1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
|
EEPROMlessModeSupported = 1 # 0 = disable epromless support / 1 = Enable
WME_Enable = 1 # 0 = diable WME support / 1 = Enable
dot11NetworkType = 3 # 2 - A only mode, 3 - B/G mode, 4 - A/G Dual mode
RecoveryEnable = 1 # 0 - Disabled, 1 - Enabled
TriggerFcs = 0 # 0 - Disabled, 1 - Enabled
dot11FragmentationThreshold = 4096
dot11RTSThreshold = 4096
WPAMixedMode = 1
RSNPreAuthentication = 1
CalibrationChannel24 = 1
CalibrationChannel5 = 36
# Regulatury Domain tables.
# Each byte correlates to one channel in sequential order. Table 2.4 starts from channel 1, Table 5.0 starts from channel 36.
# Bits 0..4 - Max power allowed in Dbm.
# Bit 6 - Channel is allowed for Active scan
# BIt 7 - Channel is allowed
AllowedChannelsTable24 = FFFFFFFFFFFFFFFFFFFFFFFFFFFF
AllowedChannelsTable5 = FF000000FF000000FF000000FF000000FF000000FF000000FF000000FF0000000000000000000000000000000000000000000000000000000000000000000000FF000000FF000000FF000000FF000000FF000000FF000000FF000000FF000000FF000000FF000000FF0000000000000000FF000000FF000000FF000000FF00000000000000000000000000000000000000
SpectrumManagement = 0 # 0 - Disable 802.11h, 1 - Enable
RxBroadcastInPs = 1
FirstConnScanEnabled = 1 # 0 - Disable , 1 - Enable
#arp ip filter
ArpIp_Addr = c0 a8 00 5e
ArpIp_Filter_ena = 0
#mac filter
Mac_Filter_Enabled = 0
numGroupAddrs = 4
Group_addr0 = 10 01 02 03 04 05
Group_addr1 = 11 11 12 13 14 15
Group_addr2 = 12 21 22 23 24 25
Group_addr3 = 13 31 32 33 34 35
Group_addr4 = 14 41 42 43 44 45
Group_addr5 = 15 51 52 53 54 55
Group_addr6 = 16 61 62 63 64 65
Group_addr7 = 17 71 72 73 74 75
#beacon filter
Beacon_Filter_Desired_State = 1
Beacon_Filter_Stored = 1
#beacon IE table
#the size is the len of the string - spaces = number of bytes
Beacon_IE_Num_Of_Elem = 15
Beacon_IE_Table_Size = 35
Beacon_IE_Table = 00 01 01 01 32 01 2a 01 03 01 06 01 07 01 20 01 25 01 23 01 30 01 28 01 2e 01 85 01 dd 00 52 f2 02 00 01
#Rate adaptation
RateContThreshold = 10
RateStepUpThreshold = 2
FBShortInterval = 40
FBLongInterval = 200
RateAdaptationTimeout = 300
# rate policy - short / long retries
RatePolicyUserShortRetryLimit = 10
RatePolicyUserLongRetryLimit = 10
#rate policies
RatePolicyUserRetriesPerRateCck = 1,1,1,1,1,1,1,1,1,1,1,1,1
RatePolicyUserRetriesPerRatePbcc = 1,1,1,1,1,1,1,1,1,1,1,1,1
RatePolicyUserRetriesPerRateOfdm = 0,0,0,1,0,0,0,1,0,0,1,1,1
RatePolicyUserRetriesPerRateOfdmA = 0,0,0,1,0,0,1,0,0,1,0,0,0
RatePolicySGRetriesPerRateCck = 1,1,1,1,1,1,1,5,1,1,1,1,1
RatePolicySGRetriesPerRatePbcc = 1,1,1,1,1,1,1,5,1,1,1,1,1
RatePolicySGRetriesPerRateOfdm = 1,1,1,1,1,1,1,5,1,1,1,1,1
RatePolicySGRetriesPerRateOfdmA = 1,1,1,1,1,1,1,5,1,1,1,1,1
#
# Power Manager
#
BeaconListenInterval = 1 # the number of N-Beacon or N-DTim
DtimListenInterval = 1 # Dm: Different value causes DHCP problem
dot11PowerMode = 0 # 0 - Auto
# 1 - Active
# 2 - Short Doze
# 3 - Long Doze
PowerMgmtHangOverPeriod = 5 # in mSec units
AutoPowerModeDozeMode = 2 # 2 - Short Doze
# 3 - Long Doze
AutoPowerModeActiveTh = 15 # packets per second
AutoPowerModeDozeTh = 8 # packets per seconds - threshold for entering ELP in Auto mode
defaultPowerLevel = 0 # 0 - ELP
# 1 - PD
# 2 - AWAKE
PowerSavePowerLevel = 0 # 0 - ELP
# 1 - PD
# 2 - AWAKE
OsDbgState = 0x01e9003c # -1 or 0xffffffff -all (opens debug messages in o.s. only - sevirity+modules)
#############################################################
# Configure the severity table (0 = Disable/ 1 = Enable)
#
# Byte #0: Init
# Byte #1: Information
# Byte #2: Warning
# Byte #3: Error
# Byte #4: Fatal Error
# Byte #5: SM
# Byte #6: Console
# Byte #7: Debug RX
# Byte #8: Debug TX
# Byte #9: Debug Control
# Byte #10: Debug GWSI Recording
#############################################################
