#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/iio/qcom,spmi-vadc.h>
#include <dt-bindings/spmi/spmi.h>

&spmi_bus {
	qcom,pm6150l@4 {
		compatible = "qcom,spmi-pmic";
		reg = <4 SPMI_USID>;
		#address-cells = <2>;
		#size-cells = <0>;

		pm6150l_revid: qcom,revid@100 {
			compatible = "qcom,qpnp-revid";
			reg = <0x100 0x100>;
		};

		qcom,power-on@800 {
			compatible = "qcom,qpnp-power-on";
			reg = <0x800 0x100>;
		};

		pm6150l_tz: qcom,temp-alarm@2400 {
			compatible = "qcom,spmi-temp-alarm";
			reg = <0x2400 0x100>;
			interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
			#thermal-sensor-cells = <0>;
			qcom,temperature-threshold-set = <1>;
		};

		pm6150l_bcl: bcl@3d00 {
			compatible = "qcom,bcl-v5";
			reg = <0x3d00 0x100>;
			interrupts = <0x4 0x3d 0x0 IRQ_TYPE_NONE>,
					<0x4 0x3d 0x1 IRQ_TYPE_NONE>,
					<0x4 0x3d 0x2 IRQ_TYPE_NONE>;
			interrupt-names = "bcl-lvl0",
						"bcl-lvl1",
						"bcl-lvl2";
			#thermal-sensor-cells = <1>;
		};

		pm6150l_vadc: vadc@3100 {
			compatible = "qcom,spmi-adc5";
			reg = <0x3100 0x100>;
			#address-cells = <1>;
			#size-cells = <0>;
			interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "eoc-int-en-set";
			qcom,adc-vdd-reference = <1875>;
			#io-channel-cells = <1>;
			io-channel-ranges;

			/* Channel node */
			ref_gnd {
				reg = <ADC_REF_GND>;
				label = "ref_gnd";
				qcom,pre-scaling = <1 1>;
			};

			vref_1p25 {
				reg = <ADC_1P25VREF>;
				label = "vref_1p25";
				qcom,pre-scaling = <1 1>;
			};

			die_temp {
				reg = <ADC_DIE_TEMP>;
				label = "die_temp";
				qcom,pre-scaling = <1 1>;
			};

			vph_pwr {
				reg = <ADC_VPH_PWR>;
				label = "vph_pwr";
				qcom,pre-scaling = <1 3>;
			};
		};

		pm6150l_adc_tm: adc_tm@3500 {
			compatible = "qcom,adc-tm5";
			reg = <0x3500 0x100>;
			interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "thr-int-en";
			#address-cells = <1>;
			#size-cells = <0>;
			#thermal-sensor-cells = <1>;
		};

		pm6150l_clkdiv: clock-controller@5b00 {
			compatible = "qcom,spmi-clkdiv";
			reg = <0x5b00 0x100>;
			#clock-cells = <1>;
			qcom,num-clkdivs = <1>;
			clock-output-names = "pm6150l_div_clk1";
			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";
			status = "disabled";
		};

		pm6150l_gpios: pinctrl@c000 {
			compatible = "qcom,spmi-gpio";
			reg = <0xc000 0xc00>;
			interrupts = <0x4 0xc0 0 IRQ_TYPE_NONE>,
					<0x4 0xc1 0 IRQ_TYPE_NONE>,
					<0x4 0xc2 0 IRQ_TYPE_NONE>,
					<0x4 0xc3 0 IRQ_TYPE_NONE>,
					<0x4 0xc4 0 IRQ_TYPE_NONE>,
					<0x4 0xc5 0 IRQ_TYPE_NONE>,
					<0x4 0xc6 0 IRQ_TYPE_NONE>,
					<0x4 0xc7 0 IRQ_TYPE_NONE>,
					<0x4 0xc8 0 IRQ_TYPE_NONE>,
					<0x4 0xc9 0 IRQ_TYPE_NONE>,
					<0x4 0xca 0 IRQ_TYPE_NONE>,
					<0x4 0xcb 0 IRQ_TYPE_NONE>;
			interrupt-names = "pm6150l_gpio1", "pm6150l_gpio2",
					"pm6150l_gpio3", "pm6150l_gpio4",
					"pm6150l_gpio5", "pm6150l_gpio6",
					"pm6150l_gpio7", "pm6150l_gpio8",
					"pm6150l_gpio9", "pm6150l_gpio10",
					"pm6150l_gpio11", "pm6150l_gpio12";
			gpio-controller;
			#gpio-cells = <2>;
		};
	};

