1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
|
/** @file
*
* Copyright (c) 2011, ARM Limited. All rights reserved.
*
* This program and the accompanying materials
* are licensed and made available under the terms and conditions of the BSD License
* which accompanies this distribution. The full text of the license may be found at
* http://opensource.org/licenses/bsd-license.php
*
* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
*
**/
#include <Library/IoLib.h>
#include <Library/ArmTrustZoneLib.h>
#include <Library/ArmPlatformLib.h>
#include <Library/DebugLib.h>
#include <Library/PcdLib.h>
#include <Library/SerialPortLib.h>
#include <Drivers/PL341Dmc.h>
#include <Drivers/PL301Axi.h>
#include <Drivers/SP804Timer.h>
#include <ArmPlatform.h>
#define SerialPrint(txt) SerialPortWrite ((UINT8*)(txt), AsciiStrLen(txt)+1);
// DDR2 timings
PL341_DMC_CONFIG DDRTimings = {
.MaxChip = 1,
.IsUserCfg = TRUE,
.User0Cfg = 0x7C924924,
.User2Cfg = (TC_UIOLHXC_VALUE << TC_UIOLHNC_SHIFT) | (TC_UIOLHXC_VALUE << TC_UIOLHPC_SHIFT) | (0x1 << TC_UIOHOCT_SHIFT) | (0x1 << TC_UIOHSTOP_SHIFT),
.HasQos = TRUE,
.RefreshPeriod = 0x3D0,
.CasLatency = 0x8,
.WriteLatency = 0x3,
.t_mrd = 0x2,
.t_ras = 0xA,
.t_rc = 0xE,
.t_rcd = 0x104,
.t_rfc = 0x2f32,
.t_rp = 0x14,
.t_rrd = 0x2,
.t_wr = 0x4,
.t_wtr = 0x2,
.t_xp = 0x2,
.t_xsr = 0xC8,
.t_esr = 0x14,
.MemoryCfg = DMC_MEMORY_CONFIG_ACTIVE_CHIP_1 | DMC_MEMORY_CONFIG_BURST_4 |
DMC_MEMORY_CONFIG_ROW_ADDRESS_15 | DMC_MEMORY_CONFIG_COLUMN_ADDRESS_10,
.MemoryCfg2 = DMC_MEMORY_CFG2_DQM_INIT | DMC_MEMORY_CFG2_CKE_INIT |
DMC_MEMORY_CFG2_BANK_BITS_3 | DMC_MEMORY_CFG2_MEM_WIDTH_32,
.MemoryCfg3 = 0x00000001,
.ChipCfg0 = 0x00010000,
.t_faw = 0x00000A0D,
.ModeReg = DDR2_MR_BURST_LENGTH_4 | DDR2_MR_CAS_LATENCY_4 | DDR2_MR_WR_CYCLES_4,
.ExtModeReg = DDR_EMR_RTT_50R | (DDR_EMR_ODS_VAL << DDR_EMR_ODS_MASK),
};
/**
Return if Trustzone is supported by your platform
A non-zero value must be returned if you want to support a Secure World on your platform.
ArmVExpressTrustzoneInit() will later set up the secure regions.
This function can return 0 even if Trustzone is supported by your processor. In this case,
the platform will continue to run in Secure World.
@return A non-zero value if Trustzone supported.
**/
UINTN
ArmPlatformTrustzoneSupported (
VOID
)
{
return (MmioRead32(ARM_VE_SYS_CFGRW1_REG) & ARM_VE_CFGRW1_TZASC_EN_BIT_MASK);
}
/**
Return the current Boot Mode
This function returns the boot reason on the platform
@return Return the current Boot Mode of the platform
**/
EFI_BOOT_MODE
ArmPlatformGetBootMode (
VOID
)
{
return BOOT_WITH_FULL_CONFIGURATION;
}
/**
Remap the memory at 0x0
Some platform requires or gives the ability to remap the memory at the address 0x0.
This function can do nothing if this feature is not relevant to your platform.
**/
VOID
ArmPlatformBootRemapping (
VOID
)
{
UINT32 Value;
if (FeaturePcdGet(PcdNorFlashRemapping)) {
SerialPrint ("Secure ROM at 0x0\n\r");
} else {
Value = MmioRead32(ARM_VE_SYS_CFGRW1_REG); //Scc - CFGRW1
// Remap the DRAM to 0x0
MmioWrite32(ARM_VE_SYS_CFGRW1_REG, (Value & 0x0FFFFFFF) | ARM_VE_CFGRW1_REMAP_DRAM);
}
}
/**
Initialize controllers that must setup in the normal world
This function is called by the ArmPlatformPkg/PrePi or ArmPlatformPkg/PlatformPei
in the PEI phase.
**/
VOID
ArmPlatformNormalInitialize (
VOID
)
{
// Configure periodic timer (TIMER0) for 1MHz operation
MmioOr32 (SP810_CTRL_BASE + SP810_SYS_CTRL_REG, SP810_SYS_CTRL_TIMER0_TIMCLK);
// Configure 1MHz clock
MmioOr32 (SP810_CTRL_BASE + SP810_SYS_CTRL_REG, SP810_SYS_CTRL_TIMER1_TIMCLK);
// configure SP810 to use 1MHz clock and disable
MmioAndThenOr32 (SP810_CTRL_BASE + SP810_SYS_CTRL_REG, ~SP810_SYS_CTRL_TIMER2_EN, SP810_SYS_CTRL_TIMER2_TIMCLK);
// Configure SP810 to use 1MHz clock and disable
MmioAndThenOr32 (SP810_CTRL_BASE + SP810_SYS_CTRL_REG, ~SP810_SYS_CTRL_TIMER3_EN, SP810_SYS_CTRL_TIMER3_TIMCLK);
}
/**
Initialize the system (or sometimes called permanent) memory
This memory is generally represented by the DRAM.
**/
VOID
ArmPlatformInitializeSystemMemory (
VOID
)
{
PL341DmcInit(ARM_VE_DMC_BASE, &DDRTimings);
PL301AxiInit(ARM_VE_FAXI_BASE);
}
VOID
ArmPlatformGetPlatformPpiList (
OUT UINTN *PpiListSize,
OUT EFI_PEI_PPI_DESCRIPTOR **PpiList
)
{
*PpiListSize = 0;
*PpiList = NULL;
}
|
