path: root/drivers/power/pmic/Kconfig

config DM_PMIC
	bool "Enable Driver Model for PMIC drivers (UCLASS_PMIC)"
	depends on DM
	---help---
	This config enables the driver-model PMIC support.
	UCLASS_PMIC - designed to provide an I/O interface for PMIC devices.
	For the multi-function PMIC devices, this can be used as parent I/O
	device for each IC's interface. Then, each children uses its parent
	for read/write. For detailed description, please refer to the files:
	- 'drivers/power/pmic/pmic-uclass.c'
	- 'include/power/pmic.h'

if DM_PMIC

config SPL_DM_PMIC
	bool "Enable Driver Model for PMIC drivers (UCLASS_PMIC) in SPL"
	depends on SPL_DM
	default y
	---help---
	This config enables the driver-model PMIC support in SPL.
	UCLASS_PMIC - designed to provide an I/O interface for PMIC devices.
	For the multi-function PMIC devices, this can be used as parent I/O
	device for each IC's interface. Then, each children uses its parent
	for read/write. For detailed description, please refer to the files:
	- 'drivers/power/pmic/pmic-uclass.c'
	- 'include/power/pmic.h'

config PMIC_CHILDREN
	bool "Allow child devices for PMICs"
	default y
	---help---
	This allows PMICs to support child devices (such as regulators) in
	SPL. This adds quite a bit of code so if you are not using this
	feature you can turn it off. Most likely you should turn it on for
	U-Boot proper.

config SPL_PMIC_CHILDREN
	bool "Allow child devices for PMICs in SPL"
	depends on SPL_DM_PMIC
	default y
	---help---
	This allows PMICs to support child devices (such as regulators) in
	SPL. This adds quite a bit of code so if you are not using this
	feature you can turn it off. In this case you may need a 'back door'
	to call your regulator code (e.g. see rk8xx.c for direct functions
	for use in SPL).

config PMIC_AB8500
	bool "Enable driver for ST-Ericsson AB8500 PMIC via PRCMU"
	select REGMAP
	select SYSCON
	help
	  Enable support for the ST-Ericsson AB8500 (Analog Baseband) PMIC.
	  It connects with the ST-Ericsson DB8500 SoC via an I2C bus managed by
	  the power/reset/clock management unit (PRCMU) firmware.

config PMIC_ACT8846
	bool "Enable support for the active-semi 8846 PMIC"
	depends on DM_I2C
	---help---
	This PMIC includes 4 DC/DC step-down buck regulators and 8 low-dropout
	regulators (LDOs). It also provides some GPIO, reset and battery
	functions. It uses an I2C interface and is designed for use with
	tablets and smartphones.

config PMIC_AXP
	bool "Enable Driver Model for X-Powers AXP PMICs"
	depends on DM_I2C
	select SYSRESET_CMD_POWEROFF if SYSRESET && CMD_POWEROFF
	imply CMD_POWEROFF if SYSRESET
	help
	  This config enables driver-model PMIC uclass features for
	  X-Powers AXP152, AXP2xx, and AXP8xx PMICs.

config SPL_PMIC_AXP
	bool "Enable Driver Model for X-Powers AXP PMICs in SPL"
	depends on SPL_DM_I2C && SPL_DM_PMIC
	help
	  This config enables driver-model PMIC uclass features in the SPL for
	  X-Powers AXP152, AXP2xx, and AXP8xx PMICs.

config DM_PMIC_DA9063
	bool "Enable Driver Model for the Dialog DA9063 PMIC"
	help
	  This config enables implementation of driver-model pmic uclass features
	  for PMIC DA9063. The driver implements read/write operations.

config SPL_DM_PMIC_DA9063
	bool "Enable Driver Model for the Dialog DA9063 PMIC in SPL"
	depends on SPL_DM_PMIC
	help
	  This config enables implementation of driver-model pmic uclass features
	  for PMIC DA9063. The driver implements read/write operations.

config PMIC_AS3722
	bool "Enable support for the Austria Micro Systems (AMS) AS7322 PMIC"
	help
	  The AS3722 includes 7 DC/DC buck convertors, 11 low-noise LDOs, a
	  real-time clock, GPIOs, ADC and a few other features. It uses an I2C
	  interface and is designs to cover most of the power managementment
	  required for a tablets or laptop.

