ARM: dts: camera: Add support for camera hardware for Kona platforms

Add support for camera for kona platforms as a part of new project.

Change-Id: I3ceaa513b9bfb5cfac0f9baf1f905c8eed492e6b

1 files changed, 638 insertions, 0 deletions

diff --git a/kona-camera-sensor-cdp.dtsi b/kona-camera-sensor-cdp.dtsi
new file mode 100644
index 0000000..a81bb8f
--- /dev/null
+++ b/kona-camera-sensor-cdp.dtsi
@@ -0,0 +1,638 @@
+#include <dt-bindings/clock/qcom,camcc-kona.h>
+
+&soc {
+	led_flash_rear: qcom,camera-flash0 {
+		cell-index = <0>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux: qcom,camera-flash1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear: qcom,camera-flash@4 {
+		cell-index = <4>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@5 {
+		cell-index = <5>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@6 {
+		cell-index = <6>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_rear_aux: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_triple_wide: qcom,actuator4 {
+		cell-index = <4>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_triple_tele: qcom,actuator5 {
+		cell-index = <5>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_triple_uw: qcom,actuator6 {
+		cell-index = <6>;
+		compatible = "qcom,actuator";
+		cci-master = <1>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	eeprom_rear: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <0 2800000 1104000 0 2856000>;
+		rgltr-max-voltage = <0 3000000 1104000 0 3104000>;
+		rgltr-load-current = <0 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <0 2800000 1200000 0 2856000>;
+		rgltr-max-voltage = <0 3000000 1200000 0 3104000>;
+		rgltr-load-current = <0 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_wide: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <0 2800000 1104000 0 2856000>;
+		rgltr-max-voltage = <0 3000000 1104000 0 3104000>;
+		rgltr-load-current = <0 80000 1200000 0 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_tele: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <0 2800000 1200000 0 2856000>;
+		rgltr-max-voltage = <0 3000000 1200000 0 3104000>;
+		rgltr-load-current = <0 80000 1200000 0 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_uw: qcom,eeprom6 {
+		cell-index = <6>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <0 2800000 1056000 0 2856000>;
+		rgltr-max-voltage = <0 3000000 1056000 0 3104000>;
+		rgltr-load-current = <0 80000 1200000 0 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear>;
+		led-flash-src = <&led_flash_rear>;
+		eeprom-src = <&eeprom_rear>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <0 2800000 1104000 0 3008000>;
+		rgltr-max-voltage = <0 3000000 1104000 0 3960000>;
+		rgltr-load-current = <0 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_rear_aux>;
+		led-flash-src = <&led_flash_rear_aux>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <0 2800000 1200000 0 3008000>;
+		rgltr-max-voltage = <0 3000000 1200000 0 3960000>;
+		rgltr-load-current = <0 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear>;
+		eeprom-src = <&eeprom_triple_wide>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <0 2800000 1104000 0 3008000>;
+		rgltr-max-voltage = <0 3000000 1104000 0 3960000>;
+		rgltr-load-current = <0 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <0 2800000 1200000 0 3008000>;
+		rgltr-max-voltage = <0 3000000 1200000 0 3960000>;
+		rgltr-load-current = <0 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor6 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <0 2800000 1056000 0 3008000>;
+		rgltr-max-voltage = <0 3000000 1056000 0 3960000>;
+		rgltr-load-current = <0 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+	eeprom_front: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <0 2800000 1056000 0 2856000>;
+		rgltr-max-voltage = <0 3000000 1056000 0 3104000>;
+		rgltr-load-current = <0 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <0 2800000 1056000 0 3008000>;
+		rgltr-max-voltage = <0 3000000 1056000 0 3960000>;
+		rgltr-load-current = <0 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vdig-supply = <&vreg_tof>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <0 3600000 0>;
+		rgltr-max-voltage = <0 3600000 0>;
+		rgltr-load-current = <180000 120000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_3>;
+		gpios = <&tlmm 97 0>,
+			<&tlmm 109 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};