Qualcomm Technologies, Inc. mdss-spi-panel mdss-spi-panel is a spi panel device which supports panels that are compatible with display serial interface specification. Required properties: - qcom,mdss-spi-panel-controller: Specifies the phandle for the SPI controller that this panel will be mapped to. - qcom,mdss-spi-panel-width: Specifies panel width in pixels. - qcom,mdss-spi-panel-height: Specifies panel height in pixels. - qcom,mdss-spi-bpp: Specifies the panel bits per pixels. 3 = for rgb111 8 = for rgb332 12 = for rgb444 16 = for rgb565 18 = for rgb666 24 = for rgb888 - qcom,mdss-spi-panel-destination: A string that specifies the destination display for the panel. "display_1" = DISPLAY_1 "display_2" = DISPLAY_2 - qcom,mdss-spi-on-command: A byte stream formed by multiple packets byte 0: wait number of specified ms after command transmitted byte 1: 8 bits length in network byte order byte 3 and beyond: number byte of payload - qcom,mdss-spi-off-command: A byte stream formed by multiple packets byte 0: wait number of specified ms after command transmitted byte 1: 8 bits length in network byte order byte 3 and beyond: number byte of payload Optional properties: - qcom,mdss-spi-panel-name: A string used as a descriptive name of the panel - qcom,cont-splash-enabled: Boolean used to enable continuous splash mode. If this property is specified, it is required to to specify the memory reserved for the splash screen using the qcom,memblock-reserve binding for the framebuffer device attached to the panel. - qcom,mdss-spi-h-back-porch: Horizontal back porch value in pixels. 6 = default value. - qcom,mdss-spi-h-front-porch: Horizontal front porch value in pixels. 6 = default value. - qcom,mdss-spi-h-pulse-width: Horizontal pulse width. 2 = default value. - qcom,mdss-spi-h-sync-skew: Horizontal sync skew value. 0 = default value. - qcom,mdss-spi-v-back-porch: Vertical back porch value in pixels. 6 = default value. - qcom,mdss-spi-v-front-porch: Vertical front porch value in pixels. 6 = default value. - qcom,mdss-spi-v-pulse-width: Vertical pulse width. 2 = default value. - qcom,mdss-spi-bl-pmic-control-type: A string that specifies the implementation of backlight control for this panel. "bl_ctrl_pwm" = Backlight controlled by PWM gpio. "bl_ctrl_wled" = Backlight controlled by WLED. other: Unknown backlight control. (default) - qcom,mdss-spi-bl-min-level: Specifies the min backlight level supported by the panel. 0 = default value. - qcom,mdss-spi-bl-max-level: Specifies the max backlight level supported by the panel. 255 = default value. - qcom,mdss-spi-panel-framerate: Specifies the frame rate for the panel. - qcom,mdss-spi-panel-vsync-per-te: Specifies the number of how many TE will trigger a VSYNC. - qcom,esd-check-enabled: Boolean used to enable ESD recovery feature. - qcom,mdss-spi-panel-status-check-mode:Specifies the panel status check method for ESD recovery. "send_init_command" = Regardless of panel status, direct send the panel initial code to recover panel status "reg_read" = Reads panel status register to check the panel status - qcom,mdss-spi-panel-status-reg: Unsigned 8bits integer value that specifies the value of panel status register address. - qcom,mdss-spi-panel-status-read-length: Unsigned 8bits integer value that specifies the expected read-back length of the panel register. - qcom,mdss-spi-panel-status-value: An unsigned 8bits integer araray that specifies the values of the panel status register which is used to check the panel status. The size of this array is specified by qcom,mdss-dsi-panel-status-read-length. Example: &mdss_spi_display { spi_gc9305_qvga_cmd: qcom,mdss_spi_gc9305_qvga_cmd { qcom,mdss-spi-panel-name = "gc9305 qvga command mode spi panel"; qcom,mdss-spi-panel-destination = "display_1"; qcom,mdss-spi-panel-controller = <&mdss_spi>; qcom,mdss-spi-panel-framerate = <30>; qcom,mdss-spi-panel-width = <240>; qcom,mdss-spi-panel-height = <320>; qcom,mdss-spi-h-front-porch = <79>; qcom,mdss-spi-h-back-porch = <59>; qcom,mdss-spi-h-pulse-width = <60>; qcom,mdss-spi-v-back-porch = <10>; qcom,mdss-spi-v-front-porch = <7>; qcom,mdss-spi-v-pulse-width = <2>; qcom,mdss-spi-h-left-border = <0>; qcom,mdss-spi-h-right-border = <0>; qcom,mdss-spi-v-top-border = <0>; qcom,mdss-spi-v-bottom-border = <0>; qcom,mdss-spi-bpp = <16>; qcom,mdss-spi-on-command = [00 01 FE 00 01 EF 00 02 36 48 00 02 3A 05 00 02 35 00 00 03 A4 44 44 00 03 A5 42 42 00 03 AA 88 88 00 03 E8 12 40 00 03 E3 01 10 00 02 FF 61 00 02 AC 00 00 03 A6 2A 2A 00 03 A7 2B 2B 00 03 A8 18 18 00 03 A9 2A 2A 00 02 AD 33 00 02 AF 55 00 02 AE 2B 00 05 2A 00 00 00 EF 00 05 2B 00 00 01 3F 00 01 2C 00 07 F0 02 02 00 08 0C 10 00 07 F1 01 00 00 14 1D 0E 00 07 F2 10 09 37 04 04 48 00 07 F3 10 0B 3F 05 05 4E 00 07 F4 0D 19 17 1D 1E 0F 00 07 F5 06 12 13 1A 1B 0F 78 01 11 00 01 29 00 01 2C]; qcom,mdss-spi-off-command = [20 01 28 20 01 10]; qcom,mdss-spi-bl-min-level = <1>; qcom,mdss-spi-bl-max-level = <4095>; qcom,esd-check-enabled; qcom,mdss-spi-panel-status-check-mode = "reg_read"; qcom,mdss-spi-panel-status-reg = /bits/ 8 <0x09>; qcom,mdss-spi-panel-status-read-length = <4>; qcom,mdss-spi-panel-status-value = /bits/ 8 <0x52 0x29 0x83 0x00>; }; }; mdss-spi-panel is a SPI interface panel which uses SPI protocol for data receive and send. Required properties: - compatible: Must be "qcom,mdss-spi-panel" - vdd-supply: Phandle for vdd regulator device node. - vddio-supply: Phandle for vdd-io regulator device node. - qcom,panel-supply-entries: A node that lists the elements of the supply used to power the DSI panel. There can be more than one instance of this binding, in which case the entry would be appended with the supply entry index. For a detailed description of fields in the supply entry, refer to the qcom,ctrl-supply-entries binding above. Optional properties: - pwms: Value type: Definition: The PWM device (phandle) used for controlling backlight. - qcom,platform-spi-dc-gpio: Pull down this gpio indicate current package is command, Pull up this gpio indicate current package is parameter or pixels. - qcom,platform-reset-gpio: Specifies the panel reset gpio. - qcom,platform-te-gpio: Specifies the gpio used for TE. - label: A string used to describe the controller used. -- qcom,supply-name: name of the supply (vdd/vdda/vddio) -- qcom,supply-min-voltage: minimum voltage level (uV) -- qcom,supply-max-voltage: maximum voltage level (uV) -- qcom,supply-enable-load: load drawn (uA) from enabled supply -- qcom,supply-disable-load: load drawn (uA) from disabled supply -- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on -- qcom,supply-post-on-sleep: time to sleep (ms) after turning on -- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off -- qcom,supply-post-off-sleep: time to sleep (ms) after turning off Example: mdss_spi_panel: qcom,mdss_spi_panel { compatible = "qcom,mdss-spi-panel"; label = "mdss spi panel"; vdd-supply = <&pms405_l1>; vddio-supply = <&pms405_l6>; qcom,platform-te-gpio = <&tlmm 57 0>; qcom,platform-reset-gpio = <&tlmm 42 0>; qcom,platform-spi-dc-gpio = <&tlmm 39 0>; pwms = <&pms405_l1 0 1000000>; qcom,panel-supply-entries { #address-cells = <1>; #size-cells = <0>; qcom,panel-supply-entry@0 { reg = <0>; qcom,supply-name = "vdd"; qcom,supply-min-voltage = <2850000>; qcom,supply-max-voltage = <2850000>; qcom,supply-enable-load = <100000>; qcom,supply-disable-load = <100>; }; qcom,panel-supply-entry@1 { reg = <1>; qcom,supply-name = "vddio"; qcom,supply-min-voltage = <1800000>; qcom,supply-max-voltage = <1800000>; qcom,supply-enable-load = <100000>; qcom,supply-disable-load = <100>; }; }; };