config DM_PMIC_BD71837
 	bool "Enable Driver Model for PMIC BD71837"
 	help
	  This config enables implementation of driver-model pmic uclass features
	  for PMIC BD71837. The driver implements read/write operations.

config SPL_DM_PMIC_BD71837
	bool "Enable Driver Model for PMIC BD71837 in SPL stage"
	depends on SPL_DM_PMIC
	help
	  This config enables implementation of driver-model pmic uclass
	  features for PMIC BD71837. The driver implements read/write
	  operations.

config DM_PMIC_FAN53555
	bool "Enable support for OnSemi FAN53555"
	depends on DM_REGULATOR && DM_I2C
	select DM_REGULATOR_FAN53555
	help
	  This config enables implementation of driver-model PMIC
	  uclass features for the FAN53555 regulator. The FAN53555 is
	  a (family of) single-output regulators that supports
	  transitioning between two different output voltages based on
	  an voltage selection pin.

	  The driver implements read/write operations for use with the FAN53555
	  regulator driver and binds the regulator driver to its node.

config SPL_DM_PMIC_FAN53555
	bool "Enable support for OnSemi FAN53555 in SPL"
	depends on SPL_DM_REGULATOR && SPL_DM_I2C
	select SPL_DM_REGULATOR_FAN53555
	help
	  This config enables implementation of driver-model PMIC
	  uclass features for the FAN53555 regulator. The FAN53555 is
	  a (family of) single-output regulators that supports
	  transitioning between two different output voltages based on
	  an voltage selection pin.

	  The driver implements read/write operations for use with the FAN53555
	  regulator driver and binds the regulator driver to its node.

config DM_PMIC_MP5416
	bool "Enable Driver Model for PMIC MP5416"
	help
	  This config enables implementation of driver-model pmic uclass features
	  for PMIC MP5416. The driver implements read/write operations.

config SPL_DM_PMIC_MP5416
	bool "Enable Driver Model for PMIC MP5416 in SPL stage"
	depends on SPL_DM_PMIC
	help
	  This config enables implementation of driver-model pmic uclass
	  features for PMIC MP5416. The driver implements read/write
	  operations.

config DM_PMIC_PCA9450
	bool "Enable Driver Model for PMIC PCA9450"
	depends on DM_I2C
	help
	  This config enables implementation of driver-model pmic uclass features
	  for PMIC PCA9450. The driver implements read/write operations.

config SPL_DM_PMIC_PCA9450
	bool "Enable Driver Model for PMIC PCA9450 in SPL"
	depends on SPL_DM_PMIC
	depends on SPL_DM_I2C
	help
	  This config enables implementation of driver-model pmic uclass features
	  for PMIC PCA9450 in SPL. The driver implements read/write operations.

config DM_PMIC_PFUZE100
	bool "Enable Driver Model for PMIC PFUZE100"
	---help---
	This config enables implementation of driver-model pmic uclass features
	for PMIC PFUZE100. The driver implements read/write operations.

config SPL_DM_PMIC_PFUZE100
	bool "Enable Driver Model for PMIC PFUZE100 in SPL"
	depends on SPL_DM_PMIC
	---help---
	This config enables implementation of driver-model pmic uclass features
	for PMIC PFUZE100 in SPL. The driver implements read/write operations.

config DM_PMIC_MAX77686
	bool "Enable Driver Model for PMIC MAX77686"
	---help---
	This config enables implementation of driver-model pmic uclass features
	for PMIC MAX77686. The driver implements read/write operations.

config DM_PMIC_MAX8998
	bool "Enable Driver Model for PMIC MAX8998"
	---help---
	This config enables implementation of driver-model pmic uclass features
	for PMIC MAX8998. The driver implements read/write operations.

config DM_PMIC_MC34708
	bool "Enable Driver Model for PMIC MC34708"
	help
	 This config enables implementation of driver-model pmic uclass features
	 for PMIC MC34708. The driver implements read/write operations.

