb_udc *udc) __must_hold(&connect_lock)
 {
-	if (udc->vbus)
-		usb_gadget_connect(udc->gadget);
+	if (udc->vbus && udc->started)
+		usb_gadget_connect_locked(udc->gadget);
 	else
-		usb_gadget_disconnect(udc->gadget);
+		usb_gadget_disconnect_locked(udc->gadget);
 }
 
 /**
@@ -1068,10 +1113,12 @@ void usb_udc_vbus_handler(struct usb_gadget *gadget, bool status)
 {
 	struct usb_udc *udc = gadget->udc;
 
+	mutex_lock(&connect_lock);
 	if (udc) {
 		udc->vbus = status;
-		usb_udc_connect_control(udc);
+		usb_udc_connect_control_locked(udc);
 	}
+	mutex_unlock(&connect_lock);
 }
 EXPORT_SYMBOL_GPL(usb_udc_vbus_handler);
 
@@ -1093,7 +1140,7 @@ void usb_gadget_udc_reset(struct usb_gadget *gadget,
 EXPORT_SYMBOL_GPL(usb_gadget_udc_reset);
 
 /**
- * usb_gadget_udc_start - tells usb device controller to start up
+ * usb_gadget_udc_start_locked - tells usb device controller to start up
  * @udc: The UDC to be started
  *
  * This call is issued by the UDC Class driver when it's about
@@ -1104,8 +1151,11 @@ EXPORT_SYMBOL_GPL(usb_gadget_udc_reset);
  * necessary to have it powered on.
  *
  * Returns zero on success, else negative errno.
+ *
+ * Caller should acquire connect_lock before invoking this function.
  */
-static inline int usb_gadget_udc_start(struct usb_udc *udc)
+static inline int usb_gadget_udc_start_locked(struct usb_udc *udc)
+	__must_hold(&connect_lock)
 {
 	int ret;
 
@@ -1122,7 +1172,7 @@ static inline int usb_gadget_udc_start(struct usb_udc *udc)
 }
 
 /**
- * usb_gadget_udc_stop - tells usb device controller we don't need it anymore
+ * usb_gadget_udc_stop_locked - tells usb device controller we don't need it anymore
  * @udc: The UDC to be stopped
  *
  * This call is issued by the UDC Class driver after calling
@@ -1131,8 +1181,11 @@ static inline int usb_gadget_udc_start(struct usb_udc *udc)
  * The details are implementation specific, but it can go as
  * far as powering off UDC completely and disable its data
  * line pullups.
+ *
+ * Caller should acquire connect lock before invoking this function.
  */
-static inline void usb_gadget_udc_stop(struct usb_udc *udc)
+static inline void usb_gadget_udc_stop_locked(struct usb_udc *udc)
+	__must_hold(&connect_lock)
 {
 	if (!udc->started) {
 		dev_err(&udc->dev, "UDC had already stopped\n");
@@ -1430,12 +1483,14 @@ static void usb_gadget_remove_driver(struct usb_udc *udc)
 
 	kobject_uevent(&udc->dev.kobj, KOBJ_CHANGE);
 
-	usb_gadget_disconnect(udc->gadget);
+	mutex_lock(&connect_lock);
+	usb_gadget_disconnect_locked(udc->gadget);
 	usb_gadget_disable_async_callbacks(udc);
 	if (udc->gadget->irq)
 		synchronize_irq(udc->gadget->irq);
 	udc->driver->unbind(udc->gadget);
-	usb_gadget_udc_stop(udc);
+	usb_gadget_udc_stop_locked(udc);
+	mutex_unlock(&connect_lock);
 
 	udc->driver = NULL;
 	udc->gadget->dev.driver = NULL;
@@ -1506,13 +1561,16 @@ static int udc_bind_to_driver(struct usb_udc *udc, struct usb_gadget_driver *dri
 	ret = driver->bind(udc->gadget, driver);
 	if (ret)
 		goto err1;
-	ret = usb_gadget_udc_start(udc);
+	mutex_lock(&connect_lock);
+	ret = usb_gadget_udc_start_locked(udc);
 	if (ret) {
+		mutex_unlock(&connect_lock);
 		driver->unbind(udc->gadget);
 		goto err1;
 	}
 	usb_gadget_enable_async_callbacks(udc);
-	usb_udc_connect_control(udc);
+	usb_udc_connect_control_locked(udc);
+	mutex_unlock(&connect_lock);
 
 	kobject_uevent(&udc->dev.kobj, KOBJ_CHANGE);
 	return 0;
@@ -1635,11 +1693,15 @@ static ssize_t soft_connect_store(struct device *dev,
 	}
 
 	if (sysfs_streq(buf, "connect")) {
-		usb_gadget_udc_start(udc);
-		usb_gadget_connect(udc->gadget);
+		mutex_lock(&connect_lock);
+		usb_gadget_udc_start_locked(udc);
+		usb_gadget_connect_locked(udc->gadget);
+		mutex_unlock(&connect_lock);
 	} else if (sysfs_streq(buf, "disconnect")) {
-		usb_gadget_disconnect(udc->gadget);
-		usb_gadget_udc_stop(udc);
+		mutex_lock(&connect_lock);
+		usb_gadget_disconnect_locked(udc->gadget);
+		usb_gadget_udc_stop_locked(udc);
+		mutex_unlock(&connect_lock);
 	} else {
 		dev_err(dev, "unsupported command '%s'\n", buf);
 		ret = -EINVAL;
diff --git a/fs/incfs/sysfs.c b/fs/incfs/sysfs.c
index 5c7e0fd4496c..ba91c07d2887 100644
--- a/fs/incfs/sysfs.c
+++ b/fs/incfs/sysfs.c
@@ -34,12 +34,14 @@ DECLARE_FEATURE_FLAG(corefs);
 DECLARE_FEATURE_FLAG(zstd);
 DECLARE_FEATURE_FLAG(v2);
 DECLARE_FEATURE_FLAG(bugfix_throttling);
+DECLARE_FEATURE_FLAG(bugfix_inode_eviction);
 
 static struct attribute *attributes[] = {
 	&corefs_attr.attr,
 	&zstd_attr.attr,
 	&v2_attr.attr,
 	&bugfix_throttling_attr.attr,
+	&bugfix_inode_eviction_attr.attr,
 	NULL,
 };
 
diff --git a/fs/incfs/vfs.c b/fs/incfs/vfs.c
index 83c2db970463..407345db2b3b 100644
--- a/fs/incfs/vfs.c
+++ b/fs/incfs/vfs.c
@@ -1929,6 +1929,13 @@ void incfs_kill_sb(struct super_block *sb)
 
 	pr_debug("incfs: unmount\n");
 
+	/*
+	 * We must kill the super before freeing mi, since killing the super
+	 * triggers inode eviction, which triggers the final update of the
+	 * backing file, which uses certain information for mi
+	 */
+	kill_anon_super(sb);
+
 	if (mi) {
 		if (mi->mi_backing_dir_path.dentry)
 			dinode = d_inode(mi->mi_backing_dir_path.dentry);
@@ -1944,7 +1951,6 @@ void incfs_kill_sb(struct super_block *sb)
 		incfs_free_mount_info(mi);
 		sb->s_fs_info = NULL;
 	}
-	kill_anon_super(sb);
 }
 
 static int show_options(struct seq_file *m, struct dentry *root)