&soc {
	led_flash0: qcom,camera-flash@0 {
		cell-index = <0>;
		compatible = "qcom,camera-flash";
		qcom,flash-source = <&pm660l_flash0 &pm660l_flash1>;
		qcom,torch-source = <&pm660l_torch0 &pm660l_torch1>;
		qcom,switch-source = <&pm660l_switch0>;
		status = "ok";
	};

	led_flash1: qcom,camera-flash@1 {
		cell-index = <1>;
		compatible = "qcom,camera-flash";
		qcom,flash-source = <&pm660l_flash2>;
		qcom,torch-source = <&pm660l_torch2>;
		qcom,switch-source = <&pm660l_switch1>;
		status = "ok";
	};

	cam_avdd_gpio_regulator: cam_avdd_fixed_regulator {
		compatible = "regulator-fixed";
		regulator-name = "cam_avdd_gpio_regulator";
		regulator-min-microvolt = <3600000>;
		regulator-max-microvolt = <3600000>;
		enable-active-high;
		gpio = <&tlmm 51 0>;
		vin-supply = <&pm660l_bob>;
	};

	cam_actuator_regulator: cam_actuator_fixed_regulator {
		compatible = "regulator-fixed";
		regulator-name = "cam_actuator_regulator";
		regulator-min-microvolt = <3600000>;
		regulator-max-microvolt = <3600000>;
		enable-active-high;
		gpio = <&tlmm 50 0>;
		vin-supply = <&pm660l_bob>;
	};

	cam_dvdd_gpio_regulator: cam_dvdd_fixed_regulator {
		compatible = "regulator-fixed";
		regulator-name = "cam_dvdd_gpio_regulator";
		regulator-min-microvolt = <1350000>;
		regulator-max-microvolt = <1350000>;
		enable-active-high;
		gpio = <&pm660l_gpios 3 0>;
		pinctrl-names = "default";
		pinctrl-0 = <&cam_sensor_eldo3_default>;
		vin-supply = <&pm660_s5>;
	};

	cam_rear_dvdd_gpio_regulator: cam_rear_dvdd_fixed_regulator {
		compatible = "regulator-fixed";
		regulator-name = "cam_rear_dvdd_gpio_regulator";
		regulator-min-microvolt = <1350000>;
		regulator-max-microvolt = <1350000>;
		enable-active-high;
		gpio = <&pm660l_gpios 4 0>;
		pinctrl-names = "default";
		pinctrl-0 = <&cam_sensor_eldo4_default>;
		vin-supply = <&pm660_s5>;
	};
};

&cci {
	actuator0: qcom,actuator@0 {
		cell-index = <0>;
		reg = <0x0>;
		compatible = "qcom,actuator";
		qcom,cci-master = <0>;
		cam_vaf-supply = <&cam_actuator_regulator>;
		qcom,cam-vreg-name = "cam_vaf";
		qcom,cam-vreg-min-voltage = <3600000>;
		qcom,cam-vreg-max-voltage = <3600000>;
		qcom,cam-vreg-op-mode = <0>;
	};

	actuator1: qcom,actuator@1 {
		cell-index = <1>;
		reg = <0x1>;
		compatible = "qcom,actuator";
		qcom,cci-master = <1>;
		cam_vaf-supply = <&cam_actuator_regulator>;
		qcom,cam-vreg-name = "cam_vaf";
		qcom,cam-vreg-min-voltage = <3600000>;
		qcom,cam-vreg-max-voltage = <3600000>;
		qcom,cam-vreg-op-mode = <0>;
	};

	actuator2: qcom,actuator@2 {
		cell-index = <2>;
		reg = <0x2>;
		compatible = "qcom,actuator";
		qcom,cci-master = <1>;
		cam_vaf-supply = <&cam_actuator_regulator>;
		qcom,cam-vreg-name = "cam_vaf";
		qcom,cam-vreg-min-voltage = <3600000>;
		qcom,cam-vreg-max-voltage = <3600000>;
		qcom,cam-vreg-op-mode = <0>;
	};

	ois0: qcom,ois@0 {
		cell-index = <0>;
		reg = <0x0>;
		compatible = "qcom,ois";
		qcom,cci-master = <0>;
		cam_vaf-supply = <&cam_actuator_regulator>;
		qcom,cam-vreg-name = "cam_vaf";
		qcom,cam-vreg-min-voltage = <3600000>;
		qcom,cam-vreg-max-voltage = <3600000>;
		qcom,cam-vreg-op-mode = <0>;
		status = "disabled";
	};

