ARM: dts: msm: Add initial device tree for SDM660

Add initial device tree support for SDM660 target.
This is a snapshot of dtsi files as of msm-4.14
'commit <ca4ff9398e337420b> ("fbdev: msm: Use
dynamic allocation for SID variable")'.

Change-Id: Ia13a516de919c7c6c12a064f76af1ab2a8439e2d

1 files changed, 415 insertions, 0 deletions

diff --git a/qcom/sdm660-camera-sensor-qrd.dtsi b/qcom/sdm660-camera-sensor-qrd.dtsi
new file mode 100644
index 00000000..5c79eaf1
--- /dev/null
+++ b/qcom/sdm660-camera-sensor-qrd.dtsi
@@ -0,0 +1,415 @@
+&soc {
+	led_flash0: qcom,camera-flash@0 {
+		cell-index = <0>;
+		compatible = "qcom,camera-flash";
+		qcom,flash-source = <&pm660l_flash0 &pm660l_flash1>;
+		qcom,torch-source = <&pm660l_torch0 &pm660l_torch1>;
+		qcom,switch-source = <&pm660l_switch0>;
+		status = "ok";
+	};
+
+	cam_avdd_gpio_regulator:cam_avdd_fixed_regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "cam_vadd_gpio_regulator";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		enable-active-high;
+		gpio = <&tlmm 51 0>;
+		vin-supply = <&pm660l_bob>;
+	};
+
+	cam_vaf_gpio_regulator:cam_vaf_fixed_regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "cam_vaf_gpio_regulator";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		enable-active-high;
+		gpio = <&tlmm 50 0>;
+		vin-supply = <&pm660l_bob>;
+	};
+
+	cam_rear_dvdd_gpio_regulator: cam_rear_dvdd_fixed_regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "cam_rear_dvdd_gpio_regulator";
+		regulator-min-microvolt = <1350000>;
+		regulator-max-microvolt = <1350000>;
+		enable-active-high;
+		gpio = <&pm660l_gpios 4 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cam_sensor_eldo4_default>;
+		vin-supply = <&pm660_s5>;
+	};
+};
+
+&tlmm {
+	cam_sensor_rear_active: cam_sensor_rear_active {
+		/* RESET */
+		mux {
+			pins = "gpio46";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio46";
+			bias-disable; /* No PULL */
+			drive-strength = <2>; /* 2 MA */
+		};
+	};
+
+	cam_sensor_rear_suspend: cam_sensor_rear_suspend {
+		/* RESET */
+		mux {
+			pins = "gpio46";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio46";
+			bias-disable; /* No PULL */
+			drive-strength = <2>; /* 2 MA */
+		};
+	};
+
+	cam_sensor_rear2_active: cam_sensor_rear2_active {
+		/* RESET */
+		mux {
+			pins = "gpio48";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio48";
+			bias-disable; /* No PULL */
+			drive-strength = <2>; /* 2 MA */
+		};
+	};
+
+	cam_sensor_rear2_suspend: cam_sensor_rear2_suspend {
+		/* RESET */
+		mux {
+			pins = "gpio48";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio48";
+			bias-disable; /* No PULL */
+			drive-strength = <2>; /* 2 MA */
+		};
+	};
+
+	cam_sensor_front_active: cam_sensor_front_active {
+		/* RESET */
+		mux {
+			pins = "gpio47";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio47";
+			bias-disable; /* No PULL */
+			drive-strength = <2>; /* 2 MA */
+		};
+	};
+
+	cam_sensor_front_suspend: cam_sensor_front_suspend {
+		/* RESET */
+		mux {
+			pins = "gpio47";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio47";
+			bias-disable; /* No PULL */
+			drive-strength = <2>; /* 2 MA */
+		};
+	};
+};
+
+&cci {
+	actuator0: qcom,actuator@0 {
+		cell-index = <0>;
+		reg = <0x0>;
+		compatible = "qcom,actuator";
+		qcom,cci-master = <0>;
+		cam_vaf-supply = <&cam_vaf_gpio_regulator>;
+		qcom,cam-vreg-name = "cam_vaf";
+		qcom,cam-vreg-min-voltage = <2800000>;
+		qcom,cam-vreg-max-voltage = <2800000>;
+		qcom,cam-vreg-op-mode = <0>;
+	};
+
+	actuator1: qcom,actuator@1 {
+		cell-index = <1>;
+		reg = <0x1>;
+		compatible = "qcom,actuator";
+		qcom,cci-master = <1>;
+		cam_vaf-supply = <&cam_vaf_gpio_regulator>;
+		qcom,cam-vreg-name = "cam_vaf";
+		qcom,cam-vreg-min-voltage = <2800000>;
+		qcom,cam-vreg-max-voltage = <2800000>;
+		qcom,cam-vreg-op-mode = <0>;