config PMIC_MAX8997
	bool "Enable Driver Model for PMIC MAX8997"
	---help---
	This config enables implementation of driver-model pmic uclass features
	for PMIC MAX8997. The driver implements read/write operations.
	This is a Power Management IC with RTC, Fuel Gauge, MUIC control on Chip.
	- 21x LDOs
	- 12x GPIOs
	- Haptic Motor driver
	- RTC with two alarms
	- Fueal Gauge and One backup battery charger
	- MUIC
	- Others

config PMIC_QCOM
	bool "Enable Driver Model for Qualcomm generic PMIC"
	---help---
	The Qcom PMIC is connected to one (or several) processors
	with SPMI bus. It has 2 slaves with several peripherals:
	- 18x LDO
	- 4x GPIO
	- Power and Reset buttons
	- Watchdog
	- RTC
	- Vibrator drivers
	- Others

	Driver binding info: doc/device-tree-bindings/pmic/qcom,spmi-pmic.txt

config PMIC_RK8XX
	bool "Enable support for Rockchip PMIC RK8XX"
	---help---
	The Rockchip RK808 PMIC provides four buck DC-DC convertors, 8 LDOs,
	an RTC and two low Rds (resistance (drain to source)) switches. It is
	accessed via an I2C interface. The device is used with Rockchip SoCs.
	This driver implements register read/write operations.

config SPL_PMIC_RK8XX
	bool "Enable support for Rockchip PMIC RK8XX"
	depends on SPL_DM_PMIC
	---help---
	The Rockchip RK808 PMIC provides four buck DC-DC convertors, 8 LDOs,
	an RTC and two low Rds (resistance (drain to source)) switches. It is
	accessed via an I2C interface. The device is used with Rockchip SoCs.
	This driver implements register read/write operations.

config PMIC_S2MPS11
	bool "Enable Driver Model for PMIC Samsung S2MPS11"
	---help---
	The Samsung S2MPS11 PMIC provides:
	 - 38 adjustable LDO regulators
	 - 9 High-Efficiency Buck Converters
	 - 1 BuckBoost Converter
	 - RTC with two alarms
	 - Backup battery charger
	 - I2C Configuration Interface
	This driver provides access to I/O interface only.
	Binding info: doc/device-tree-bindings/pmic/s2mps11.txt

config DM_PMIC_SANDBOX
	bool "Enable Driver Model for emulated Sandbox PMIC"
	---help---
	Enable the driver for Sandbox PMIC emulation. The emulated PMIC device
	depends on two drivers:
	- sandbox PMIC I/O driver - implements dm pmic operations
	- sandbox PMIC i2c emul driver - emulates the PMIC's I2C transmission

	A detailed information can be found in header: '<power/sandbox_pmic.h>'

	The Sandbox PMIC info:
	* I/O interface:
	  - I2C chip address:       0x40
	  - first register address: 0x0
	  - register count:         0x10
	* Adjustable outputs:
	  - 2x LDO
	  - 2x BUCK
	  - Each, with a different operating conditions (header).
	* Reset values:
	  - set by i2c emul driver's probe() (defaults in header)

	Driver binding info: doc/device-tree-bindings/pmic/sandbox.txt

config PMIC_S5M8767
	bool "Enable Driver Model for the Samsung S5M8767 PMIC"
	---help---
	The S5M8767 PMIC provides a large array of LDOs and BUCKs for use
	as a SoC power controller. It also provides 32KHz clock outputs. This
	driver provides basic register access and sets up the attached
	regulators if regulator support is enabled.

config PMIC_RN5T567
	bool "Enable driver for Ricoh RN5T567 PMIC"
	---help---
	The RN5T567 is a PMIC with 4 step-down DC/DC converters, 5 LDO
	regulators Real-Time Clock and 4 GPIOs. This driver provides
	register access only.

config SPL_PMIC_RN5T567
	bool "Enable driver for Ricoh RN5T567 PMIC in SPL"
	depends on SPL_DM_PMIC
	---help---
	The RN5T567 is a PMIC with 4 step-down DC/DC converters, 5 LDO
	regulators Real-Time Clock and 4 GPIOs. This driver provides
	register access only.

config PMIC_TPS65090
	bool "Enable driver for Texas Instruments TPS65090 PMIC"
	---help---
	The TPS65090 is a PMIC containing several LDOs, DC to DC convertors,
	FETs and a battery charger. This driver provides register access
	only, and you can enable the regulator/charger drivers separately if
	required.