	tof0: qcom,tof@29{
		cell-index = <0>;
		reg = <0x29>;
		compatible = "st,stmvl53l0";
		qcom,cci-master = <0>;
		cam_laser-supply = <&cam_actuator_regulator>;
		qcom,cam-vreg-name =  "cam_laser";
		qcom,cam-vreg-min-voltage = <3600000>;
		qcom,cam-vreg-max-voltage = <3600000>;
		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_tof_active>;
		pinctrl-1 = <&cam_tof_suspend>;
		stm,irq-gpio = <&tlmm 45  0x2008>;
		gpios = <&tlmm 42 0>;
		qcom,gpio-req-tbl-num = <0>;
		qcom,gpio-req-tbl-flags = <0>;
		qcom,gpio-req-tbl-label = "RNG_EN";
	};

	eeprom0: qcom,eeprom@0 {
		cell-index = <0>;
		reg = <0>;
		compatible = "qcom,eeprom";
		cam_vio-supply = <&pm660_l11>;
		cam_vana-supply = <&cam_avdd_gpio_regulator>;
		cam_vdig-supply = <&cam_rear_dvdd_gpio_regulator>;
		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
		qcom,cam-vreg-min-voltage = <1780000 0 0>;
		qcom,cam-vreg-max-voltage = <1950000 0 0>;
		qcom,cam-vreg-op-mode = <105000 0 0>;
		qcom,gpio-no-mux = <0>;
		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_sensor_mclk0_active
				&cam_sensor_rear_active
				&cam_actuator_vaf_active>;
		pinctrl-1 = <&cam_sensor_mclk0_suspend
				&cam_sensor_rear_suspend
				&cam_actuator_vaf_suspend>;
		gpios = <&tlmm 32 0>,
			<&tlmm 46 0>,
			<&tlmm 50 0>;
		qcom,gpio-reset = <1>;
		qcom,gpio-vaf = <2>;
		qcom,gpio-req-tbl-num = <0 1 2>;
		qcom,gpio-req-tbl-flags = <1 0 0>;
		qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
					"CAM_RESET0",
					"CAM_VAF";
		qcom,sensor-position = <0>;
		qcom,sensor-mode = <0>;
		qcom,cci-master = <0>;
		status = "ok";
		clocks = <&clock_mmss MCLK0_CLK_SRC>,
				<&clock_mmss MMSS_CAMSS_MCLK0_CLK>;
		clock-names = "cam_src_clk", "cam_clk";
		qcom,clock-rates = <24000000 0>;
	};

	eeprom1: qcom,eeprom@1 {
		cell-index = <1>;
		reg = <0x1>;
		compatible = "qcom,eeprom";
		cam_vio-supply = <&pm660_l11>;
		cam_vana-supply = <&cam_avdd_gpio_regulator>;
		cam_vdig-supply = <&cam_dvdd_gpio_regulator>;
		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
		qcom,cam-vreg-min-voltage = <1780000 0 0>;
		qcom,cam-vreg-max-voltage = <1950000 0 0>;
		qcom,cam-vreg-op-mode = <105000 0 0>;
		qcom,gpio-no-mux = <0>;
		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_sensor_mclk2_active
			&cam_sensor_rear2_active>;
		pinctrl-1 = <&cam_sensor_mclk2_suspend
			&cam_sensor_rear2_suspend>;
		gpios = <&tlmm 34 0>,
		    <&tlmm 48 0>;
		qcom,gpio-reset = <1>;
		qcom,gpio-req-tbl-num = <0 1>;
		qcom,gpio-req-tbl-flags = <1 0>;
		qcom,gpio-req-tbl-label = "CAMIF_MCLK",
				"CAM_RESET";
		qcom,sensor-position = <0>;
		qcom,sensor-mode = <0>;
		qcom,cci-master = <1>;
		status = "ok";
		clocks = <&clock_mmss MCLK2_CLK_SRC>,
		    <&clock_mmss MMSS_CAMSS_MCLK2_CLK>;
		clock-names = "cam_src_clk", "cam_clk";
		qcom,clock-rates = <24000000 0>;
	};

