#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
#include <dt-bindings/iio/qcom,spmi-vadc.h>

&spmi_bus {
	qcom,pmi632@2 {
		compatible = "qcom,spmi-pmic";
		reg = <0x2 0x0>;
		#address-cells = <2>;
		#size-cells = <0>;

		pmi632_revid: qcom,revid@100 {
			compatible = "qcom,qpnp-revid";
			reg = <0x100 0x100>;
		};

		pmi632_pon: qcom,power-on@800 {
			compatible = "qcom,qpnp-power-on";
			reg = <0x800 0x100>;
		};

		pmi632_vadc: vadc@3100 {
			compatible = "qcom,spmi-adc5-lite";
			reg = <0x3100 0x100>, <0x3700 0x100>;
			reg-names = "adc5-usr-base", "adc5-cal-base";
			#address-cells = <1>;
			#size-cells = <0>;
			interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "eoc-int-en-set";
			qcom,adc-vdd-reference = <1875>;
			#io-channel-cells = <1>;
			io-channel-ranges;
			qcom,pmic-revid = <&pmi632_revid>;

			/* Channel nodes */
			ref_gnd {
				reg = <ADC_REF_GND>;
				label = "ref_gnd";
				qcom,pre-scaling = <1 1>;
			};

			vref_1p25 {
				reg = <ADC_1P25VREF>;
				label = "vref_1p25";
				qcom,pre-scaling = <1 1>;
			};

			die_temp {
				reg = <ADC_DIE_TEMP>;
				label = "die_temp";
				qcom,pre-scaling = <1 1>;
			};

			vph_pwr {
				reg = <ADC_VPH_PWR>;
				label = "vph_pwr";
				qcom,pre-scaling = <1 3>;
			};

			vbat_sns {
				reg = <ADC_VBAT_SNS>;
				label = "vbat_sns";
				qcom,pre-scaling = <1 3>;
			};

			usb_in_i_uv {
				reg = <ADC_USB_IN_I>;
				label = "usb_in_i_uv";
				qcom,pre-scaling = <1 1>;
			};

			usb_in_v_div_16 {
				reg = <ADC_USB_IN_V_16>;
				label = "usb_in_v_div_16";
				qcom,pre-scaling = <1 16>;
			};

			chg_temp {
				reg = <ADC_CHG_TEMP>;
				label = "chg_temp";
				qcom,pre-scaling = <1 1>;
			};

			bat_therm {
				reg = <ADC_BAT_THERM_PU2>;
				label = "bat_therm";
				qcom,ratiometric;
				qcom,hw-settle-time = <200>;
				qcom,pre-scaling = <1 1>;
			};

			bat_therm_30k {
				reg = <ADC_BAT_THERM_PU1>;
				label = "bat_therm_30k";
				qcom,ratiometric;
				qcom,hw-settle-time = <200>;
				qcom,pre-scaling = <1 1>;
			};

			bat_therm_400k {
				reg = <ADC_BAT_THERM_PU3>;
				label = "bat_therm_400k";
				qcom,ratiometric;
				qcom,hw-settle-time = <200>;
				qcom,pre-scaling = <1 1>;
			};

			bat_id {
				reg = <ADC_BAT_ID_PU2>;
				label = "bat_id";
				qcom,ratiometric;
				qcom,hw-settle-time = <200>;
				qcom,pre-scaling = <1 1>;
			};

			i_parallel {
				reg = <ADC_PARALLEL_ISENSE>;
				label = "i_parallel";
				qcom,pre-scaling = <1 1>;
			};

			v_i_int_ext {
				reg = <ADC_INT_EXT_ISENSE_VBAT_VDATA>;
				label = "v_i_int_vbat_vdata";
				qcom,pre-scaling = <1 1>;
			};

			v_i_parallel {
				reg = <ADC_PARALLEL_ISENSE_VBAT_VDATA>;
				label = "v_i_parallel_vbat_vdata";
				qcom,pre-scaling = <1 1>;
			};