+	};
+
+	ois0: qcom,ois@0 {
+		cell-index = <0>;
+		reg = <0x0>;
+		compatible = "qcom,ois";
+		qcom,cci-master = <0>;
+		cam_vaf-supply = <&cam_vaf_gpio_regulator>;
+		qcom,cam-vreg-name = "cam_vaf";
+		qcom,cam-vreg-min-voltage = <2800000>;
+		qcom,cam-vreg-max-voltage = <2800000>;
+		qcom,cam-vreg-op-mode = <0>;
+		status = "disabled";
+	};
+
+	eeprom0: qcom,eeprom@0 {
+		cell-index = <0>;
+		reg = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm660_l11>;
+		cam_vana-supply = <&cam_avdd_gpio_regulator>;
+		cam_vdig-supply = <&cam_rear_dvdd_gpio_regulator>;
+		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+		qcom,cam-vreg-min-voltage = <1780000 0 0>;
+		qcom,cam-vreg-max-voltage = <1950000 0 0>;
+		qcom,cam-vreg-op-mode = <105000 0 105000>;
+		qcom,gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_rear_active>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_rear_suspend>;
+		gpios = <&tlmm 32 0>,
+			<&tlmm 46 0>;
+		qcom,gpio-reset = <1>;
+		qcom,gpio-req-tbl-num = <0 1>;
+		qcom,gpio-req-tbl-flags = <1 0>;
+		qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET0";
+		qcom,sensor-position = <0>;
+		qcom,sensor-mode = <0>;
+		qcom,cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_mmss MCLK0_CLK_SRC>,
+				<&clock_mmss MMSS_CAMSS_MCLK0_CLK>;
+		clock-names = "cam_src_clk", "cam_clk";
+		qcom,clock-rates = <24000000 0>;
+	};
+
+	eeprom1: qcom,eeprom@1 {
+		cell-index = <1>;
+		reg = <0x1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm660_l11>;
+		cam_vana-supply = <&cam_avdd_gpio_regulator>;
+		cam_vdig-supply = <&cam_rear_dvdd_gpio_regulator>;
+		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+		qcom,cam-vreg-min-voltage = <1780000 0 0>;
+		qcom,cam-vreg-max-voltage = <1950000 0 0>;
+		qcom,cam-vreg-op-mode = <105000 0 0>;
+		qcom,gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_rear2_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_rear2_suspend>;
+		gpios = <&tlmm 34 0>,
+			<&tlmm 48 0>;
+		qcom,gpio-reset = <1>;
+		qcom,gpio-req-tbl-num = <0 1>;
+		qcom,gpio-req-tbl-flags = <1 0>;
+		qcom,gpio-req-tbl-label = "CAMIF_MCLK1",
+					  "CAM_RESET1";
+		qcom,sensor-position = <0>;
+		qcom,sensor-mode = <0>;
+		qcom,cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_mmss MCLK2_CLK_SRC>,
+		    <&clock_mmss MMSS_CAMSS_MCLK2_CLK>;
+		clock-names = "cam_src_clk", "cam_clk";
+		qcom,clock-rates = <24000000 0>;
+	};
+
+	eeprom2: qcom,eeprom@2 {
+		cell-index = <2>;
+		reg = <0x2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm660_l11>;
+		cam_vana-supply = <&cam_avdd_gpio_regulator>;
+		cam_vdig-supply = <&pm660_s5>;
+		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+		qcom,cam-vreg-min-voltage = <1780000 0 1352000>;
+		qcom,cam-vreg-max-voltage = <1950000 0 1352000>;
+		qcom,cam-vreg-op-mode = <105000 0 105000>;
+		qcom,gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_front_active
+				&cam_sensor_eldo3_default>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_front_suspend>;
+		gpios = <&tlmm 33 0>,
+			<&tlmm 47 0>,
+			<&pm660l_gpios 3 0>;
+		qcom,gpio-reset = <1>;
+		qcom,gpio-vdig = <2>;
+		qcom,gpio-req-tbl-num = <0 1 2>;
+		qcom,gpio-req-tbl-flags = <1 0 0>;
+		qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2",
+					"CAM_VDIG";
+		qcom,sensor-position = <1>;
+		qcom,sensor-mode = <0>;
+		qcom,cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_mmss MCLK1_CLK_SRC>,
+			<&clock_mmss MMSS_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_src_clk", "cam_clk";
+		qcom,clock-rates = <24000000 0>;
+	};
+
+	qcom,camera@0 {
+		cell-index = <0>;
+		compatible = "qcom,camera";
+		reg = <0x0>;
+		qcom,csiphy-sd-index = <0>;
+		qcom,csid-sd-index = <0>;
+		qcom,mount-angle = <270>;
+		qcom,led-flash-src = <&led_flash0>;
+		qcom,actuator-src = <&actuator0>;
+		qcom,ois-src = <&ois0>;
