1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
|
&soc {
timer {
clock-frequency = <500000>;
};
timer@17c20000 {
clock-frequency = <500000>;
};
usb_emu_phy: usb_emu_phy@a720000 {
compatible = "qcom,usb-emu-phy";
reg = <0x0a720000 0x9500>,
<0x0a6f8800 0x100>;
reg-names = "base", "qscratch_base";
qcom,emu-init-seq = <0xfff0 0x4
0xfff3 0x4
0x40 0x4
0xfff3 0x4
0xfff0 0x4
0x100000 0x20
0x0 0x20
0x1a0 0x20
0x100000 0x3c
0x0 0x3c
0x10060 0x3c
0x0 0x4>;
};
cxo: bi_tcxo {
compatible = "fixed-factor-clock";
clocks = <&xo_board>;
clock-mult = <1>;
clock-div = <2>;
#clock-cells = <0>;
};
cxo_a: bi_tcxo_ao {
compatible = "fixed-factor-clock";
clocks = <&xo_board>;
clock-mult = <1>;
clock-div = <2>;
#clock-cells = <0>;
};
};
&rpmhcc {
compatible = "qcom,dummycc";
clock-output-names = "rpmh_clocks";
};
&aopcc {
compatible = "qcom,dummycc";
clock-output-names = "qdss_clocks";
};
&usb0 {
dwc3@a600000 {
usb-phy = <&usb_emu_phy>, <&usb_nop_phy>;
maximum-speed = "high-speed";
};
};
&usb2_phy0 {
hsphy@88e3000 {
status = "disabled";
};
};
&qupv3_se8_2uart {
status = "disabled";
};
/*RUMI UART console*/
&qupv3_se2_2uart {
status = "ok";
};
&wdog {
status = "disabled";
};
&ufsphy_mem {
compatible = "qcom,ufs-phy-qrbtc-sdm845";
vdda-phy-supply = <&pm8150_l5>;
vdda-pll-supply = <&pm8150_l6>;
vdda-phy-max-microamp = <90200>;
vdda-pll-max-microamp = <19000>;
status = "ok";
};
&ufshc_mem {
limit-tx-hs-gear = <1>;
limit-rx-hs-gear = <1>;
vdd-hba-supply = <&ufs_phy_gdsc>;
vdd-hba-fixed-regulator;
vcc-supply = <&pm8150a_l7>;
vccq2-supply = <&pm8150_s4>;
vcc-max-microamp = <800000>;
vccq2-max-microamp = <800000>;
qcom,vddp-ref-clk-supply = <&pm8150_l6>;
qcom,vddp-ref-clk-max-microamp = <100>;
qcom,disable-lpm;
rpm-level = <0>;
spm-level = <0>;
status = "ok";
};
&sdhc_1 {
vdd-supply = <&pm8150a_l7>;
qcom,vdd-voltage-level = <2950000 2950000>;
qcom,vdd-current-level = <0 570000>;
vdd-io-supply = <&pm8150_s4>;
qcom,vdd-io-always-on;
qcom,vdd-io-lpm-sup;
qcom,vdd-io-voltage-level = <1800000 1800000>;
qcom,vdd-io-current-level = <0 325000>;
pinctrl-names = "active", "sleep";
pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on
&sdc1_rclk_on>;
pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off
&sdc1_rclk_off>;
qcom,clk-rates = <400000 20000000 25000000 50000000>;
qcom,bus-speed-mode = "DDR_1p8v";
/delete-property/qcom,devfreq,freq-table;
status = "ok";
};
&sdhc_2 {
vdd-supply = <&pm8150a_l9>;
qcom,vdd-voltage-level = <2950000 2950000>;
qcom,vdd-current-level = <0 800000>;
vdd-io-supply = <&pm8150a_l6>;
qcom,vdd-io-voltage-level = <1800000 2950000>;
qcom,vdd-io-current-level = <0 22000>;
pinctrl-names = "active", "sleep";
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
qcom,clk-rates = <400000 20000000 25000000 50000000>;
qcom,bus-speed-mode = "SDR12", "SDR25", "SDR50";
/delete-property/qcom,devfreq,freq-table;
status = "ok";
};
&qupv3_se9_i2c {
status = "disabled";
};
|