	eeprom2: qcom,eeprom@2 {
		cell-index = <2>;
		reg = <0x2>;
		compatible = "qcom,eeprom";
		cam_vio-supply = <&pm660_l11>;
		cam_vana-supply = <&pm660l_bob>;
		cam_vdig-supply = <&cam_dvdd_gpio_regulator>;
		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
		qcom,cam-vreg-min-voltage = <1780000 3300000 0>;
		qcom,cam-vreg-max-voltage = <1950000 3600000 0>;
		qcom,cam-vreg-op-mode = <105000 80000 0>;
		qcom,gpio-no-mux = <0>;
		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_sensor_mclk1_active
				 &cam_sensor_front_active
				&cam_actuator_vaf_active>;
		pinctrl-1 = <&cam_sensor_mclk1_suspend
				 &cam_sensor_front_suspend
				&cam_actuator_vaf_suspend>;
		gpios = <&tlmm 33 0>,
			<&tlmm 47 0>,
			<&tlmm 44 0>,
			<&tlmm 50 0>;
		qcom,gpio-reset = <1>;
		qcom,gpio-vana = <2>;
		qcom,gpio-vaf = <3>;
		qcom,gpio-req-tbl-num = <0 1 2 3>;
		qcom,gpio-req-tbl-flags = <1 0 0 0>;
		qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
					"CAM_RESET2",
					"CAM_VANA",
					"CAM_VAF";
		qcom,sensor-position = <1>;
		qcom,sensor-mode = <0>;
		qcom,cci-master = <1>;
		status = "ok";
		clocks = <&clock_mmss MCLK1_CLK_SRC>,
			<&clock_mmss MMSS_CAMSS_MCLK1_CLK>;
		clock-names = "cam_src_clk", "cam_clk";
		qcom,clock-rates = <24000000 0>;
	};

	qcom,camera@0 {
		cell-index = <0>;
		compatible = "qcom,camera";
		reg = <0x0>;
		qcom,csiphy-sd-index = <0>;
		qcom,csid-sd-index = <0>;
		qcom,mount-angle = <90>;
		qcom,led-flash-src = <&led_flash0>;
		qcom,actuator-src = <&actuator0>;
		qcom,ois-src = <&ois0>;
		qcom,eeprom-src = <&eeprom0>;
		cam_vio-supply = <&pm660_l11>;
		cam_vana-supply = <&cam_avdd_gpio_regulator>;
		cam_vdig-supply = <&cam_rear_dvdd_gpio_regulator>;
		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
		qcom,cam-vreg-min-voltage = <1780000 0 0>;
		qcom,cam-vreg-max-voltage = <1950000 0 0>;
		qcom,cam-vreg-op-mode = <105000 0 0>;
		qcom,gpio-no-mux = <0>;
		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_sensor_mclk0_active
				 &cam_sensor_rear_active>;
		pinctrl-1 = <&cam_sensor_mclk0_suspend
				 &cam_sensor_rear_suspend>;
		gpios = <&tlmm 32 0>,
			<&tlmm 46 0>;
		qcom,gpio-reset = <1>;
		qcom,gpio-req-tbl-num = <0 1>;
		qcom,gpio-req-tbl-flags = <1 0>;
		qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
					"CAM_RESET0";
		qcom,sensor-position = <0>;
		qcom,sensor-mode = <0>;
		qcom,cci-master = <0>;
		status = "ok";
		clocks = <&clock_mmss MCLK0_CLK_SRC>,
				<&clock_mmss MMSS_CAMSS_MCLK0_CLK>;
		clock-names = "cam_src_clk", "cam_clk";
		qcom,clock-rates = <24000000 0>;
	};

	qcom,camera@1 {
		cell-index = <1>;
		compatible = "qcom,camera";
		reg = <0x1>;
		qcom,csiphy-sd-index = <1>;
		qcom,csid-sd-index = <2>;
		qcom,mount-angle = <90>;
		qcom,led-flash-src = <&led_flash0>;
		qcom,actuator-src = <&actuator1>;
		qcom,eeprom-src = <&eeprom1>;
		cam_vio-supply = <&pm660_l11>;
		cam_vana-supply = <&cam_avdd_gpio_regulator>;
		cam_vdig-supply = <&cam_dvdd_gpio_regulator>;
		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
		qcom,cam-vreg-min-voltage = <1780000 0 0>;
		qcom,cam-vreg-max-voltage = <1950000 0 0>;
		qcom,cam-vreg-op-mode = <105000 0 0>;
		qcom,gpio-no-mux = <0>;
		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_sensor_mclk2_active
				 &cam_sensor_rear2_active>;
		pinctrl-1 = <&cam_sensor_mclk2_suspend
				 &cam_sensor_rear2_suspend>;
		gpios = <&tlmm 34 0>,
			<&tlmm 48 0>;
		qcom,gpio-reset = <1>;
		qcom,gpio-req-tbl-num = <0 1>;
		qcom,gpio-req-tbl-flags = <1 0>;
		qcom,gpio-req-tbl-label = "CAMIF_MCLK",
					  "CAM_RESET";
		qcom,sensor-position = <0>;
		qcom,sensor-mode = <0>;
		qcom,cci-master = <1>;
		status = "ok";
		clocks = <&clock_mmss MCLK2_CLK_SRC>,
			<&clock_mmss MMSS_CAMSS_MCLK2_CLK>;
		clock-names = "cam_src_clk", "cam_clk";
		qcom,clock-rates = <24000000 0>;
	};

