1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
|
/*
* Copyright (C) 2008 The Android Open Source Project
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*/
#include "bootloader.h"
#include "common.h"
#include "firmware.h"
#include "mtdutils/mtdutils.h"
#include <errno.h>
#include <string.h>
#include <sys/reboot.h>
/* Bootloader / Recovery Flow
*
* On every boot, the bootloader will read the bootloader_message
* from flash and check the command field. The bootloader should
* deal with the command field not having a 0 terminator correctly
* (so as to not crash if the block is invalid or corrupt).
*
* The bootloader will have to publish the partition that contains
* the bootloader_message to the linux kernel so it can update it.
*
* if command == "boot-recovery" -> boot recovery.img
* else if command == "update-radio" -> update radio image (below)
* else if command == "update-hboot" -> update hboot image (below)
* else -> boot boot.img (normal boot)
*
* Radio/Hboot Update Flow
* 1. the bootloader will attempt to load and validate the header
* 2. if the header is invalid, status="invalid-update", goto #8
* 3. display the busy image on-screen
* 4. if the update image is invalid, status="invalid-radio-image", goto #8
* 5. attempt to update the firmware (depending on the command)
* 6. if successful, status="okay", goto #8
* 7. if failed, and the old image can still boot, status="failed-update"
* 8. write the bootloader_message, leaving the recovery field
* unchanged, updating status, and setting command to
* "boot-recovery"
* 9. reboot
*
* The bootloader will not modify or erase the cache partition.
* It is recovery's responsibility to clean up the mess afterwards.
*/
#undef LOGE
#define LOGE(...) fprintf(stderr, "E:" __VA_ARGS__)
int install_firmware_update(const char *update_type,
const char *update_data,
size_t update_length,
int width, int height, int bpp,
const char* busy_image,
const char* fail_image,
const char *log_filename) {
if (update_data == NULL || update_length == 0) return 0;
mtd_scan_partitions();
/* We destroy the cache partition to pass the update image to the
* bootloader, so all we can really do afterwards is wipe cache and reboot.
* Set up this instruction now, in case we're interrupted while writing.
*/
struct bootloader_message boot;
memset(&boot, 0, sizeof(boot));
strlcpy(boot.command, "boot-recovery", sizeof(boot.command));
strlcpy(boot.recovery, "recovery\n--wipe_cache\n", sizeof(boot.command));
if (set_bootloader_message(&boot)) return -1;
if (write_update_for_bootloader(
update_data, update_length,
width, height, bpp, busy_image, fail_image, log_filename)) {
LOGE("Can't write %s image\n(%s)\n", update_type, strerror(errno));
return -1;
}
/* The update image is fully written, so now we can instruct the bootloader
* to install it. (After doing so, it will come back here, and we will
* wipe the cache and reboot into the system.)
*/
snprintf(boot.command, sizeof(boot.command), "update-%s", update_type);
if (set_bootloader_message(&boot)) {
return -1;
}
reboot(RB_AUTOBOOT);
// Can't reboot? WTF?
LOGE("Can't reboot\n");
return -1;
}
|