	qcom,pm6150l@5 {
		compatible ="qcom,spmi-pmic";
		reg = <5 SPMI_USID>;
		#address-cells = <2>;
		#size-cells = <0>;

		pm6150l_pwm_1: qcom,pwms@bc00 {
			status = "disabled";
			compatible = "qcom,pwm-lpg";
			reg = <0xbc00 0x100>;
			reg-names = "lpg-base";
			qcom,num-lpg-channels = <1>;
			#pwm-cells = <2>;
		};

		pm6150l_lcdb: qcom,lcdb@ec00 {
			compatible = "qcom,qpnp-lcdb-regulator";
			#address-cells = <1>;
			#size-cells = <1>;
			reg = <0xec00 0x100>;
			interrupts = <0x5 0xec 0x1 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "sc-irq";
			qcom,pmic-revid = <&pm6150l_revid>;
			qcom,voltage-step-ramp;
			status = "disabled";

			lcdb_ldo_vreg: ldo {
				label = "ldo";
				regulator-name = "lcdb_ldo";
				regulator-min-microvolt = <4000000>;
				regulator-max-microvolt = <6000000>;
			};

			lcdb_ncp_vreg: ncp {
				label = "ncp";
				regulator-name = "lcdb_ncp";
				regulator-min-microvolt = <4000000>;
				regulator-max-microvolt = <6000000>;
			};

			lcdb_bst_vreg: bst {
				label = "bst";
				regulator-name = "lcdb_bst";
				regulator-min-microvolt = <4700000>;
				regulator-max-microvolt = <6275000>;
			};
		};

		flash_led: qcom,leds@d300 {
			compatible = "qcom,qpnp-flash-led-v2";
			status = "okay";
			reg = <0xd300 0x100>;
			label = "flash";
			interrupts = <0x5 0xd3 0x0 IRQ_TYPE_EDGE_RISING>,
				     <0x5 0xd3 0x3 IRQ_TYPE_EDGE_RISING>,
				     <0x5 0xd3 0x4 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "led-fault-irq",
					  "all-ramp-down-done-irq",
					  "all-ramp-up-done-irq";
			qcom,hdrm-auto-mode;
			qcom,short-circuit-det;
			qcom,open-circuit-det;
			qcom,vph-droop-det;
			qcom,thermal-derate-en;
			qcom,thermal-derate-current = <200 500 1000>;
			qcom,isc-delay = <192>;
			qcom,pmic-revid = <&pm6150l_revid>;

			pm6150l_flash0: qcom,flash_0 {
				label = "flash";
				qcom,led-name = "led:flash_0";
				qcom,max-current = <1500>;
				qcom,default-led-trigger = "flash0_trigger";
				qcom,id = <0>;
				qcom,current-ma = <1000>;
				qcom,duration-ms = <1280>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <325>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
			};

			pm6150l_flash1: qcom,flash_1 {
				label = "flash";
				qcom,led-name = "led:flash_1";
				qcom,max-current = <1500>;
				qcom,default-led-trigger = "flash1_trigger";
				qcom,id = <1>;
				qcom,current-ma = <1000>;
				qcom,duration-ms = <1280>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <325>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
			};

			pm6150l_flash2: qcom,flash_2 {
				label = "flash";
				qcom,led-name = "led:flash_2";
				qcom,max-current = <750>;
				qcom,default-led-trigger = "flash2_trigger";
				qcom,id = <2>;
				qcom,current-ma = <500>;
				qcom,duration-ms = <1280>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <325>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
				status = "disabled";
			};

			pm6150l_torch0: qcom,torch_0 {
				label = "torch";
				qcom,led-name = "led:torch_0";
				qcom,max-current = <500>;
				qcom,default-led-trigger = "torch0_trigger";
				qcom,id = <0>;
				qcom,current-ma = <300>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <325>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
			};

			pm6150l_torch1: qcom,torch_1 {
				label = "torch";
				qcom,led-name = "led:torch_1";
				qcom,max-current = <500>;
				qcom,default-led-trigger = "torch1_trigger";
				qcom,id = <1>;
				qcom,current-ma = <300>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <325>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
			};

