1 files changed, 122 insertions, 0 deletions
diff --git a/include/drivers/nxp/flexspi/fspi_api.h b/include/drivers/nxp/flexspi/fspi_api.h
new file mode 100644
index 000000000..d0de5432f
--- /dev/null
+++ b/include/drivers/nxp/flexspi/fspi_api.h
@@ -0,0 +1,122 @@
+/*
+ * Copyright 2021 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ *
+ */
+
+
+/*!
+ * @file	fspi_api.h
+ * @brief	This file contains the FlexSPI/FSPI API to communicate
+ *		to attached Slave device.
+ * @addtogroup	FSPI_API
+ * @{
+ */
+
+#ifndef FSPI_API_H
+#define FSPI_API_H
+
+#if DEBUG_FLEXSPI
+#define SZ_57M			0x3900000u
+#endif
+
+/*!
+ * Basic set of APIs.
+ */
+
+/*!
+ * @details AHB read/IP Read, decision to be internal to API
+ * Minimum Read size = 1Byte
+ * @param[in] src_off source offset from where data to read from flash
+ * @param[out] des Destination location where data needs to be copied
+ * @param[in] len length in Bytes,where 1-word=4-bytes/32-bits
+ *
+ * @return XSPI_SUCCESS or error code
+ */
+int xspi_read(uint32_t src_off, uint32_t *des, uint32_t len);
+/*!
+ * @details Sector erase, Minimum size
+ * 256KB(0x40000)/128KB(0x20000)/64K(0x10000)/4K(0x1000)
+ * depending upon flash, Calls xspi_wren() internally
+ * @param[out] erase_offset Destination erase location on flash which
+ * has to be erased, needs to be multiple of 0x40000/0x20000/0x10000
+ * @param[in] erase_len length in bytes in Hex like 0x100000 for 1MB, minimum
+ * erase size is 1 sector(0x40000/0x20000/0x10000)
+ *
+ * @return XSPI_SUCCESS or error code
+ */
+int xspi_sector_erase(uint32_t erase_offset, uint32_t erase_len);
+/*!
+ * @details IP write, For writing data to flash, calls xspi_wren() internally.
+ * Single/multiple page write can start @any offset, but performance will be low
+ * due to ERRATA
+ * @param[out] dst_off Destination location on flash where data needs to
+ * be written
+ * @param[in] src source offset from where data to be read
+ * @param[in] len length in bytes,where 1-word=4-bytes/32-bits
+ *
+ * @return XSPI_SUCCESS or error code
+ */
+int xspi_write(uint32_t dst_off, void *src, uint32_t len);
+/*!
+ * @details fspi_init, Init function.
+ * @param[in] uint32_t base_reg_addr
+ * @param[in] uint32_t flash_start_addr
+ *
+ * @return XSPI_SUCCESS or error code
+ */
+int fspi_init(uint32_t base_reg_addr, uint32_t flash_start_addr);
+/*!
+ * @details is_flash_busy, Check if any erase or write or lock is
+ * pending on flash/slave
+ * @param[in] void
+ *
+ * @return TRUE/FLASE
+ */
+bool is_flash_busy(void);
+
+/*!
+ * Advanced set of APIs.
+ */
+
+/*!
+ * @details Write enable, to be used by advance users only.
+ * Step 1 for sending write commands to flash.
+ * @param[in] dst_off destination offset where data will be written
+ *
+ * @return XSPI_SUCCESS or error code
+ */
+int xspi_wren(uint32_t dst_off);
+/*!
+ * @details AHB read, meaning direct memory mapped access to flash,
+ * Minimum Read size = 1Byte
+ * @param[in] src_off source offset from where data to read from flash,
+ * needs to be word aligned
+ * @param[out] des Destination location where data needs to be copied
+ * @param[in] len length in Bytes,where 1-word=4-bytes/32-bits
+ *
+ * @return XSPI_SUCCESS or error code
+ */
+int xspi_ahb_read(uint32_t src_off, uint32_t *des, uint32_t len);
+/*!
+ * @details IP read, READ via RX buffer from flash, minimum READ size = 1Byte
+ * @param[in] src_off source offset from where data to be read from flash
+ * @param[out] des Destination location where data needs to be copied
+ * @param[in] len length in Bytes,where 1-word=4-bytes/32-bits
+ *
+ * @return XSPI_SUCCESS or error code
+ */
+int xspi_ip_read(uint32_t src_off, uint32_t *des, uint32_t len);
+/*!
+ * @details CHIP erase, Erase complete chip in one go
+ *
+ * @return XSPI_SUCCESS or error code
+ */
+int xspi_bulk_erase(void);
+
+/*!
+ * Add test cases to confirm flash read/erase/write functionality.
+ */
+void fspi_test(uint32_t fspi_test_addr, uint32_t size, int extra);
+#endif /* FSPI_API_H */