		};

		pmi632_adc_tm: adc_tm@3500 {
			compatible = "qcom,adc-tm5";
			reg = <0x3500 0x100>;
			interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "thr-int-en";
			#address-cells = <1>;
			#size-cells = <0>;
			#thermal-sensor-cells = <1>;
		};

		pmi632_tz: qcom,temp-alarm@2400 {
			compatible = "qcom,spmi-temp-alarm";
			reg = <0x2400 0x100>;
			interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
			#thermal-sensor-cells = <0>;
			qcom,temperature-threshold-set = <1>;
		};

		pmi632_gpios: pinctrl@c000 {
			compatible = "qcom,spmi-gpio";
			reg = <0xc000 0x800>;
			interrupts = <0x2 0xc0 0 IRQ_TYPE_NONE>,
					<0x2 0xc1 0 IRQ_TYPE_NONE>,
					<0x2 0xc2 0 IRQ_TYPE_NONE>,
					<0x2 0xc3 0 IRQ_TYPE_NONE>,
					<0x2 0xc4 0 IRQ_TYPE_NONE>,
					<0x2 0xc5 0 IRQ_TYPE_NONE>,
					<0x2 0xc6 0 IRQ_TYPE_NONE>,
					<0x2 0xc7 0 IRQ_TYPE_NONE>;
			interrupt-names = "pmi632_gpio1", "pmi632_gpio2",
					"pmi632_gpio3", "pmi632_gpio4",
					"pmi632_gpio5", "pmi632_gpio6",
					"pmi632_gpio7", "pmi632_gpio8";
			gpio-controller;
			#gpio-cells = <2>;
		};

		pmi632_charger: qcom,qpnp-smb5 {
			compatible = "qcom,qpnp-smb5";
			#address-cells = <1>;
			#size-cells = <1>;
			#cooling-cells = <2>;

			qcom,pmic-revid = <&pmi632_revid>;
			io-channels = <&pmi632_vadc ADC_USB_IN_V_16>,
				      <&pmi632_vadc ADC_USB_IN_I>,
				      <&pmi632_vadc ADC_CHG_TEMP>,
				      <&pmi632_vadc ADC_DIE_TEMP>;
			io-channel-names = "usb_in_voltage",
					   "usb_in_current",
					   "chg_temp",
					   "die_temp";

			qcom,chgr@1000 {
				reg = <0x1000 0x100>;
				interrupts =
					<0x2 0x10 0x0 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x1 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x3 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x4 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x5 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x6 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x10 0x7 IRQ_TYPE_EDGE_RISING>;

				interrupt-names = "chgr-error",
						  "chg-state-change",
						  "step-chg-state-change",
						  "step-chg-soc-update-fail",
						  "step-chg-soc-update-req",
						  "fg-fvcal-qualified",
						  "vph-alarm",
						  "vph-drop-prechg";
			};

			qcom,dcdc@1100 {
				reg = <0x1100 0x100>;
				interrupts =
					<0x2 0x11 0x0 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x11 0x1 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x11 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x11 0x3 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x11 0x4 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x11 0x5 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x11 0x6 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x11 0x7 IRQ_TYPE_EDGE_BOTH>;

				interrupt-names = "otg-fail",
						  "otg-oc-disable-sw",
						  "otg-oc-hiccup",
						  "bsm-active",
						  "high-duty-cycle",
						  "input-current-limiting",
						  "concurrent-mode-disable",
						  "switcher-power-ok";
			};

			qcom,batif@1200 {
				reg = <0x1200 0x100>;
				interrupts =
					<0x2 0x12 0x0 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x12 0x1 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x12 0x2 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x12 0x3 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x12 0x4 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x12 0x5 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x12 0x6 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x12 0x7 IRQ_TYPE_EDGE_BOTH>;

				interrupt-names = "bat-temp",
						  "all-chnl-conv-done",
						  "bat-ov",
						  "bat-low",
						  "bat-therm-or-id-missing",
						  "bat-terminal-missing",
						  "buck-oc",
						  "vph-ov";
			};

			qcom,usb@1300 {
				reg = <0x1300 0x100>;
				interrupts =
					<0x2 0x13 0x0 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x13 0x1 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x13 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x13 0x3 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x13 0x4 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x13 0x5 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x13 0x6 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x13 0x7 IRQ_TYPE_EDGE_RISING>;

				interrupt-names = "usbin-collapse",
						  "usbin-vashdn",
						  "usbin-uv",
						  "usbin-ov",
						  "usbin-plugin",
						  "usbin-revi-change",
						  "usbin-src-change",
						  "usbin-icl-change";
			};

			qcom,typec@1500 {
				reg = <0x1500 0x100>;
				interrupts =
					<0x2 0x15 0x0 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x15 0x1 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x15 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x15 0x3 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x15 0x4 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x15 0x5 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x15 0x6 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x15 0x7 IRQ_TYPE_EDGE_RISING>;

				interrupt-names = "typec-or-rid-detect-change",
						  "typec-vpd-detect",
						  "typec-cc-state-change",
						  "typec-vconn-oc",
						  "typec-vbus-change",
						  "typec-attach-detach",
						  "typec-legacy-cable-detect",
						  "typec-try-snk-src-detect";
			};