			pm6150l_torch2: qcom,torch_2 {
				label = "torch";
				qcom,led-name = "led:torch_2";
				qcom,max-current = <500>;
				qcom,default-led-trigger = "torch2_trigger";
				qcom,id = <2>;
				qcom,current-ma = <300>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <325>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
				status = "disabled";
			};

			pm6150l_switch0: qcom,led_switch_0 {
				label = "switch";
				qcom,led-name = "led:switch_0";
				qcom,led-mask = <1>;
				qcom,default-led-trigger = "switch0_trigger";
			};

			pm6150l_switch1: qcom,led_switch_1 {
				label = "switch";
				qcom,led-name = "led:switch_1";
				qcom,led-mask = <2>;
				qcom,default-led-trigger = "switch1_trigger";
			};

			pm6150l_switch2: qcom,led_switch_2 {
				label = "switch";
				qcom,led-name = "led:switch_2";
				qcom,led-mask = <3>;
				qcom,default-led-trigger = "switch2_trigger";
			};
		};

		pm6150l_wled: qcom,wled@d800 {
			compatible = "qcom,pm6150l-spmi-wled";
			reg = <0xd800 0x100>, <0xd900 0x100>;
			reg-names = "wled-ctrl-base", "wled-sink-base";
			label = "backlight";
			interrupts = <0x5 0xd8 0x1 IRQ_TYPE_EDGE_RISING>,
				     <0x5 0xd8 0x4 IRQ_TYPE_EDGE_BOTH>,
				     <0x5 0xd8 0x5 IRQ_TYPE_EDGE_BOTH>;
			interrupt-names = "ovp-irq", "pre-flash-irq",
					  "flash-irq";
			qcom,pmic-revid = <&pm6150l_revid>;
			qcom,auto-calibration;
			status = "disabled";

			wled_flash: qcom,wled-flash {
				label = "flash";
				qcom,default-led-trigger = "wled_flash";
			};

			wled_torch: qcom,wled-torch {
				label = "torch";
				qcom,default-led-trigger = "wled_torch";
				qcom,wled-torch-timer = <1200>;
			};

			wled_switch: qcom,wled-switch {
				label = "switch";
				qcom,default-led-trigger = "wled_switch";
			};
		};

		pm6150l_lpg: qcom,pwms@b100 {
			compatible = "qcom,pwm-lpg";
			reg = <0xb100 0x300>, <0xb000 0x100>;
			reg-names = "lpg-base", "lut-base";
			#pwm-cells = <2>;
			qcom,num-lpg-channels = <3>;
			qcom,lut-patterns = <0 10 20 30 40 50 60 70 80 90 100
						90 80 70 60 50 40 30 20 10 0>;
			lpg1 {
				qcom,lpg-chan-id = <1>;
				qcom,ramp-step-ms = <100>;
				qcom,ramp-pause-hi-count = <2>;
				qcom,ramp-pause-lo-count = <2>;
				qcom,ramp-low-index = <0>;
				qcom,ramp-high-index = <20>;
				qcom,ramp-from-low-to-high;
				qcom,ramp-pattern-repeat;
			};

			lpg2 {
				qcom,lpg-chan-id = <2>;
				qcom,ramp-step-ms = <100>;
				qcom,ramp-pause-hi-count = <2>;
				qcom,ramp-pause-lo-count = <2>;
				qcom,ramp-low-index = <0>;
				qcom,ramp-high-index = <20>;
				qcom,ramp-from-low-to-high;
				qcom,ramp-pattern-repeat;
			};

			lpg3 {
				qcom,lpg-chan-id = <3>;
				qcom,ramp-step-ms = <100>;
				qcom,ramp-pause-hi-count = <2>;
				qcom,ramp-pause-lo-count = <2>;
				qcom,ramp-low-index = <0>;
				qcom,ramp-high-index = <20>;
				qcom,ramp-from-low-to-high;
				qcom,ramp-pattern-repeat;
			};
		};

		pm6150l_rgb_led: qcom,leds@d000 {
			compatible = "qcom,tri-led";
			reg = <0xd000 0x100>;
			red {
				label = "red";
				pwms = <&pm6150l_lpg 0 1000000>;
				led-sources = <0>;
				linux,default-trigger = "timer";
			};