+		qcom,eeprom-src = <&eeprom0>;
+		cam_vio-supply = <&pm660_l11>;
+		cam_vana-supply = <&cam_avdd_gpio_regulator>;
+		cam_vdig-supply = <&cam_rear_dvdd_gpio_regulator>;
+		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+		qcom,cam-vreg-min-voltage = <1780000 0 0>;
+		qcom,cam-vreg-max-voltage = <1950000 0 0>;
+		qcom,cam-vreg-op-mode = <105000 0 0>;
+		qcom,gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				 &cam_sensor_rear_active>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				 &cam_sensor_rear_suspend>;
+		gpios = <&tlmm 32 0>,
+			<&tlmm 46 0>;
+		qcom,gpio-reset = <1>;
+		qcom,gpio-req-tbl-num = <0 1>;
+		qcom,gpio-req-tbl-flags = <1 0>;
+		qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET0";
+		qcom,sensor-position = <0>;
+		qcom,sensor-mode = <0>;
+		qcom,cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_mmss MCLK0_CLK_SRC>,
+				<&clock_mmss MMSS_CAMSS_MCLK0_CLK>;
+		clock-names = "cam_src_clk", "cam_clk";
+		qcom,clock-rates = <24000000 0>;
+	};
+
+	qcom,camera@1 {
+		cell-index = <1>;
+		compatible = "qcom,camera";
+		reg = <0x1>;
+		qcom,csiphy-sd-index = <1>;
+		qcom,csid-sd-index = <1>;
+		qcom,mount-angle = <270>;
+		qcom,led-flash-src = <&led_flash0>;
+		qcom,actuator-src = <&actuator1>;
+		qcom,eeprom-src = <&eeprom1>;
+		cam_vio-supply = <&pm660_l11>;
+		cam_vana-supply = <&cam_avdd_gpio_regulator>;
+		cam_vdig-supply = <&cam_rear_dvdd_gpio_regulator>;
+		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+		qcom,cam-vreg-min-voltage = <1780000 0 0>;
+		qcom,cam-vreg-max-voltage = <1950000 0 0>;
+		qcom,cam-vreg-op-mode = <105000 0 0>;
+		qcom,gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_rear2_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_rear2_suspend>;
+		gpios = <&tlmm 34 0>,
+			<&tlmm 48 0>;
+		qcom,gpio-reset = <1>;
+		qcom,gpio-req-tbl-num = <0 1>;
+		qcom,gpio-req-tbl-flags = <1 0>;
+		qcom,gpio-req-tbl-label = "CAMIF_MCLK1",
+					  "CAM_RESET1";
+		qcom,sensor-position = <0>;
+		qcom,sensor-mode = <0>;
+		qcom,cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_mmss MCLK2_CLK_SRC>,
+			<&clock_mmss MMSS_CAMSS_MCLK2_CLK>;
+		clock-names = "cam_src_clk", "cam_clk";
+		qcom,clock-rates = <24000000 0>;
+	};
+
+	qcom,camera@2 {
+		cell-index = <2>;
+		compatible = "qcom,camera";
+		reg = <0x02>;
+		qcom,csiphy-sd-index = <2>;
+		qcom,csid-sd-index = <2>;
+		qcom,mount-angle = <270>;
+		qcom,eeprom-src = <&eeprom2>;
+		cam_vio-supply = <&pm660_l11>;
+		cam_vana-supply = <&cam_avdd_gpio_regulator>;
+		cam_vdig-supply = <&pm660_s5>;
+		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+		qcom,cam-vreg-min-voltage = <1780000 0 1350000>;
+		qcom,cam-vreg-max-voltage = <1950000 0 1350000>;
+		qcom,cam-vreg-op-mode = <105000 0 105000>;
+		qcom,gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_front_active
+				&cam_sensor_eldo3_default>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_front_suspend>;
+		gpios = <&tlmm 33 0>,
+			<&tlmm 47 0>,
+			<&pm660l_gpios 3 0>;
+		qcom,gpio-reset = <1>;
+		qcom,gpio-vdig = <2>;
+		qcom,gpio-req-tbl-num = <0 1 2>;
+		qcom,gpio-req-tbl-flags = <1 0 0>;
+		qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2",
+					"CAM_VDIG";
+		qcom,sensor-position = <1>;
+		qcom,sensor-mode = <0>;
+		qcom,cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_mmss MCLK1_CLK_SRC>,
+			<&clock_mmss MMSS_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_src_clk", "cam_clk";
+		qcom,clock-rates = <24000000 0>;
+	};
+};
+
+&pm660l_gpios {
+	cam_sensor_eldo3 {
+		cam_sensor_eldo3_default: cam_sensor_eldo3_default {
+			pins = "gpio3";
+			function = "normal";
+			output-high;
+			bias-disable;
+		};
+	};
+	cam_sensor_eldo4 {
+		cam_sensor_eldo4_default: cam_sensor_eldo4_default {
+			pins = "gpio4";
+			function = "normal";
+			output-low;
+			bias-disable;
+		};
+	};
+};