			qcom,misc@1600 {
				reg = <0x1600 0x100>;
				interrupts =
					<0x2 0x16 0x0 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x16 0x1 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x16 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x16 0x3 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x16 0x4 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x16 0x5 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x16 0x6 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x16 0x7 IRQ_TYPE_EDGE_RISING>;

				interrupt-names = "wdog-snarl",
						  "wdog-bark",
						  "aicl-fail",
						  "aicl-done",
						  "smb-en",
						  "imp-trigger",
						  "temp-change",
						  "temp-change-smb";
			};

			qcom,schgm-flash@a600 {
				reg = <0xa600 0x100>;
				interrupts =
					<0x2 0xa6 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0xa6 0x5 IRQ_TYPE_EDGE_RISING>,
					<0x2 0xa6 0x6 IRQ_TYPE_EDGE_RISING>,
					<0x2 0xa6 0x7 IRQ_TYPE_EDGE_BOTH>;

				interrupt-names = "flash-state-change",
						"ilim1-s1",
						"ilim2-s2",
						"vreg-ok";
			};
			smb5_vbus: qcom,smb5-vbus {
				regulator-name = "smb5-vbus";
			};
		};

		pmi632_qg: qpnp,qg {
			compatible = "qcom,qpnp-qg";
			#address-cells = <1>;
			#size-cells = <1>;

			qcom,pmic-revid = <&pmi632_revid>;
			io-channels = <&pmi632_vadc ADC_BAT_THERM_PU2>,
				      <&pmi632_vadc ADC_BAT_ID_PU2>;
			io-channel-names = "batt-therm",
					   "batt-id";

			qcom,qgauge@4800 {
				status = "okay";
				reg = <0x4800 0x100>;
				interrupts =
					<0x2 0x48 0x0 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x48 0x1 IRQ_TYPE_EDGE_BOTH>,
					<0x2 0x48 0x2 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x48 0x3 IRQ_TYPE_EDGE_RISING>,
					<0x2 0x48 0x4 IRQ_TYPE_EDGE_RISING>;
				interrupt-names = "qg-batt-missing",
						  "qg-vbat-low",
						  "qg-vbat-empty",
						  "qg-fifo-done",
						  "qg-good-ocv";
			};

			qcom,qg-sdam@b100 {
				status = "okay";
				reg = <0xb100 0x100>;
			};
		};

		pmi632_pbs_client3: qcom,pbs@7400 {
			compatible = "qcom,qpnp-pbs";
			reg = <0x7400 0x100>;
		};

		pmi632_sdam7: qcom,sdam@b600 {
			compatible = "qcom,spmi-sdam";
			reg = <0xb600 0x100>;
		};

		bcl_sensor: bcl@3d00 {
			compatible = "qcom,bcl-v5";
			reg = <0x3d00 0x100>;
			interrupts = <0x2 0x3d 0x0 IRQ_TYPE_NONE>,
					<0x2 0x3d 0x1 IRQ_TYPE_NONE>,
					<0x2 0x3d 0x2 IRQ_TYPE_NONE>;
			interrupt-names = "bcl-lvl0",
						"bcl-lvl1",
						"bcl-lvl2";
			qcom,ibat-use-qg-adc-5a;
			#thermal-sensor-cells = <1>;
		};

		bcl_soc: bcl-soc {
			compatible = "qcom,msm-bcl-soc";
			#thermal-sensor-cells = <0>;
		};
	};

	pmi632_3: qcom,pmi632@3 {
		compatible ="qcom,spmi-pmic";
		reg = <0x3 0x0>;
		#address-cells = <2>;
		#size-cells = <0>;

		pmi632_vib: qcom,vibrator@5700 {
			compatible = "qcom,qpnp-vibrator-ldo";
			reg = <0x5700 0x100>;
			qcom,vib-ldo-volt-uv = <3000000>;
			qcom,disable-overdrive;
		};

		pmi632_pwm: qcom,pwms@b300 {
			compatible = "qcom,pwm-lpg";
			reg = <0xb300 0x500>;
			reg-names = "lpg-base";
			#pwm-cells = <2>;
			qcom,num-lpg-channels = <5>;
			nvmem-names = "ppg_sdam";
			nvmem = <&pmi632_sdam7>;
			qcom,pbs-client = <&pmi632_pbs_client3>;
			qcom,lut-sdam-base = <0x80>;
			qcom,lut-patterns = <0 0 0 14 28 42 56 70 84 100
						100 84 70 56 42 28 14 0 0 0>;
			lpg@1 {
				qcom,lpg-chan-id = <1>;
				qcom,ramp-step-ms = <200>;
				qcom,ramp-low-index = <0>;
				qcom,ramp-high-index = <19>;
				qcom,ramp-pattern-repeat;
				qcom,lpg-sdam-base = <0x48>;
			};