			green {
				label = "green";
				pwms = <&pm6150l_lpg 1 1000000>;
				led-sources = <1>;
				linux,default-trigger = "timer";
			};

			blue {
				label = "blue";
				pwms = <&pm6150l_lpg 2 1000000>;
				led-sources = <2>;
				linux,default-trigger = "timer";
			};
		};

		pm6150a_amoled: qcom,amoled {
			compatible = "qcom,qpnp-amoled-regulator";
			status = "disabled";

			oledb_vreg: oledb@e000 {
				reg = <0xe000 0x100>;
				reg-names = "oledb_base";
				regulator-name = "oledb";
				regulator-min-microvolt = <4925000>;
				regulator-max-microvolt = <8100000>;
				qcom,swire-control;
			};

			ab_vreg: ab@de00 {
				reg = <0xde00 0x100>;
				reg-names = "ab_base";
				regulator-name = "ab";
				regulator-min-microvolt = <4600000>;
				regulator-max-microvolt = <6100000>;
				qcom,swire-control;
			};

			ibb_vreg: ibb@dc00 {
				reg = <0xdc00 0x100>;
				reg-names = "ibb_base";
				regulator-name = "ibb";
				regulator-min-microvolt = <800000>;
				regulator-max-microvolt = <5400000>;
				qcom,swire-control;
			};
		};
	};
};

&thermal_zones {
	pm6150l_temp_alarm: pm6150l-tz {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "step_wise";
		thermal-sensors = <&pm6150l_tz>;
		wake-capable-sensor;

		trips {
			pm6150l_trip0: trip0 {
				temperature = <95000>;
				hysteresis = <0>;
				type = "passive";
			};

			pm6150l_trip1: trip1 {
				temperature = <115000>;
				hysteresis = <0>;
				type = "passive";
			};

			trip2 {
				temperature = <145000>;
				hysteresis = <0>;
				type = "passive";
			};
		};
	};

	pm6150l-vph-lvl0 {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "low_limits_cap";
		thermal-sensors = <&pm6150l_bcl 2>;
		wake-capable-sensor;
		tracks-low;

		trips {
			vph_lvl0: vph-lvl0 {
				temperature = <3000>;
				hysteresis = <200>;
				type = "passive";
			};
		};
	};

	pm6150l-vph-lvl1 {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "low_limits_cap";
		thermal-sensors = <&pm6150l_bcl 3>;
		wake-capable-sensor;
		tracks-low;

		trips {
			vph_lvl1:vph-lvl1 {
				temperature = <2750>;
				hysteresis = <200>;
				type = "passive";
			};
		};
	};

	pm6150l-vph-lvl2 {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "low_limits_cap";
		thermal-sensors = <&pm6150l_bcl 4>;
		wake-capable-sensor;
		tracks-low;

		trips {
			vph_lvl2:vph-lvl2 {
				temperature = <2500>;
				hysteresis = <200>;
				type = "passive";
			};
		};
	};

	pm6150l-bcl-lvl0 {
		polling-delay-passive = <100>;
		polling-delay = <0>;
		thermal-governor = "step_wise";
		thermal-sensors = <&pm6150l_bcl 5>;
		wake-capable-sensor;

		trips {
			l_bcl_lvl0: l-bcl-lvl0 {
				temperature = <1>;
				hysteresis = <1>;
				type = "passive";
			};
		};
	};

	pm6150l-bcl-lvl1 {
		polling-delay-passive = <100>;
		polling-delay = <0>;
		thermal-governor = "step_wise";
		thermal-sensors = <&pm6150l_bcl 6>;
		wake-capable-sensor;

		trips {
			l_bcl_lvl1: l-bcl-lvl1 {
				temperature = <1>;
				hysteresis = <1>;
				type = "passive";
			};
		};
	};

	pm6150l-bcl-lvl2 {
		polling-delay-passive = <100>;
		polling-delay = <0>;
		thermal-governor = "step_wise";
		thermal-sensors = <&pm6150l_bcl 7>;
		wake-capable-sensor;

		trips {
			l_bcl_lvl2: l-bcl-lvl2 {
				temperature = <1>;
				hysteresis = <1>;
				type = "passive";
			};
		};
	};
};