config PMIC_PALMAS
	bool "Enable driver for Texas Instruments PALMAS PMIC"
	---help---
	The PALMAS is a PMIC containing several LDOs, SMPS.
	This driver binds the pmic children.

config PMIC_LP873X
	bool "Enable driver for Texas Instruments LP873X PMIC"
	---help---
	The LP873X is a PMIC containing couple of LDOs and couple of SMPS.
	This driver binds the pmic children.

config PMIC_LP87565
	bool "Enable driver for Texas Instruments LP87565 PMIC"
	---help---
	The LP87565 is a PMIC containing a bunch of SMPS.
	This driver binds the pmic children.

config DM_PMIC_TPS65910
	bool "Enable driver for Texas Instruments TPS65910 PMIC"
	---help---
	The TPS65910 is a PMIC containing 3 buck DC-DC converters, one boost
	DC-DC converter, 8 LDOs and a RTC. This driver binds the SMPS and LDO
	pmic children.

config PMIC_STPMIC1
	bool "Enable support for STMicroelectronics STPMIC1 PMIC"
	depends on DM_I2C
	select SYSRESET_CMD_POWEROFF if CMD_POWEROFF && !ARM_PSCI_FW
	---help---
	The STPMIC1 PMIC provides 4 BUCKs, 6 LDOs, 1 VREF and 2 power switches.
	It is accessed via an I2C interface. The device is used with STM32MP1
	SoCs. This driver implements register read/write operations.

config SPL_PMIC_PALMAS
	bool "Enable driver for Texas Instruments PALMAS PMIC"
	depends on SPL_DM_PMIC
	help
	The PALMAS is a PMIC containing several LDOs, SMPS.
	This driver binds the pmic children in SPL.

config SPL_PMIC_LP873X
	bool "Enable driver for Texas Instruments LP873X PMIC"
	depends on SPL_DM_PMIC
	help
	The LP873X is a PMIC containing couple of LDOs and couple of SMPS.
	This driver binds the pmic children in SPL.

config SPL_PMIC_LP87565
	bool "Enable driver for Texas Instruments LP87565 PMIC"
	depends on SPL_DM_PMIC
	help
	The LP87565 is a PMIC containing a bunch of SMPS.
	This driver binds the pmic children in SPL.

config PMIC_TPS65941
	bool "Enable driver for Texas Instruments TPS65941 PMIC"
	help
	The TPS65941 is a PMIC containing a bunch of SMPS & LDOs.
	This driver binds the pmic children.

config PMIC_TPS65219
	bool "Enable driver for Texas Instruments TPS65219 PMIC"
	depends on DM_PMIC
	help
	The TPS65219 is a PMIC containing a bunch of SMPS & LDOs.
	This driver binds the pmic children.
endif

config PMIC_TPS65217
	bool "Enable driver for Texas Instruments TPS65217 PMIC"
	---help---
	The TPS65217 is a PMIC containing several LDOs, DC to DC convertors,
	FETs and a battery charger. This driver provides register access
	only, and you can enable the regulator/charger drivers separately if
	required.

config POWER_TPS65218
	bool "Enable legacy driver for TPS65218 PMIC"

config POWER_TPS62362
	bool "Enable legacy driver for TPS62362 PMIC"

config SPL_POWER_TPS62362
	bool "Enable legacy driver for TPS62362 PMIC in SPL"
	default y if POWER_TPS62362
	depends on SPL

config SPL_POWER_TPS65910
	bool "Enable legacy driver for TPS65910 PMIC in SPL"
	depends on SPL

if POWER_LEGACY || SPL_POWER_LEGACY

config POWER_HI6553
	bool "Enable legacy driver for HI6553 PMIC"

config POWER_LTC3676
	bool "Enable legacy driver for LTC3676 PMIC"

config POWER_PCA9450
	bool "Enable legacy driver for PCA9450 PMIC"

config POWER_PFUZE100
	bool "Enable legacy driver for PFUZE100 PMIC"

config POWER_PFUZE3000
	bool "Enable legacy driver for PFUZE3000 PMIC"

config POWER_MC34VR500
	bool "Enable driver for Freescale MC34VR500 PMIC"
	---help---
	The MC34VR500 is used in conjunction with the FSL T1 and LS1 series
	SoC. It provides 4 buck DC-DC convertors and 5 LDOs, and it is accessed
	via an I2C interface.

endif