* MSM PCI express root complex

=========
Main node
=========

- compatible:
	Usage: required
	Value type: <stringlist>
	Definition: Should be "qcom,pci-msm"

- reg:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: Register ranges as listed in the reg-names property

- reg-names:
	Usage: required
	Value type: <stringlist>
	Definition: Should contain:
		- "parf"	MSM specific registers
		- "phy"		PCIe PHY registers
		- "dbi"		DesignWare PCIe registers
		- "elbi"	External local bus interface registers
		- "iatu"	Internal translation unit registers
		- "config"	PCIe device configuration space
		- "io"		PCIe device I/O registers
		- "bars"	PCIe device base address registers
		- "tcsr" (opt)	PCIe clock scheme register
		- "rumi" (opt)	PCIe RUMI register

- cell-index:
	Usage: required
	Value type: <u32>
	Definition: defines root complex ID.

- linux,pci-domain:
	Usage: required
	Value type: <u32>
	Definition: As specified in pci.txt

- #address-cells:
	Usage: required
	Value type: <u32>
	Definition: Should be 3. As specified in designware-pcie.txt

- #size-cells:
	Usage: required
	Value type: <u32>
	Definition: Should be 2. As specified in designware-pcie.txt

- ranges:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: As specified in designware-pcie.txt

- interrupt-parent:
	Usage: required
	Value type: <phandle>
	Definition: Phandle of the interrupt controller that services
		interrupts for this device

- interrupts:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: PCIe root complex related interrupts

- interrupt-names:
	Usage: required
	Value type: <stringlist>
	Definition: Should contain
		- "int_msi"
		- "int_a"
		- "int_b"
		- "int_c"
		- "int_d",
		- "int_global_int"

- #interrupt-cells:
	Usage: required
	Value type: <u32>
	Definition: Should be 1. As specified in designware-pcie.txt

- interrupt-map-mask:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: As specified in designware-pcie.txt

- interrupt-map:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: As specified in designware-pcie.txt

- msi-parent:
	Usage: required
	Value type: <phandle>
	Definition: As specified in pci-msi.txt

- <name>-gpio:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: List of phandle and GPIO specifier pairs. Should contain:
		- "perst-gpio"		PCIe reset signal line
		- "wake-gpio"		PCIe wake signal line
		- "qcom,ep-gpio" (opt)	PCIe endpoint specific signal line

- pinctrl-names:
	Usage: required
	Value type: <stringlist>
	Definition: Name of pin configuration groups. Should contain:
		- "default"
		- "sleep" (opt)

- pinctrl-<num>:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: As specified in pinctrl-bindings.txt

- <supply-name>-supply:
	Usage: required
	Value type: <phandle>
	Definition: Phandle to PCIe core and PHY power supply. Should contain:
		- "gdsc-vdd-supply"		PCIe power domain control
		- "vreg-1.8-supply"		power supply for PCIe PHY
		- "vreg-0.9-supply"		power supply for PCIe PHY
		- "vreg-cx-supply"		power supply for PCIe core
		- "vreg-3.3-supply" (opt)	power supply for PCIe endpoint

- qcom,<supply-name>-voltage-level:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: List of max/min voltage(uV) and optimal current(uA) tuple
		for power supply

- qcom,bw-scale:
	Usage: optional
	Value type: <prop-encoded-array>
	Definition: List of CX voltage corner and rate change clock frequency
		pair for each PCIe GEN speed

- qcom,msm-bus,<bus-field>:
	Usage: required
	Value type: <prop-encoded>
	Definition: As specified in msm_bus.txt

- clocks:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: List of phandle and clock specifier pairs as listed
		in clock-names property

- clock-names:
	Usage: required
	Value type: <stringlist>
	Definition: List of clock names that corresponds with listed "clocks"

- max-clock-frequency-hz:
	Usage: optional
	Value type: <u32 array>
	Definition: List of clock frequencies for each PCIe clock. Only need to
		specify the ones that needs to be changed

- resets:
	Usage: required
	Value type: <prop-encoded-array>
	Definition: List of phandle and reset specifier pairs as listed
		in reset-names property

- reset-names:
	Usage: required
	Value type: <stringlist>
	Definition: Should contain:
		- "pcie_<num>_core_reset"	Core reset
		- "pcie_<num>_phy_reset"	PHY reset
	Following resets are optional and required only if driver must perform
	link recovery post linkdown:
		- "pcie_<num>_link_down_reset"		Core linkdown reset
		- "pcie_<num>_phy_nocsr_com_phy_reset"	PHY no-csr reset

- qcom,smmu-sid-base:
	Usage: optional
	Value: <u32>
	Definition: Base SID for PCIe