ReportSeverityTable = "00011010000"
BeaconReceiveTime = 50
#
# Default Driver Scan Parameters for BG band
#
FirstConnScanBandB_ChannelList = 1,2,3,4,5,6,7,8,9,10,11,12,13,14 # channel list to scan seperated with comma
FirstConnScanBandB_MinDwellTime = 30000 # Min dwell time in micro seconds
FirstConnScanBandB_MaxDwellTime = 60000 # Max dwell time in micro seconds
FirstConnScanBandB_NumOfProbReqs = 3 # Number of prob request
FirstConnScanBandB_ProbReqRate = 2 # Prob request rate
FirstConnScanBandB_TxPowerLevel = 255 # Tx power for every prob request - Dbm/10 units
# Default Driver Scan Parameters for A band
FirstConnScanBandA_ChannelList = 36,40,44,48,52,56,60,64,100,104,108,112,149,153,157,161 # channel list to scan seperated with comma
FirstConnScanBandA_MinDwellTime = 30000 # Min dwell time in micro seconds
FirstConnScanBandA_MaxDwellTime = 60000 # Max dwell time in micro seconds
FirstConnScanBandA_NumOfProbReqs = 3 # Number of prob request
FirstConnScanBandA_ProbReqRate = 32 # Prob request rate
FirstConnScanBandA_TxPowerLevel = 255 # Tx power for every prob request - Dbm/10 units
#
# QOS UPSD
#
desiredPsMode = 0 # Global Power save delivery protocol (1 - UPSD, 0 - Legacy)
QOS_wmePsModeBE = 0 # Power save delivery protocol for BE AC (1 - UPSD, 0 - Legacy)
QOS_wmePsModeBK = 0 # Power save delivery protocol for BK AC (1 - UPSD, 0 - Legacy)
QOS_wmePsModeVI = 0 # Power save delivery protocol for VI AC (1 - UPSD, 0 - Legacy)
QOS_wmePsModeVO = 0 # Power save delivery protocol for VO AC (1 - UPSD, 0 - Legacy)
# QOS_PacketBurstEnable = 1 # Packet Burst for non-QOS protocol
#
# QOS Classifier
#
Clsfr_Type = 1 # 1 - DSCP, 2 - Port, 3 - IP+port
NumOfDstIPPortClassifiers = 3 # number of classifier entries
IPPortClassifier00_IPAddress = 0a 03 89 02 # IP address 10.3.137.2
IPPortClassifier00_Port = 5001 # Port 5001
IPPortClassifier00_DTag = 1 # User priority 1
IPPortClassifier01_IPAddress = 0a 03 89 02 # IP address 10.3.137.2
IPPortClassifier01_Port = 5002 # Port 5002
IPPortClassifier01_DTag = 4 # User priority 4
IPPortClassifier02_IPAddress = 0a 03 89 02 # IP address 10.3.137.2
IPPortClassifier02_Port = 5003 # Port 5003
IPPortClassifier02_DTag = 6 # User priority 6
NumOfCodePoints = 4
DSCPClassifier00_CodePoint = 0 #Best Effort
DSCPClassifier00_DTag = 0
DSCPClassifier01_CodePoint = 8 #Background
DSCPClassifier01_DTag = 1
DSCPClassifier02_CodePoint = 40 #Video
DSCPClassifier02_DTag = 5
DSCPClassifier03_CodePoint = 56 #Voice
DSCPClassifier03_DTag = 7
dot11MaxReceiveLifetime=512000
FracOfLifeTimeToDrop = 50
WiFiAdhoc = 0
WiFiWmmPS = 0 # Use 1 on WiFi test in order to configure PS to work in WMM mode
EarlyWakeUp = 1 # 0 - Disable , 1 - Enable
TxEnergyDetection = 0 # Use 1 for enabling
TriggeredScanTimeOut = 50000 # Maximum time in Us between 2 channels on triggered scan
# PsPoll delivery failure solution
PsPollDeliveryFailureRecoveryPeriod = 1000 # Time in Ms to stay ACTIVE ('0' to disable feature) (orig = 20)
ConsecutivePsPollDeliveryFailureThreshold = 15 # Number of failed PsPoll's to start ACTIVE time out (orig = 4)
# BT Coexistence configuration
BThWlanCoexistEnable = 2 # 0 - SG_ENABLE
# 1 - SG_DISABLE (default)
# 2 - SG_SENSE (auto-detect activity)
BThWlanCoexistParamsallowPaSdToggleDuringBtActivityEnable = 0 # 0
# 1 - (default)
BThWlanCoexistParamsnumberOWlanPackets = 2
BThWlanCoexistParamsnumberOfBtPackets = 6
# The timeout before falling asleep after PsPoll (default 15)
QOS_rxTimeoutPsPoll = 30
|
