ARM: dts: camera: Add support for camera hardware for Lito platforms

Add support for camera for Lito platforms as a part of new project.

Change-Id: Ica2dc26158977371a3dfc27ade1e337b54f7fc9c

1 files changed, 293 insertions, 0 deletions

diff --git a/lito-camera-sensor-mtp.dtsi b/lito-camera-sensor-mtp.dtsi
new file mode 100644
index 0000000..c3467e2
--- /dev/null
+++ b/lito-camera-sensor-mtp.dtsi
@@ -0,0 +1,293 @@
+#include <dt-bindings/clock/qcom,camcc-lito.h>
+
+&soc {
+	led_flash_rear: qcom,camera-flash@0 {
+		cell-index = <0>;
+		reg = <0x00 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+	};
+
+	led_flash_rear_aux: qcom,camera-flash@1 {
+		cell-index = <1>;
+		reg = <0x01 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator@0 {
+		cell-index = <0>;
+		reg = <0x0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_rear: qcom,eeprom@0 {
+		cell-index = <0>;
+		reg = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1104000 0 2800000>;
+		rgltr-load-current = <0 80000 105000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 13 0>,
+			<&tlmm 30 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom@1 {
+		cell-index = <1>;
+		reg = <0x1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&S8C>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1350000 0>;
+		rgltr-max-voltage = <1800000 2800000 1350000 0>;
+		rgltr-load-current = <0 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 14 0>,
+			<&tlmm 29 0>,
+			<&tlmm 71 0>;
+		gpio-reset = <1>;
+		gpio-vdig = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1",
+					"CAM_VDIG1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+		status="ok";
+	};
+
+	qcom,cam-sensor@0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x0>;
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear>;
+		led-flash-src = <&led_flash_rear>;
+		eeprom-src = <&eeprom_rear>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1104000 0>;
+		rgltr-max-voltage = <1800000 2800000 1104000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 13 0>,
+			<&tlmm 30 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x1>;
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_rear_aux>;
+		eeprom-src = <&eeprom_rear_aux>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&S8C>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1350000 0>;
+		rgltr-max-voltage = <1800000 2800000 1350000 0>;
+		rgltr-load-current = <0 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 14 0>,
+			<&tlmm 29 0>,
+			<&tlmm 71 0>;
+		gpio-reset = <1>;
+		gpio-vdig = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1",
+					"CAM_VDIG1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		status = "ok";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+	eeprom_front: qcom,eeprom@2 {
+		cell-index = <2>;
+		reg = <0x2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_front>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_front>;
+		gpios = <&tlmm 15 0>,
+			<&tlmm 32 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x02>;
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_front>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_front>;
+		gpios = <&tlmm 15 0>,
+			<&tlmm 32 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};