- iommu-map:
	Usage: optional. Required if qcom,smmu-sid-base is defined
	Value type: <prop-encoded-array>
	Definition: As defined in pci-iommu.txt. Should contain:
		- <BDF, iommu phandle, SID, 0x1>

- qcom,target-link-speed:
	Usage: optional
	Value type: <u32>
	Definition: Override maximum GEN speed. Options:
		- 0x1	GEN 1
		- 0x2	GEN 2
		- 0x3	GEN 3

- qcom,link-check-max-count
	Usage: optional
	Value type: <u32>
	Definition: Max number of retries for link training. Delay between each
		check is 5ms

- qcom,boot-option:
	Usage: optional
	Value type: <u32>
	Definition: Controls PCIe bus driver boot sequence. Options:
		- BIT(0)	PCIe bus driver will not start enumeration
				during its probe. Clients will control when
				PCIe bus driver should do enumeration
		- BIT(1)	PCIe bus driver will not start enumeration if it
				receives a WAKE interrupt

- qcom,drv-supported:
	Usage: optional
	Value type: <bool>
	Definition: Direct resource vote (DRV) is supported. APPS PCIe
		root complex driver can hand off PCIe resources to another
		subsystem. This will allow APPS to enter lower power modes
		while keeping PCIe core, PHY, and link funtional. In addition,
		the system can enter CX power collapse once the DRV subsystem
		removes its PCIe votes.

- qcom,drv-l1ss-timeout-us:
	Usage: optional depends on qcom,drv-supported
	Value type: <u32>
	Definition: This timeout determines when DRV subsystem will put the
		link into l1ss sleep while idle in l1ss. If this is omitted,
		the default timeout is 100ms.

- qcom,use-19p2mhz-aux-clk:
	Usage: optional
	Value type: <bool>
	Definition: Set PCIe AUX clock frequency to 19.2MHz

- qcom,common-clk-en:
	Usage: optional
	Value type: <bool>
	Definition: Support common clock configuration

- qcom,clk-power-manage-en:
	Usage: optional
	Value type: <bool>
	Definition: Support clock power management

- qcom,n-fts:
	Usage: optional
	Value type: <u32>
	Definition: Number of fast training sequences sent when the link
		transitions from L0s to L0

- qcom,no-l0s-supported:
	Usage: optional
	Value type: <bool>
	Definition: L0s is not supported

- qcom,no-l1-supported:
	Usage: optional
	Value type: <bool>
	Definition: L1 is not supported

- qcom,no-l1ss-supported:
	Usage: optional
	Value type: <bool>
	Definition: L1 sub-state (L1ss) is not supported

- qcom,no-aux-clk-sync:
	Usage: optional
	Value type: <bool>
	Definition: The AUX clock is not synchronous to the Core clock to
		support L1ss

- qcom,l1-2-th-scale:
	Usage: optional
	Value type: <u32>
	Definition: Determines the multiplier for L1.2 LTR threshold value
		- 0	1ns
		- 1	32ns
		- 2	1us
		- 3	32us
		- 4	1ms
		- 5	32ms

- qcom,l1-2-th-value:
	Usage: optional
	Value type: <u32>
	Definition: L1.2 LTR threshold value to be multipled with scale to
		define L1.2 latency tolerance reporting (LTR)

- qcom,slv-addr-space-size:
	Usage: required
	Value type: <u32>
	Definition: Memory block size dedicated to PCIe root complex

- qcom,wr-halt-size:
	Usage: optional
	Value type: <u32>
	Definition: Exponent (base 2) that determines the data size(bytes) that
		PCIe core will halt for each write

- qcom,tlp-rd-size:
	Usage: optional
	Value type: <u32>
	Definition: Determines the maximum read request size(bytes). Options:
		- 0	128
		- 1	256
		- 2	512
		- 3	1K
		- 4	2K
		- 5	4K

- qcom,cpl-timeout:
	Usage: optional
	Value type: <u32>
	Definition: Determines the timeout range PCIe root complex will send
		out a completion packet if no ACK is seen for TLP. Options:
		- BIT(0)	50us to 10ms
		- BIT(1)	10ms to 250ms
		- BIT(2)	250ms to 4s
		- BIT(3)	4s to 64s

- qcom,perst-delay-us-min:
	Usage: optional
	Value type: <u32>
	Definition: Minimum allowed time(us) to sleep after asserting or
		de-asserting PERST GPI.