	qcom,camera@2 {
		cell-index = <2>;
		compatible = "qcom,camera";
		reg = <0x02>;
		qcom,csiphy-sd-index = <2>;
		qcom,csid-sd-index = <2>;
		qcom,mount-angle = <90>;
		qcom,actuator-src = <&actuator2>;
		qcom,eeprom-src = <&eeprom2>;
		cam_vio-supply = <&pm660_l11>;
		cam_vana-supply = <&cam_avdd_gpio_regulator>;
		cam_vdig-supply = <&cam_dvdd_gpio_regulator>;
		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
		qcom,cam-vreg-min-voltage = <1780000 0 0>;
		qcom,cam-vreg-max-voltage = <1950000 0 0>;
		qcom,cam-vreg-op-mode = <105000 0 0>;
		qcom,gpio-no-mux = <0>;
		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_sensor_mclk1_active
				 &cam_sensor_front_active>;
		pinctrl-1 = <&cam_sensor_mclk1_suspend
				 &cam_sensor_front_suspend>;
		gpios = <&tlmm 33 0>,
			<&tlmm 47 0>;
		qcom,gpio-reset = <1>;
		qcom,gpio-req-tbl-num = <0 1>;
		qcom,gpio-req-tbl-flags = <1 0>;
		qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
					"CAM_RESET2";
		qcom,sensor-position = <1>;
		qcom,sensor-mode = <0>;
		qcom,cci-master = <1>;
		status = "ok";
		clocks = <&clock_mmss MCLK1_CLK_SRC>,
			<&clock_mmss MMSS_CAMSS_MCLK1_CLK>;
		clock-names = "cam_src_clk", "cam_clk";
		qcom,clock-rates = <24000000 0>;
	};

	qcom,camera@3 {
		cell-index = <3>;
		compatible = "qcom,camera";
		reg = <0x03>;
		qcom,csiphy-sd-index = <1>;
		qcom,csid-sd-index = <1>;
		qcom,mount-angle = <90>;
		qcom,led-flash-src = <&led_flash1>;
		qcom,actuator-src = <&actuator2>;
		qcom,eeprom-src = <&eeprom2>;
		cam_vio-supply = <&pm660_l11>;
		cam_vana-supply = <&cam_avdd_gpio_regulator>;
		cam_vdig-supply = <&cam_dvdd_gpio_regulator>;
		qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
		qcom,cam-vreg-min-voltage = <1780000 0 0>;
		qcom,cam-vreg-max-voltage = <1950000 0 0>;
		qcom,cam-vreg-op-mode = <105000 0 0>;
		qcom,gpio-no-mux = <0>;
		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_sensor_mclk3_active
				 &cam_sensor_front_iris_active>;
		pinctrl-1 = <&cam_sensor_mclk3_suspend
				 &cam_sensor_front_iris_suspend>;
		gpios = <&tlmm 35 0>,
			<&tlmm 52 0>;
		qcom,gpio-reset = <1>;
		qcom,gpio-req-tbl-num = <0 1>;
		qcom,gpio-req-tbl-flags = <1 0>;
		qcom,gpio-req-tbl-label = "CAMIF_MCLK3",
					"CAM_RESET3";
		qcom,sensor-position = <1>;
		qcom,sensor-mode = <0>;
		qcom,cci-master = <1>;
		clocks = <&clock_mmss MCLK3_CLK_SRC>,
			<&clock_mmss MMSS_CAMSS_MCLK3_CLK>;
		clock-names = "cam_src_clk", "cam_clk";
		qcom,clock-rates = <24000000 0>;
	};
};

&pm660l_gpios {
	cam_sensor_eldo3 {
		cam_sensor_eldo3_default: cam_sensor_eldo3_default {
			pins = "gpio3";
			function = "normal";
			output-high;
			bias-disable;
		};
	};
	cam_sensor_eldo4 {
		cam_sensor_eldo4_default: cam_sensor_eldo4_default {
			pins = "gpio4";
			function = "normal";
			output-low;
			bias-disable;
		};
	};
};