1 files changed, 25 insertions, 24 deletions

diff --git a/arch/arm/mach-k3/am625_init.c b/arch/arm/mach-k3/am625_init.c
index 0e5d44269e..8fa36f7b91 100644
--- a/arch/arm/mach-k3/am625_init.c
+++ b/arch/arm/mach-k3/am625_init.c
@@ -80,8 +80,6 @@ static __maybe_unused void enable_mcu_esm_reset(void)
 	writel(stat, CTRLMMR_MCU_RST_CTRL);
 }
 
-#if defined(CONFIG_CPU_V7R)
-
 /*
  * RTC Erratum i2327 Workaround for Silicon Revision 1
  *
@@ -94,7 +92,7 @@ static __maybe_unused void enable_mcu_esm_reset(void)
  *
  * https://www.ti.com/lit/er/sprz487c/sprz487c.pdf
  */
-void rtc_erratumi2327_init(void)
+static __maybe_unused void rtc_erratumi2327_init(void)
 {
 	u32 counter;
 
@@ -112,19 +110,17 @@ void rtc_erratumi2327_init(void)
 	 */
 	writel(K3RTC_KICK0_UNLOCK_VALUE, REG_K3RTC_KICK0);
 	writel(K3RTC_KICK1_UNLOCK_VALUE, REG_K3RTC_KICK1);
-	return;
 }
-#endif
 
 void board_init_f(ulong dummy)
 {
 	struct udevice *dev;
 	int ret;
 
-#if defined(CONFIG_CPU_V7R)
-	setup_k3_mpu_regions();
-	rtc_erratumi2327_init();
-#endif
+	if (IS_ENABLED(CONFIG_CPU_V7R)) {
+		setup_k3_mpu_regions();
+		rtc_erratumi2327_init();
+	}
 
 	/*
 	 * Cannot delay this further as there is a chance that
@@ -156,29 +152,28 @@ void board_init_f(ulong dummy)
 
 	preloader_console_init();
 
-#ifdef CONFIG_K3_EARLY_CONS
 	/*
 	 * Allow establishing an early console as required for example when
 	 * doing a UART-based boot. Note that this console may not "survive"
 	 * through a SYSFW PM-init step and will need a re-init in some way
 	 * due to changing module clock frequencies.
 	 */
-	early_console_init();
-#endif
+	if (IS_ENABLED(CONFIG_K3_EARLY_CONS))
+		early_console_init();
 
-#if defined(CONFIG_K3_LOAD_SYSFW)
 	/*
 	 * Configure and start up system controller firmware. Provide
 	 * the U-Boot console init function to the SYSFW post-PM configuration
 	 * callback hook, effectively switching on (or over) the console
 	 * output.
 	 */
-	ret = is_rom_loaded_sysfw(&bootdata);
-	if (!ret)
-		panic("ROM has not loaded TIFS firmware\n");
+	if (IS_ENABLED(CONFIG_K3_LOAD_SYSFW)) {
+		ret = is_rom_loaded_sysfw(&bootdata);
+		if (!ret)
+			panic("ROM has not loaded TIFS firmware\n");
 
-	k3_sysfw_loader(true, NULL, NULL);
-#endif
+		k3_sysfw_loader(true, NULL, NULL);
+	}
 
 	/*
 	 * Force probe of clk_k3 driver here to ensure basic default clock
@@ -209,11 +204,11 @@ void board_init_f(ulong dummy)
 		enable_mcu_esm_reset();
 	}
 
-#if defined(CONFIG_K3_AM64_DDRSS)
-	ret = uclass_get_device(UCLASS_RAM, 0, &dev);
-	if (ret)
-		panic("DRAM init failed: %d\n", ret);
-#endif
+	if (IS_ENABLED(CONFIG_K3_AM64_DDRSS)) {
+		ret = uclass_get_device(UCLASS_RAM, 0, &dev);
+		if (ret)
+			panic("DRAM init failed: %d\n", ret);
+	}
 	spl_enable_dcache();
 }
 
@@ -225,9 +220,15 @@ u32 spl_mmc_boot_mode(struct mmc *mmc, const u32 boot_device)
 	u32 bootmode_cfg = (devstat & MAIN_DEVSTAT_PRIMARY_BOOTMODE_CFG_MASK) >>
 			    MAIN_DEVSTAT_PRIMARY_BOOTMODE_CFG_SHIFT;
 
-
 	switch (bootmode) {
 	case BOOT_DEVICE_EMMC:
+		if (IS_ENABLED(CONFIG_SUPPORT_EMMC_BOOT)) {
+			if (spl_mmc_emmc_boot_partition(mmc))
+				return MMCSD_MODE_EMMCBOOT;
+			return MMCSD_MODE_FS;
+		}
+		if (IS_ENABLED(CONFIG_SPL_FS_FAT) || IS_ENABLED(CONFIG_SPL_FS_EXT4))
+			return MMCSD_MODE_FS;
 		return MMCSD_MODE_EMMCBOOT;
 	case BOOT_DEVICE_MMC:
 		if (bootmode_cfg & MAIN_DEVSTAT_PRIMARY_MMC_FS_RAW_MASK)