#include "lito-mtp.dtsi"
#include <dt-bindings/iio/qcom,spmi-vadc.h>

&soc {

};

&usb_qmp_dp_phy {
	/delete-property/vdd-supply;
	vdd-supply = <&L11A>;
};

&sde_dp {
	vdda-0p9-supply = <&L11A>;
};

&sde_dsi {
	qcom,dsi-default-panel = <&dsi_sw43404_amoled_fhd_plus_cmd>;
};

&sde_dsi1 {
	status = "disabled";
};

&mdss_mdp {
	connectors = <&sde_wb &sde_dsi &sde_dp &sde_rscc>;
};

&swr0 {
	wsa883x_0221: wsa883x@02170221 {
		compatible = "qcom,wsa883x";
		reg = <0x02 0x02170221>;
		qcom,spkr-sd-n-node = <&wsa_spkr_en1>;
		qcom,bolero-handle = <&bolero>;
		cdc-vdd-1p8-supply = <&S4A>;

		qcom,cdc-vdd-1p8-voltage = <1800000 1800000>;
		qcom,cdc-vdd-1p8-current = <20000>;
		qcom,cdc-vdd-1p8-lpm-supported = <1>;
		qcom,cdc-static-supplies = "cdc-vdd-1p8";
	};

	wsa883x_0222: wsa883x@02170222 {
		compatible = "qcom,wsa883x";
		reg = <0x02 0x02170222>;
		qcom,spkr-sd-n-node = <&wsa_spkr_en2>;
		qcom,bolero-handle = <&bolero>;

		cdc-vdd-1p8-supply = <&S4A>;
		qcom,cdc-vdd-1p8-voltage = <1800000 1800000>;
		qcom,cdc-vdd-1p8-current = <20000>;
		qcom,cdc-vdd-1p8-lpm-supported = <1>;
		qcom,cdc-static-supplies = "cdc-vdd-1p8";
	};
};

&wsa881x_0211 {
	status = "disabled";
};

&wsa881x_0212 {
	status = "disabled";
};

&wsa881x_0213 {
	status = "disabled";
};

&wsa881x_0214 {
	status = "disabled";
};

&lito_snd {
	qcom,model = "lito-orchidmtp-snd-card";
	qcom,wsa-max-devs = <2>;
	qcom,wsa-devs = <&wsa883x_0221>, <&wsa883x_0222>;
	qcom,wsa-aux-dev-prefix = "SpkrLeft", "SpkrRight";
};


&pm8150_rtc {
	status = "disabled";
};

&pmk8350_adc_tm {
	status = "disabled";
};

&pmk8350_vadc {
	status = "disabled";
};

&pm7250b_qg {
	qcom,use-cp-iin-sns;
};

&pm7250b_vadc {
	smb1390_therm@e {
		qcom,scale-fn-type = <ADC_SCALE_HW_CALIB_PM5_SMB1398_TEMP>;
	};
};

&pm7250b_gpios {
	smb_stat {
		smb_stat_default: smb_stat_default {
			pins = "gpio6";
			function = "normal";
			input-enable;
			bias-pull-up;
			qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
			power-source = <0>;
		};
	};
};

&qupv3_se9_i2c {
	qcom,clk-freq-out = <100000>;
	status = "ok";
	#include "smb1398.dtsi"
};

&smb1396 {
	interrupts = <0x2 0xc5 0x0 IRQ_TYPE_LEVEL_LOW>;
	interrupt-parent = <&spmi_bus>;
	interrupt-names = "smb1396";
	pinctrl-names = "default";
	qcom,enable-toggle-stat;
	pinctrl-0 = <&smb_stat_default>;
	status = "ok";
};

&smb1396_div2_cp_master {
	io-channels = <&pm7250b_vadc ADC_AMUX_THM2>;
	qcom,parallel-input-mode = <1>; /* USBIN */
	qcom,parallel-output-mode = <2>; /* VBAT */
	qcom,min-ilim-ua = <1000000>;
	status = "ok";
};

&smb1396_slave {
	status = "ok";
};

&smb1396_div2_cp_slave {
	status = "ok";
};