			lpg@2 {
				qcom,lpg-chan-id = <2>;
				qcom,ramp-step-ms = <200>;
				qcom,ramp-low-index = <0>;
				qcom,ramp-high-index = <19>;
				qcom,ramp-pattern-repeat;
				qcom,lpg-sdam-base = <0x56>;
			};

			lpg@3 {
				qcom,lpg-chan-id = <3>;
				qcom,ramp-step-ms = <200>;
				qcom,ramp-low-index = <0>;
				qcom,ramp-high-index = <19>;
				qcom,ramp-pattern-repeat;
				qcom,lpg-sdam-base = <0x64>;
			};
		};

		pmi632_rgb: qcom,leds@d000 {
			compatible = "qcom,tri-led";
			reg = <0xd000 0x100>;
			red {
				label = "red";
				pwms = <&pmi632_pwm 0 1000000>;
				led-sources = <0>;
				linux,default-trigger = "timer";
			};

			green {
				label = "green";
				pwms = <&pmi632_pwm 1 1000000>;
				led-sources = <1>;
				linux,default-trigger = "timer";
			};

			blue {
				label = "blue";
				pwms = <&pmi632_pwm 2 1000000>;
				led-sources = <2>;
				linux,default-trigger = "timer";
			};
		};

		pmi632_lcdb: qpnp-lcdb@ec00 {
			compatible = "qcom,qpnp-lcdb-regulator";
			#address-cells = <1>;
			#size-cells = <1>;
			reg = <0xec00 0x100>;
			interrupts = <0x3 0xec 0x1 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "sc-irq";

			qcom,pmic-revid = <&pmi632_revid>;
			qcom,voltage-step-ramp;

			lcdb_ldo_vreg: ldo {
				label = "ldo";
				regulator-name = "lcdb_ldo";
				regulator-min-microvolt = <4000000>;
				regulator-max-microvolt = <6000000>;
			};

			lcdb_ncp_vreg: ncp {
				label = "ncp";
				regulator-name = "lcdb_ncp";
				regulator-min-microvolt = <4000000>;
				regulator-max-microvolt = <6000000>;
			};

			lcdb_bst_vreg: bst {
				label = "bst";
				regulator-name = "lcdb_bst";
				regulator-min-microvolt = <4700000>;
				regulator-max-microvolt = <6275000>;
			};
		};

		flash_led: qcom,leds@d300 {
			compatible = "qcom,qpnp-flash-led-v2";
			status = "okay";
			reg = <0xd300 0x100>;
			label = "flash";
			interrupts = <0x3 0xd3 0x0 IRQ_TYPE_EDGE_RISING>,
				     <0x3 0xd3 0x3 IRQ_TYPE_EDGE_RISING>,
				     <0x3 0xd3 0x4 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "led-fault-irq",
					  "all-ramp-down-done-irq",
					  "all-ramp-up-done-irq";
			qcom,short-circuit-det;
			qcom,open-circuit-det;
			qcom,vph-droop-det;
			qcom,thermal-derate-en;
			qcom,thermal-derate-current = <200 500 1000>;
			qcom,isc-delay = <192>;
			qcom,pmic-revid = <&pmi632_revid>;

			pmi632_flash0: qcom,flash_0 {
				label = "flash";
				qcom,led-name = "led:flash_0";
				qcom,max-current = <1500>;
				qcom,default-led-trigger = "flash0_trigger";
				qcom,id = <0>;
				qcom,current-ma = <1000>;
				qcom,duration-ms = <1280>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <400>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
			};

			pmi632_flash1: qcom,flash_1 {
				label = "flash";
				qcom,led-name = "led:flash_1";
				qcom,max-current = <1500>;
				qcom,default-led-trigger = "flash1_trigger";
				qcom,id = <1>;
				qcom,current-ma = <1000>;
				qcom,duration-ms = <1280>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <400>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
			};

			pmi632_torch0: qcom,torch_0 {
				label = "torch";
				qcom,led-name = "led:torch_0";
				qcom,max-current = <500>;
				qcom,default-led-trigger = "torch0_trigger";
				qcom,id = <0>;
				qcom,current-ma = <300>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <400>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
			};

			pmi632_torch1: qcom,torch_1 {
				label = "torch";
				qcom,led-name = "led:torch_1";
				qcom,max-current = <500>;
				qcom,default-led-trigger = "torch1_trigger";
				qcom,id = <1>;
				qcom,current-ma = <300>;
				qcom,ires-ua = <12500>;
				qcom,hdrm-voltage-mv = <400>;
				qcom,hdrm-vol-hi-lo-win-mv = <100>;
			};

			pmi632_switch0: qcom,led_switch_0 {
				label = "switch";
				qcom,led-name = "led:switch_0";
				qcom,led-mask = <3>;
				qcom,default-led-trigger = "switch0_trigger";
			};

			pmi632_switch1: qcom,led_switch_1 {
				label = "switch";
				qcom,led-name = "led:switch_1";
				qcom,led-mask = <2>;
				qcom,default-led-trigger = "switch1_trigger";
			};