- qcom,perst-delay-us-max:
	Usage: optional
	Value type: <u32>
	Definition: Maximum allowed time(us) to sleep after asserting or
		de-asserting PERST GPIO

- qcom,ep-latency:
	Usage: optional
	Value type: <u32>
	Definition: The latency(ms) between when PCIe PHY is up and PERST is
		de-asserted. This guarantees the 100MHz clock is available for
		the PCIe devices

- qcom,switch-latency:
	Usage: optional
	Definition: The latency(ms) between when PCIe link is up and before
		any device over the switch is accessed

- qcom,core-preset:
	Usage: optional
	Definition: Determines how aggressive the PCIe PHY equalization is for
		Gen3 cores. The following are recommended settings:
		- short channels: 0x55555555 (default)
		- long channels: 0x77777777

- qcom,pcie-phy-ver:
	Usage: required
	Value type: <u32>
	Definition: States the PCIe PHY version

- qcom,phy-status-offset:
	Usage: required
	Value type: <u32>
	Definition: Offset from PCIe PHY base to check if PCIe PHY status

- qcom,phy-status-bit:
	Usage: required
	Value type: <u32>
	Definition: BIT to check PCIe PHY status

- qcom,phy-power-down-offset:
	Usage: required
	Value type: <u32>
	Definition: Offset from PCIe PHY base to control PHY power state

- qcom,phy-sequence:
	Usage: required
	Value type: <prop-encoded array>
	Definition: PCIe PHY initialization sequence

- qcom,config-recovery:
	Usage: optional
	Value type : <bool>
	Definition: Enable to notify the client driver for recovery when
		config space is not accessible

==============
Root port node
==============

Root port are defined as subnodes of the PCIe controller node

- reg:
	Usage: required
	Value type: <prop-encoded array>
	Definition: First cell is devfn, which is determined by pci bus
	topology. Assign the other cells 0 since they are not used

- qcom,iommu-cfg:
	Usage: optional
	Value type: <u32>
	Definition: Defines PCIe root port SMMU configuration. Options:
		- BIT(0)	Indicates if SMMU is present
		- BIT(1)	Set IOMMU attribute S1_BYPASS
		- BIT(2)	Set IOMMU attribute FAST
		- BIT(3)	Set IOMMU attribute ATOMIC
		- BIT(4)	Set IOMMU attribute FORCE COHERENT

- qcom,iommu-range:
	Usage: optional
	Value type: Array of <u64>
	Definition: Pair of values describing iova base and size to allocate

=======
Example
=======

	pcie0: qcom,pcie@1c00000 {
		compatible = "qcom,pci-msm";

		reg = <0x1c00000 0x4000>,
			<0x1c04000 0x1000>,
			<0x60000000 0xf1d>,
			<0x60000f20 0xa8>,
			<0x60001000 0x1000>,
			<0x60100000 0x100000>,
			<0x60200000 0x100000>,
			<0x60300000 0x3d00000>;
		reg-names = "parf", "phy", "dm_core", "elbi", "iatu", "conf",
				"io", "bars", "tcsr", "rumi";

		cell-index = <0>;
		device_type = "pci";
		linux,pci-domain = <0>;

		#address-cells = <3>;
		#size-cells = <2>;
		ranges = <0x01000000 0x0 0x60200000 0x60200000 0x0 0x100000>,
			<0x02000000 0x0 0x60300000 0x60300000 0x0 0x3d00000>;

		interrupt-parent = <&pcie0>;
		interrupts = <0 1 2 3 4 5>;
		interrupt-names = "int_msi", "int_a", "int_b", "int_c", "int_d",
				"int_global_int",
		#interrupt-cells = <1>;
		interrupt-map-mask = <0 0 0 0xffffffff>;
		interrupt-map = <0 0 0 0 &intc 0 141 0
				0 0 0 1 &intc 0 149 0
				0 0 0 2 &intc 0 150 0
				0 0 0 3 &intc 0 151 0
				0 0 0 4 &intc 0 152 0
				0 0 0 5 &intc 0 140 0>;
		msi-parent = <&pcie0_msi>;

		perst-gpio = <&tlmm 35 0>;
		wake-gpio = <&tlmm 37 0>;
		qcom,ep-gpio = <&tlmm 94 0>;
		pinctrl-names = "default", "sleep";
		pinctrl-0 = <&pcie0_clkreq_default
				&pcie0_perst_default
				&pcie0_wake_default>;
		pinctrl-1 = <&pcie0_clkreq_sleep
				&pcie0_perst_sleep
				&pcie0_wake_sleep>;