		};

	};
};

&thermal_zones {
	pmi632-tz {
		polling-delay-passive = <100>;
		polling-delay = <0>;
		thermal-governor = "step_wise";
		thermal-sensors = <&pmi632_tz>;
		wake-capable-sensor;

		trips {
			pmi632_trip0: trip0 {
				temperature = <95000>;
				hysteresis = <0>;
				type = "passive";
			};

			pmi632_trip1: trip1 {
				temperature = <115000>;
				hysteresis = <0>;
				type = "passive";
			};

			trip2 {
				temperature = <145000>;
				hysteresis = <0>;
				type = "passive";
			};
		};
	};

	pmi632-ibat-lvl0 {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "step_wise";
		thermal-sensors = <&bcl_sensor 0>;
		wake-capable-sensor;

		trips {
			pmi632_ibat_lvl0: ibat-lvl0 {
				temperature = <4000>;
				hysteresis = <200>;
				type = "passive";
			};
		};
	};

	pmi632-ibat-lvl1 {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "step_wise";
		thermal-sensors = <&bcl_sensor 1>;
		wake-capable-sensor;

		trips {
			pmi632_ibat_lvl1: ibat-lvl1 {
				temperature = <4200>;
				hysteresis = <200>;
				type = "passive";
			};
		};
	};

	pmi632-vbat-lvl0 {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "low_limits_cap";
		thermal-sensors = <&bcl_sensor 2>;
		wake-capable-sensor;
		tracks-low;

		trips {
			pmi632_vbat_lvl0: vbat-lvl0 {
				temperature = <3000>;
				hysteresis = <100>;
				type = "passive";
			};
		};
	};

	pmi632-vbat-lvl1 {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "low_limits_cap";
		thermal-sensors = <&bcl_sensor 3>;
		wake-capable-sensor;
		tracks-low;

		trips {
			pmi632_vbat_lvl1: vbat-lvl1 {
				temperature = <2800>;
				hysteresis = <100>;
				type = "passive";
			};
		};
	};

	pmi632-vbat-lvl2 {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "low_limits_cap";
		thermal-sensors = <&bcl_sensor 4>;
		wake-capable-sensor;
		tracks-low;

		trips {
			pmi632_vbat_lvl2: vbat-lvl1 {
				temperature = <2600>;
				hysteresis = <100>;
				type = "passive";
			};
		};
	};

	pmi632-bcl-lvl0 {
		polling-delay-passive = <100>;
		polling-delay = <0>;
		thermal-governor = "step_wise";
		thermal-sensors = <&bcl_sensor 5>;
		wake-capable-sensor;

		trips {
			bcl_lvl0: bcl-lvl0 {
				temperature = <1>;
				hysteresis = <1>;
				type = "passive";
			};
		};
	};

	pmi632-bcl-lvl1 {
		polling-delay-passive = <100>;
		polling-delay = <0>;
		thermal-governor = "step_wise";
		thermal-sensors = <&bcl_sensor 6>;
		wake-capable-sensor;

		trips {
			bcl_lvl1: bcl-lvl1 {
				temperature = <1>;
				hysteresis = <1>;
				type = "passive";
			};
		};
	};

	pmi632-bcl-lvl2 {
		polling-delay-passive = <100>;
		polling-delay = <0>;
		thermal-governor = "step_wise";
		thermal-sensors = <&bcl_sensor 7>;
		wake-capable-sensor;

		trips {
			bcl_lvl2: bcl-lvl2 {
				temperature = <1>;
				hysteresis = <1>;
				type = "passive";
			};
		};
	};

	soc {
		polling-delay-passive = <100>;
		polling-delay = <0>;
		thermal-governor = "low_limits_cap";
		thermal-sensors = <&bcl_soc>;
		wake-capable-sensor;
		tracks-low;

		trips {
			pmi632_low_soc: low-soc {
				temperature = <10>;
				hysteresis = <0>;
				type = "passive";
			};
		};
	};
};