		gdsc-vdd-supply = <&pcie_0_gdsc>;
		vreg-1.8-supply = <&pm8150l_l3>;
		vreg-0.9-supply = <&pm8150_l5>;
		vreg-cx-supply = <&VDD_CX_LEVEL>;
		vreg-3.3-supply = <&pm8150_l1>;
		qcom,vreg-1.8-voltage-level = <1800000 1800000 1000>;
		qcom,vreg-0.9-voltage-level = <950000 950000 24000>;
		qcom,vreg-cx-voltage-level = <RPMH_REGULATOR_LEVEL_MAX
						RPMH_REGULATOR_LEVEL_NOM 0>;
		qcom,bw-scale = <RPMH_REGULATOR_LEVEL_LOW_SVS 19200000 /* Gen1 */
				<RPMH_REGULATOR_LEVEL_LOW_SVS 19200000 /* Gen2 */
				<RPMH_REGULATOR_LEVEL_NOM 100000000>; /* Gen3 */

		qcom,msm-bus,name = "pcie0";
		qcom,msm-bus,num-cases = <2>;
		qcom,msm-bus,num-paths = <1>;
		qcom,msm-bus,vectors-KBps =
				<45 512 0 0>,
				<45 512 500 800>;

		clocks = <&clock_gcc GCC_PCIE_0_PIPE_CLK>,
			<&clock_rpmh RPMH_CXO_CLK>,
			<&clock_gcc GCC_PCIE_0_AUX_CLK>,
			<&clock_gcc GCC_PCIE_0_CFG_AHB_CLK>,
			<&clock_gcc GCC_PCIE_0_MSTR_AXI_CLK>,
			<&clock_gcc GCC_PCIE_0_SLV_AXI_CLK>,
			<&clock_gcc GCC_PCIE_0_CLKREF_CLK>,
			<&clock_gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
			<&clock_gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
			<&clock_gcc GCC_PCIE0_PHY_REFGEN_CLK>,
			<&clock_gcc GCC_PCIE_PHY_AUX_CLK>;
		clock-names = "pcie_0_pipe_clk", "pcie_0_ref_clk_src",
				"pcie_0_aux_clk", "pcie_0_cfg_ahb_clk",
				"pcie_0_mstr_axi_clk", "pcie_0_slv_axi_clk",
				"pcie_0_ldo", "pcie_0_slv_q2a_axi_clk",
				"pcie_tbu_clk", "pcie_phy_refgen_clk",
				"pcie_phy_aux_clk";
		max-clock-frequency-hz = <0>, <0>, <19200000>, <0>, <0>, <0>,
					<0>, <0>, <0>, <0>, <100000000>, <0>;

		resets = <&clock_gcc GCC_PCIE_0_BCR>,
			<&clock_gcc GCC_PCIE_0_PHY_BCR>;
		reset-names = "pcie_0_core_reset",
				"pcie_0_phy_reset";

		qcom,smmu-sid-base = <0x1e00>;
		iommu-map = <0x0 &apps_smmu 0x1e00 0x1>,
			<0x100 &apps_smmu 0x1e01 0x1>;

		qcom,target-link-speed = <0x2>;
		qcom,link-check-max-count = <40> /* 200ms */
		qcom,boot-option = <0x1>;
		qcom,drv-supported;
		qcom,use-19p2mhz-aux-clk;
		qcom,common-clk-en;
		qcom,clk-power-manage-en;
		qcom,n-fts = <0x50>;
		qcom,no-l0s-supported;
		qcom,no-l1-supported;
		qcom,no-l1ss-supported;
		qcom,no-aux-clk-sync;
		qcom,slv-addr-space-size = <0x1000000>; /* 16MB */
		qcom,wr-halt-size = <0xa>; /* 1KB */
		qcom,tlp-rd-size = <0x5>; /* 4KB */
		qcom,cpl-timeout = <0x2>; /* 10ms to 250ms */
		qcom,perst-delay-us-min = <10>;
		qcom,perst-delay-us-max = <15>;
		qcom,ep-latency = <20>;
		qcom,switch-latency = <25>;

		qcom,core-preset = <0x55555555> /* short channel */
		qcom,pcie-phy-ver = <0x2101>; /* v2 version 1.01 */
		qcom,phy-status-offset = <0x814>;
		qcom,phy-status-bit = <6>;
		qcom,phy-power-down-offset = <0x840>;
		qcom,phy-sequence = <0x0840 0x03 0x0
				0x0094 0x08 0x0
				0x0154 0x34 0x0
				0x016c 0x08 0x0
				0x0058 0x0f 0x0
				0x00a4 0x42 0x0
				0x0110 0x24 0x0
				0x0800 0x00 0x0
				0x0844 0x03 0x0>;

		pcie0_rp: pcie0_rp {
			reg = <0x0 0x0 0x0 0x0 0x0>;
			qcom,iommu-cfg = <0x3> /* SMMU PRESENT. SET S1 BYPASS */
			qcom,iommu-range = <0x0 0x10000000 0x0 0x40000000>;
		};